ASTM C1077-12
(Practice)Standard Practice for Agencies Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Testing Agency Evaluation
Standard Practice for Agencies Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Testing Agency Evaluation
SIGNIFICANCE AND USE
4.1 The testing and inspection of concrete and concrete aggregates are important elements in obtaining quality construction. A testing agency providing these services must be selected with care.
4.2 A testing agency shall be deemed qualified to perform and report the results of its tests if the agency meets the requirements of this practice. The testing agency services shall be provided under the technical direction of a registered professional engineer.
4.3 This practice establishes essential characteristics pertaining to the organization, personnel, facilities, and quality systems of the testing agency. This practice may be supplemented by more specific criteria and requirements for particular projects.
SCOPE
1.1 This practice identifies and defines the duties, responsibilities, and minimum technical requirements of testing agency personnel and the minimum technical requirements for equipment utilized in testing concrete and concrete aggregates for use in construction.
1.2 This practice provides criteria for the evaluation of the capability of a testing agency to perform designated ASTM test methods on concrete and concrete aggregates. It can be used by an evaluation authority in the inspection or accreditation of a testing agency or by other parties to determine if the agency is qualified to conduct the specified tests.Note 1—Specification E329 provides criteria for the evaluation of agencies that perform the inspection of concrete during placement.
1.3 This practice provides criteria for Inspection Bodies and Accreditation Bodies that provide services for evaluation of testing agencies in accordance with this practice.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.vate, engaged in the testing of masonry materials.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: C1077 − 12
StandardPractice for
Agencies Testing Concrete and Concrete Aggregates for
Use in Construction and Criteria for Testing Agency
1
Evaluation
This standard is issued under the fixed designation C1077; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope* C39/C39M Test Method for Compressive Strength of Cylin-
drical Concrete Specimens
1.1 This practice identifies and defines the duties,
C40 Test Method for Organic Impurities in FineAggregates
responsibilities, and minimum technical requirements of test-
for Concrete
ing agency personnel and the minimum technical requirements
C117 Test Method for Materials Finer than 75-µm (No. 200)
for equipment utilized in testing concrete and concrete aggre-
Sieve in Mineral Aggregates by Washing
gates for use in construction.
C125 Terminology Relating to Concrete and Concrete Ag-
1.2 This practice provides criteria for the evaluation of the
gregates
capabilityofatestingagencytoperformdesignatedASTMtest
C127 Test Method for Density, Relative Density (Specific
methodsonconcreteandconcreteaggregates.Itcanbeusedby
Gravity), and Absorption of Coarse Aggregate
an evaluation authority in the inspection or accreditation of a
C128 Test Method for Density, Relative Density (Specific
testing agency or by other parties to determine if the agency is
Gravity), and Absorption of Fine Aggregate
qualified to conduct the specified tests.
C136 Test Method for Sieve Analysis of Fine and Coarse
Aggregates
NOTE 1—Specification E329 provides criteria for the evaluation of
agencies that perform the inspection of concrete during placement.
C138/C138M Test Method for Density (Unit Weight),Yield,
and Air Content (Gravimetric) of Concrete
1.3 This practice provides criteria for Inspection Bodies and
C143/C143M Test Method for Slump of Hydraulic-Cement
Accreditation Bodies that provide services for evaluation of
Concrete
testing agencies in accordance with this practice.
C172 Practice for Sampling Freshly Mixed Concrete
1.4 This standard does not purport to address all of the
C173/C173M Test Method forAir Content of Freshly Mixed
safety concerns, if any, associated with its use. It is the
Concrete by the Volumetric Method
responsibility of the user of this standard to establish appro-
C231 Test Method for Air Content of Freshly Mixed Con-
priate safety and health practices and determine the applica-
crete by the Pressure Method
bility of regulatory limitations prior to use.
C617 Practice for Capping Cylindrical Concrete Specimens
C802 Practice for Conducting an Interlaboratory Test Pro-
2. Referenced Documents
gram to Determine the Precision of Test Methods for
2
2.1 ASTM Standards:
Construction Materials
C31/C31M Practice for Making and Curing Concrete Test
C1064/C1064M Test Method for Temperature of Freshly
Specimens in the Field
Mixed Hydraulic-Cement Concrete
C1231/C1231M Practice for Use of Unbonded Caps in
1
This practice is under the jurisdiction of ASTM Committee C09 on Concrete DeterminationofCompressiveStrengthofHardenedCon-
and ConcreteAggregatesand is the direct responsibility of Subcommittee C09.98 on
crete Cylinders
Evaluation of Laboratories.
