ASTM A424/A424M-09a(2016)
(Specification)Standard Specification for Steel, Sheet, for Porcelain Enameling
Standard Specification for Steel, Sheet, for Porcelain Enameling
ABSTRACT
This specification covers standard requirements for sheet steel in coils and cut lengths for porcelain enameling. Heat analysis of Type I, Type II, and Type III steels shall conform to the prescribed chemical composition for carbon, manganese, phosphorus, sulfur, and others. However, an exception is made on carbon, since heat analysis of carbon is not appropriate for Type I. The material shall also conform to the required mechanical properties such as bending and formability.
SCOPE
1.1 This specification covers sheet steel in coils and cut lengths for porcelain enameling. The compositions and processing of these steels are such that articles for porcelain enameling may be fabricated from them and, under proper conditions, enameled. The steels are furnished as Type I, Type II, and Type III. Type I and Type II are supplied in two designations, Commercial Steel and Drawing Steel. Type III steel is interstitial-free and does not require a designation.
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.3 Tolerances are found in General Requirements Specifications A568/A568M and A635/A635M. The appropriate General Requirements specification is applied based on the thickness and width of the product ordered.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: A424/A424M −09a (Reapproved 2016)
Standard Specification for
1
Steel, Sheet, for Porcelain Enameling
This standard is issued under the fixed designationA424/A424M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope* 3. Terminology
1.1 This specification covers sheet steel in coils and cut
3.1 Definitions—For definitions of other terms used in this
lengths for porcelain enameling. The compositions and pro-
specification, refer to Terminology A941.
cessing of these steels are such that articles for porcelain
3.2 Definitions of Terms Specific to This Standard:
enameling may be fabricated from them and, under proper
3.2.1 base coat—also known as ground coat. This coating
conditions, enameled. The steels are furnished as Type I, Type
layer is applied directly to the steel and promotes adhesion of
II, and Type III. Type I and Type II are supplied in two
the coating system to the steel.
designations, Commercial Steel and Drawing Steel. Type III
3.2.2 cover coat—This coating layer is usually applied over
steel is interstitial-free and does not require a designation.
the base or ground coat to improve the appearance and provide
1.2 The values stated in either SI units or inch-pound units
the proper color.
are to be regarded separately as standard. The values stated in
3.2.3 direct cover coat—This refers to a single coating
each system may not be exact equivalents; therefore, each
application that provides both adequate adhesion and appear-
system shall be used independently of the other. Combining
ance.
values from the two systems may result in non-conformance
with the standard.
4. Classification
1.3 Tolerances are found in General Requirements Specifi-
cationsA568/A568MandA635/A635M.TheappropriateGen- 4.1 Types:
eral Requirements specification is applied based on the thick-
4.1.1 Type I steel has an extremely low carbon level
ness and width of the product ordered.
achieved through sheet decarburization. This material is suit-
able for direct cover coat enameling practice, but this require-
2. Referenced Documents
ment must be indicated by the purchaser in accordance with
2
5.1.6. This material is also suitable for ground and cover coat
2.1 ASTM Standards:
A568/A568M Specification for Steel, Sheet, Carbon, enameling practice. It has good sag resistance and good
formability.
Structural,andHigh-Strength,Low-Alloy,Hot-Rolledand
Cold-Rolled, General Requirements for
4.1.2 Type II steel is suitable for applications where ground
A635/A635M Specification for Steel, Sheet and Strip, and cover coat enameling operations are employed. The
Heavy-Thickness Coils, Hot-Rolled, Alloy, Carbon,
composition of the Type II steel is obtained in melting
Structural, High-Strength Low-Alloy, and High-Strength operations.
Low-Alloy with Improved Formability, General Require-
4.1.3 Type III is an interstitial-free steel and is suitable for
ments for
applications where ground and cover coat enameling opera-
A941 TerminologyRelatingtoSteel,StainlessSteel,Related
tions are employed. The composition of the Type III steel is
Alloys, and Ferroalloys
obtained in melting operations. It has good sag resistance and
excellent formability.
