ASTM D7794-14
(Practice)Standard Practice for Blending Mid-Level Ethanol Fuel Blends for Flexible-Fuel Vehicles with Automotive Spark-Ignition Engines
Standard Practice for Blending Mid-Level Ethanol Fuel Blends for Flexible-Fuel Vehicles with Automotive Spark-Ignition Engines
SCOPE
1.1 This practice applies to the blending of automotive spark-ignition engine fuels with ethanol concentrations greater than those suitable for conventional-fuel vehicles and less than the minimum ethanol content specification limits of Specification D5798. These mid-level ethanol fuel blends are for use in flexible-fuel vehicles and are sometimes referred to at retail as “Ethanol Flex Fuel.”
1.2 These mid-level ethanol fuel blends are only suitable for use in ground flexible-fuel vehicles equipped with spark-ignition engines. Flexible-fuel vehicles are designed to operate on gasoline or gasoline-ethanol blends that meet the requirements of Specification D4814, ethanol fuel blends that meet the requirements of Specification D5798, or any combination of these. In the United States, these vehicles are certified by the U.S. EPA as emissions compliant with these types of fuels.
1.3 The mid-level ethanol fuel blend shall be blended from either:
1.3.1 Denatured fuel ethanol conforming to the requirements of Specification D4806 with a reduced limit on inorganic chloride content that will ensure no more than 1 mg/kg inorganic chloride in the finished fuel and from spark-ignition engine fuel conforming to Specification D4814 (often at a distribution terminal or bulk plant), or
1.3.2 Ethanol fuel blends conforming to Specification D5798 and from spark-ignition engine fuel conforming to Specification D4814 (often at a retail site).
1.4 This practice describes the required procedures for blending various mid-level ethanol fuel blends for flexible-fuel vehicles at the bulk distribution point or retail/commercial delivery site. These requirements may be applied at other points in the production and distribution system when provided by agreement between the purchaser and the supplier.
1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D7794 − 14
Standard Practice for
Blending Mid-Level Ethanol Fuel Blends for Flexible-Fuel
1
Vehicles with Automotive Spark-Ignition Engines
This standard is issued under the fixed designation D7794; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 1.5 The values stated in SI units are to be regarded as
standard. No other units of measurement are included in this
1.1 This practice applies to the blending of automotive
standard.
spark-ignition engine fuels with ethanol concentrations greater
1.6 This standard does not purport to address all of the
than those suitable for conventional-fuel vehicles and less than
safety concerns, if any, associated with its use. It is the
the minimum ethanol content specification limits of Specifica-
responsibility of the user of this standard to establish appro-
tion D5798. These mid-level ethanol fuel blends are for use in
priate safety and health practices and determine the applica-
flexible-fuel vehicles and are sometimes referred to at retail as
bility of regulatory limitations prior to use.
“Ethanol Flex Fuel.”
1.2 Thesemid-levelethanolfuelblendsareonlysuitablefor 2. Referenced Documents
use in ground flexible-fuel vehicles equipped with spark-
2
2.1 ASTM Standards:
ignition engines. Flexible-fuel vehicles are designed to operate
D4057 Practice for Manual Sampling of Petroleum and
on gasoline or gasoline-ethanol blends that meet the require-
Petroleum Products
mentsofSpecificationD4814,ethanolfuelblendsthatmeetthe
D4175 Terminology Relating to Petroleum, Petroleum
requirements of Specification D5798, or any combination of
Products, and Lubricants
these. In the United States, these vehicles are certified by the
D4177 Practice for Automatic Sampling of Petroleum and
U.S. EPA as emissions compliant with these types of fuels.
Petroleum Products
D4806 Specification for Denatured Fuel Ethanol for Blend-
1.3 The mid-level ethanol fuel blend shall be blended from
ing with Gasolines for Use as Automotive Spark-Ignition
either:
Engine Fuel
1.3.1 Denatured fuel ethanol conforming to the require-
D4814 Specification for Automotive Spark-Ignition Engine
mentsofSpecificationD4806withareducedlimitoninorganic
Fuel
chloride content that will ensure no more than 1 mg/kg
D4815 Test Method for Determination of MTBE, ETBE,
inorganic chloride in the finished fuel and from spark-ignition
TAME, DIPE, tertiary-Amyl Alcohol and C to C Alco-
1 4
engine fuel conforming to Specification D4814 (often at a
hols in Gasoline by Gas Chromatography
distribution terminal or bulk plant), or
D5191 Test Method for Vapor Pressure of Petroleum Prod-
1.3.2 Ethanol fuel blends conforming to Specification
ucts (Mini Method)
D5798 and from spark-ignition engine fuel conforming to
D5501 Test Method for Determination of Ethanol and
Specification D4814 (often at a retail site).