D75 Practice for Sampling Aggregates
Current edition approved Sept. 15, 2012. Published November 2012. Originally
D2419 Test Method for Sand Equivalent Value of Soils and
approved in 1987. Last previous edition approved in 2011 as C1077–11c. DOI:
10.1520/C1077-12.
Fine Aggregate
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
E4 Practices for Force Verification of Testing Machines
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
E11 Specification for Woven Wire Test Sieve Cloth and Test
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. Sieves
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1077 − 12
E329 Specification for Agencies Engaged in Construction vided in the Qualification of Personnel and Laboratory Evalu-
Inspection, Testing, or Special Inspection ation section of the Manual of Aggregate and Concrete
6
E1301 Guide for Proficiency Testing by Interlaboratory Testing. Thelistismerelyacollectionoforganizationswilling
3
Comparisons (Withdrawn 2012) to provide this service and is not an endorsement of any
particular organization. Other organizations m
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C1077 − 11c C1077 − 12
Standard Practice for
Agencies Testing Concrete and Concrete Aggregates for
Use in Construction and Criteria for Testing Agency
1
Evaluation
This standard is issued under the fixed designation C1077; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
1.1 This practice identifies and defines the duties, responsibilities, and minimum technical requirements of testing agency
personnel and the minimum technical requirements for equipment utilized in testing concrete and concrete aggregates for use in
construction.
1.2 This practice provides criteria for the evaluation of the capability of a testing agency to perform designated ASTM test
methods on concrete and concrete aggregates. It can be used by an evaluation authority in the inspection or accreditation of a
testing agency or by other parties to determine if the agency is qualified to conduct the specified tests.
NOTE 1—Specification E329 provides criteria for the evaluation of agencies that perform the inspection of concrete during placement.
1.3 This practice provides criteria for Inspection Bodies and Accreditation Bodies that provide services for evaluation of testing
agencies in accordance with this practice.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
C31/C31M Practice for Making and Curing Concrete Test Specimens in the Field
C39/C39M Test Method for Compressive Strength of Cylindrical Concrete Specimens
C40 Test Method for Organic Impurities in Fine Aggregates for Concrete
C117 Test Method for Materials Finer than 75-μm (No. 200) Sieve in Mineral Aggregates by Washing
C125 Terminology Relating to Concrete and Concrete Aggregates
C127 Test Method for Density, Relative Density (Specific Gravity), and Absorption of Coarse Aggregate
C128 Test Method for Density, Relative Density (Specific Gravity), and Absorption of Fine Aggregate
C136 Test Method for Sieve Analysis of Fine and Coarse Aggregates
C138/C138M Test Method for Density (Unit Weight), Yield, and Air Content (Gravimetric) of Concrete
C143/C143M Test Method for Slump of Hydraulic-Cement Concrete
C172 Practice for Sampling Freshly Mixed Concrete
C173/C173M Test Method for Air Content of Freshly Mixed Concrete by the Volumetric Method
C231 Test Method for Air Content of Freshly Mixed Concrete by the Pressure Method
C617 Practice for Capping Cylindrical Concrete Specimens
C802 Practice for Conducting an Interlaboratory Test Program to Determine the Precision of Test Methods for Construction
Materials
C1064/C1064M Test Method for Temperature of Freshly Mixed Hydraulic-Cement Concrete
1
This practice is under the jurisdiction of ASTM Committee C09 on Concrete and Concrete Aggregatesand is the direct responsibility of Subcommittee C09.98 on
Evaluation of Laboratories.
Current edition approved Dec. 1, 2011Sept. 15, 2012. Published January 2012November 2012. Originally approved in 1987. Last previous edition approved in 2011 as
C1077–11b.–11c. DOI: 10.1520/C1077-11c.10.1520/C1077-12.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1077 − 12
C1231/C1231M Practice for Use of Unbonded Caps in Determination of Compressive Strength of Hardened Concrete Cylinders
D75 Practice for Sampling Aggregates
D2419 Test Method for Sand Equivalent Value of Soils and Fine Aggregate
E4 Practices for Force Verification of Testing Machines
E11 Specification for Woven Wire Test Sieve Cloth and Test Sieves
E329 Specification for Agencies Engaged in Construction Inspection, Testing, or Special Inspection
3
E1301 Guide
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.