ASTM B209M-02e1

Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate [Metric]

SCOPE
1.1 This specification covers aluminum and aluminum alloy flat sheet, coiled sheet, and plate, in the alloys (Note 1) and tempers shown in Table 2 and 3, and in the following finishes:
1.1.1 Plate in all alloys and sheet in heat-treatable alloys: mill finish.
1.1.2 Sheet in nonheat-treatable alloys: mill finish, one-side bright mill finish, standard one-side bright finish, and standard two-sides bright finish.
1.2 Alloy and temper designations are in accordance with ANSI H35.1M. The equivalent Unified Numbering System alloy designations are those of Table 1 preceded by A9, for example, A91100 for aluminum 1100 in accordance with Practice E 527.
Note 1—Throughout this specification, use of the term alloyin the general sense includes aluminum as well as aluminum alloy.
Note 2—See Specification B 632/B 632M for Tread Plate.
1.3 This specification is the metric counterpart of Specification B 209.
1.4 For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A2.

General Information

• Status: Historical
• Publication Date: 09-Apr-2002
• ICS: 77.120.10 - Aluminium and aluminium alloys
• Technical Committee: B07 - Light Metals and Alloys
• Drafting Committee: B07.03 - Aluminum Alloy Wrought Products

Relations

• Replaces: ASTM B209M-02 - Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate [Metric]
• Effective Date: 10-Apr-2002
• Referred By: ASTM D2510-22 - Standard Test Method for Adhesion of Solid Film Lubricants
• Effective Date: 10-Apr-2002
• Referred By: ASTM B928/B928M-15 - Standard Specification for High Magnesium Aluminum-Alloy Products for Marine Service and Similar Environments
• Effective Date: 10-Apr-2002
• Referred By: ASTM D4956-19 - Standard Specification for Retroreflective Sheeting for Traffic Control
• Effective Date: 10-Apr-2002
• Referred By: ASTM F626-14(2023) - Standard Specification for Fence Fittings
• Effective Date: 10-Apr-2002
• Referred By: ASTM B881-17 - Standard Terminology Relating to Aluminum- and Magnesium-Alloy Products
• Effective Date: 10-Apr-2002
• Referred By: ASTM B746/B746M-22 - Standard Specification for Corrugated Aluminum Alloy Structural Plate for Field-Bolted Pipe, Pipe-Arches, and Arches
• Effective Date: 10-Apr-2002
• Referred By: ASTM B744/B744M-15(2020) - Standard Specification for Aluminum Alloy Sheet for Corrugated Aluminum Pipe
• Effective Date: 10-Apr-2002
• Referred By: ASTM B947-14(2020)e1 - Standard Practice for Hot Rolling Mill Solution Heat Treatment for Aluminum Alloy Plate
• Effective Date: 10-Apr-2002
• Referred By: ASTM B745/B745M-15(2021) - Standard Specification for Corrugated Aluminum Pipe for Sewers and Drains
• Effective Date: 10-Apr-2002
• Referred By: ASTM F1099M-18(2023) - Standard Specification for Rat Guards, Ship’s (Metric)
• Effective Date: 10-Apr-2002

Standards Content (Sample)