Methanol Content in Fuels Containing Greater than 20%
Ethanol by Gas Chromatography
1.4 This practice describes the required procedures for
D5599 Test Method for Determination of Oxygenates in
blending various mid-level ethanol fuel blends for flexible-fuel
Gasoline by Gas Chromatography and Oxygen Selective
vehicles at the bulk distribution point or retail/commercial
Flame Ionization Detection
delivery site. These requirements may be applied at other
D5798 Specification for Ethanol Fuel Blends for Flexible-
pointsintheproductionanddistributionsystemwhenprovided
Fuel Automotive Spark-Ignition Engines
by agreement between the purchaser and the supplier.
D5842 Practice for Sampling and Handling of Fuels for
Volatility Measurement
1
This practice is under the jurisdiction of ASTM Committee D02 on Petroleum
Products, Liquid Fuels, and Lubricants and is the direct responsibility of Subcom-
2
mittee D02.A0.02 on Oxygenated Fuels and Components. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Dec. 1, 2014. Published January 2015. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 2012. Last previous edition approved in 2012 as D7794 – 12. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/D7794-14. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D7794 − 14
D5854 Practice for Mixing and Handling of Liquid Samples ing with U.S. EPA requirements and ethanol fuel blends that
of Petroleum and Petrole
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D7794 − 12 D7794 − 14
Standard Practice for
Blending Mid-Level Ethanol Fuel Blends for Flexible-Fuel
1
Vehicles with Automotive Spark-Ignition Engines
This standard is issued under the fixed designation D7794; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope Scope*
1.1 This practice applies to the blending of automotive spark-ignition engine fuels with ethanol concentrations greater than
those suitable for conventional-fuel vehicles and less than the minimum ethanol content specification limits of Specification
D5798. These mid-level ethanol fuel blends are for use in flexible-fuel vehicles and are sometimes referred to at retail as “Ethanol
Flex Fuel.”
1.2 These mid-level ethanol fuel blends are only suitable for use in ground flexible-fuel vehicles equipped with spark-ignition
engines. Flexible-fuel vehicles are designed to operate on gasoline or gasoline-ethanol blends that meet the requirements of
Specification D4814, ethanol fuel blends that meet the requirements of Specification D5798, or any combination of these. In the
United States, these vehicles are certified by the U.S. EPA as emissions compliant with these types of fuels.
1.3 The mid-level ethanol fuel blend shall be blended from either:
1.3.1 Denatured fuel ethanol conforming to the requirements of Specification D4806 with a reduced limit on inorganic chloride
content that will ensure no more than 1 mg/kg inorganic chloride in the finished fuel and from spark-ignition engine fuel
conforming to Specification D4814 (often at a distribution terminal or bulk plant), or
1.3.2 Ethanol fuel blends conforming to Specification D5798 and from spark-ignition engine fuel conforming to Specification
D4814 (often at a retail site).
1.4 This practice describes the required procedures for blending various mid-level ethanol fuel blends for flexible-fuel vehicles
at the bulk distribution point or retail/commercial delivery site. These requirements may be applied at other points in the production
and distribution system when provided by agreement between the purchaser and the supplier.
1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D4057 Practice for Manual Sampling of Petroleum and Petroleum Products
D4175 Terminology Relating to Petroleum, Petroleum Products, and Lubricants
D4177 Practice for Automatic Sampling of Petroleum and Petroleum Products
D4806 Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
D4814 Specification for Automotive Spark-Ignition Engine Fuel
D4815 Test Method for Determination of MTBE, ETBE, TAME, DIPE, tertiary-Amyl Alcohol and C to C Alcohols in
1 4
Gasoline by Gas Chromatography
D5191 Test Method for Vapor Pressure of Petroleum Products (Mini Method)
D5501 Test Method for Determination of Ethanol and Methanol Content in Fuels Containing Greater than 20% Ethanol by Gas
Chromatography
1
This practice is under the jurisdiction of ASTM Committee D02 on Petroleum Products, Liquid Fuels, and Lubricants and is the direct responsibility of Subcommittee
D02.A0.02 on Oxygenated Fuels and Components.
Current edition approved April 15, 2012Dec. 1, 2014. Published May 2012January 2015. Originally approved in 2012. Last previous edition approved in 2012 as
D7794 – 12. DOI: 10.1520/D7794–12.10.1520/D7794-14.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D7794 − 14
D5599 Test Method for Determination of Oxygenates in Gasoline by Gas Chromatography and Oxygen S
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.