1 4.2 Product Designations:
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
Stainless Steel and Related Alloysand is the direct responsibility of Subcommittee
4.2.1 Commercial Steel is intended for parts where bending,
A01.19 on Steel Sheet and Strip.
moderate forming, or moderate drawing may be involved.
Current edition approved May 1, 2016. Published May 2016. Originally
4.2.2 Drawing Steel is intended for fabricating identified
approved in 1958. Last previous edition approved in 2009 as A424/A424M – 09a.
DOI: 10.1520/A0424_A0424M-09AR16.
parts where the draw is particularly severe or where the
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
material shall be essentially free of changes in mechanical
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
properties over a period of time. Drawing Steel should be
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. specified where the formed material shall be essentially free of
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
A424/A424M − 09a (2016)
cover coat, 0
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: A424/A424M − 09a A424/A424M − 09a (Reapproved 2016)
Standard Specification for
1
Steel, Sheet, for Porcelain Enameling
This standard is issued under the fixed designation A424/A424M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope*
1.1 This specification covers sheet steel in coils and cut lengths for porcelain enameling. The compositions and processing of
these steels are such that articles for porcelain enameling may be fabricated from them and, under proper conditions, enameled.
The steels are furnished as Type I, Type II, and Type III. Type I and Type II are supplied in two designations, Commercial Steel
and Drawing Steel. Type III steel is interstitial-free and does not require a designation.
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in non-conformance with the standard.
1.3 Tolerances are found in General Requirements Specifications A568/A568M and A635/A635M. The appropriate General
Requirements specification is applied based on the thickness and width of the product ordered.
2. Referenced Documents
2
2.1 ASTM Standards:
A568/A568M Specification for Steel, Sheet, Carbon, Structural, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled,
General Requirements for
A635/A635M Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Hot-Rolled, Alloy, Carbon, Structural,
High-Strength Low-Alloy, and High-Strength Low-Alloy with Improved Formability, General Requirements for
A941 Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys
3. Terminology
3.1 Definitions—For definitions of other terms used in this specification, refer to Terminology A941.
3.2 Definitions of Terms Specific to This Standard:
3.2.1 base coat—also known as ground coat. This coating layer is applied directly to the steel and promotes adhesion of the
coating system to the steel.
3.2.2 cover coat—This coating layer is usually applied over the base or ground coat to improve the appearance and provide the
proper color.
3.2.3 direct cover coat—This refers to a single coating application that provides both adequate adhesion and appearance.
4. Classification
4.1 Types:
4.1.1 Type I steel has an extremely low carbon level achieved through sheet decarburization. This material is suitable for direct
cover coat enameling practice, but this requirement must be indicated by the purchaser in accordance with 5.1.6. This material is
also suitable for ground and cover coat enameling practice. It has good sag resistance and good formability.
4.1.2 Type II steel is suitable for applications where ground and cover coat enameling operations are employed. The composition
of the Type II steel is obtained in melting operations.
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel, Stainless Steel and Related Alloysand is the direct responsibility of Subcommittee A01.19
on Steel Sheet and Strip.
Current edition approved Nov. 1, 2009May 1, 2016. Published December 2009May 2016. Originally approved in 1958. Last previous edition approved in 2009 as
A424 – 09.A424/A424M – 09a. DOI: 10.1520/A0424_A0424M-09a.10.1520/A0424_A0424M-09AR16.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
A424/A424M − 09a (2016)
4.1.3 Type III is an interstitial-free steel and is suitable for applications where ground and cover coat enameling operations are
employed. The composition of the Type III steel is obtained in melting operations. It has good sag resistance and excellent
formability.
4.2 Product Designations:
4.2.1 Commercial Steel is intended for parts where bending, moderate
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.