NOTICE: This standard has either been superceded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
e1
Designation: B 209M – 02
METRIC
Standard Specification for
1
Aluminum and Aluminum-Alloy Sheet and Plate [Metric]
This standard is issued under the fixed designation B 209M; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1
e NOTE—The Summary of Changes was updated editorially September 2002.
2
1. Scope * Cast Aluminum- and Magnesium-Alloy Products [Metric]
B 594 Practice for Ultrasonic Inspection of Aluminum-
1.1 This specification covers aluminum and aluminum alloy
2
Alloy Wrought Products for Aerospace Applications
flat sheet, coiled sheet, and plate, in the alloys (Note 1) and
B 632/B 632M Specification for Aluminum-Alloy Rolled
tempers shown inTables 2 and 3, and in the following finishes:
2
Tread Plate
1.1.1 Plate in all alloys and sheet in heat-treatable alloys:
B 660 Practices for Packaging/Packing of Aluminum and
mill finish.
2
Magnesium Products
1.1.2 Sheet in nonheat-treatable alloys: mill finish, one-side
B 666/B 666M Practice for Identification Marking of Alu-
bright mill finish, standard one-side bright finish, and standard
2
minum and Magnesium Products
two-sides bright finish.
B 918 Practice for Heat Treatment of Wrought Aluminum
1.2 Alloy and temper designations are in accordance with
2
Alloys
ANSI H35.1M. The equivalent Unified Numbering System
3
E 3 Methods of Preparation of Metallographic Specimens
alloy designations are those of Table 1 preceded by A9, for
E 29 Practice for Using Significant Digits in Test Data to
example, A91100 for aluminum 1100 in accordance with
4
Determine Conformance with Specifications
Practice E 527.
E 34 Test Methods for Chemical Analysis of Aluminum and
NOTE 1—Throughout this specification, use of the term alloy in the 5
Aluminum-Base Alloys
general sense includes aluminum as well as aluminum alloy.
E 55 Practice for Sampling Wrought Nonferrous Metals and
NOTE 2—See Specification B 632/B 632M for Tread Plate.
5
Alloys for Determination of Chemical Composition
3
1.3 This specification is the metric counterpart of Specifi-
E 290 Test Method for Bend Test for Ductility
3
cation B 209.
E 407 Practice for Microetching Metals and Alloys
6
1.4 For acceptance criteria for inclusion of new aluminum
E 527 Practice for Numbering Metals and Alloys (UNS)
and aluminum alloys in this specification, see Annex A2.
E 607 Test Method for Optical Emission Spectrometric
Analysis of Aluminum and Aluminum Alloys by the
2. Referenced Documents
5
Point-to-Plane Technique, Nitrogen Atmosphere
2.1 The following documents of the issue in effect on the
E 716 Practices for Sampling Aluminum and Aluminum
date of material purchase, unless otherwise noted, form a part 5
Alloys for Spectrochemical Analysis
of this specification to the extent referenced herein:
E 1004 Practice for Determining Electrical Conductivity
2.2 ASTM Standards: 7
Using the Electromagnetic Eddy-Current Method
B 209 Specification for Aluminum and Aluminum-Alloy
E 1251 Test Method for Optical Emission Spectrometric
2
Sheet and Plate
Analysis of Aluminum and Aluminum Alloys by the Argon
B 548 Method for Ultrasonic Inspection of Aluminum-
Atmosphere, Point-to-Plane, Unipolar Self-Initiating Ca-
2
Alloy Plate for Pressure Vessels 5
pacitor Discharge
B 557M Test Methods for Tension Testing Wrought and
G 34 Test Method for Exfoliation Corrosion Susceptibility
1
This specification is under the jurisdiction of ASTM Committee B07 on Light
3
Metals and Alloys and is the direct responsibility of Subcommittee B07.03 on Annual Book of ASTM Standards, Vol 03.01.
4
Aluminum Alloy Wrought Products. Annual Book of ASTM Standards, Vol 14.02.
5
Current edition approved Apr. 10, 2002. Published June 2002. Originally Annual Book of ASTM Standards, Vol 03.05.
6
published as B 209M – 78. Last previous edition B 209M – 01. Annual Book of ASTM Standards, Vol 01.01.
2 7
Annual Book of ASTM Standards, Vol 02.02. Annual Book of ASTM Standards, Vol 03.03.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
NOTICE: This standard has either been superceded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
e1
B209M–02
A,B,C
TABLE 1 Chemical Composition Limits
D
Other Elements
Manga- Magne- Chro- Tita- Alumi-
Alloy Silicon Iron Copper Zinc
nese sium mium nium E num
Each Total
F G
1060 0.25 0.35 0.05 0.03 0.03 . 0.05 0.0
...