iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D6037-96(2002)

(Test Method)

Standard Test Methods for Dry Abrasion Mar Resistance of High Gloss Coatings

Standard Test Methods for Dry Abrasion Mar Resistance of High Gloss Coatings

SIGNIFICANCE AND USE
Coatings, particularly the high gloss coatings used on automobiles, boats, toys, etc., are subject to a wide variety of conditions (for example, wiping, cleaning, and exposure) that can mar their surface. The ability of these coatings to maintain their appearance is an important product attribute. These test methods provide a way to estimate the ability of high gloss coatings to resist mar damage.
These test methods do not provide fundamental values. However they are suitable for estimating the ability of high gloss coatings to resist mar.
Since the susceptibility of coatings to marring varies widely, the number of cycles that are needed to cause “relevant” mar damage also varies. Usually, 2 to 50 cycles are sufficient.
SCOPE
1.1 Two test methods are included. Test Method A uses a device that contains an abrasive wheel. Test Method B uses a device that contains a wheel that has been fitted with abrasive paper. Either method can be used to evaluate the dry abrasion mar resistance of coatings applied to planar, rigid surfaces. Each test method provides good discrimination between highly mar resistant coatings.  
1.2 Mar resistance is assessed by measuring the gloss of abraded and unabraded areas. Mar resistance is directly related to the coating's ability to retain gloss in abraded areas.  
Note 1—The mar resistance values obtained by these test methods have no absolute significance. They should only be used to derive relative performance rankings for test panels that have been prepared from the series of coatings that are currently being evaluated. If mar resistance values are quoted between laboratories, it is essential that a common standard be measured and that the values be compared to that standard. Even then, the values should be used with caution.  
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.  
1.4  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
09-Nov-1996
ICS
25.220.01 - Surface treatment and coating in general
Technical Committee
D01 - Paint and Related Coatings, Materials, and Applications
Drafting Committee
D01.23 - Physical Properties of Applied Paint Films
Current Stage
Ref Project

Relations

Replaces
ASTM D6037-96 - Standard Test Methods for Dry Abrasion Mar Resistance of High Gloss Coatings
Effective Date
10-Nov-1996
Replaced By
ASTM D6037-96(2008) - Standard Test Methods for Dry Abrasion Mar Resistance of High Gloss Coatings
Effective Date
01-Jul-2008
Referred By
ASTM G195-22 - Standard Guide for Conducting Wear Tests Using a Rotary Platform Abraser
Effective Date
10-Nov-1996
Referred By
ASTM D5146-10(2019) - Standard Guide to Testing Solvent-Borne Architectural Coatings
Effective Date
10-Nov-1996
Referred By
ASTM D5324-16(2022) - Standard Guide for Testing Water-Borne Architectural Coatings
Effective Date
10-Nov-1996
Referred By
ASTM D6279-20 - Standard Test Method for Rub Abrasion Mar Resistance of High Gloss Coatings
Effective Date
10-Nov-1996
Referred By
ASTM D7187-20 - Standard Test Method for Measuring Mechanistic Aspects of Scratch/Mar Behavior of Paint Coatings by Nanoscratching
Effective Date
10-Nov-1996

Buy Standard

ASTM D6037-96(2002) - Standard Test Methods for Dry Abrasion Mar Resistance of High Gloss CoatingsASTM D6037-96(2002) - Standard Test Methods for Dry Abrasion Mar Resistance of High Gloss Coatings
PreviousNext
Standard
ASTM D6037-96(2002) - Standard Test Methods for Dry Abrasion Mar Resistance of High Gloss Coatings
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D 6037 – 96 (Reapproved 2002)
Standard Test Methods for
1
Dry Abrasion Mar Resistance of High Gloss Coatings
This standard is issued under the fixed designation D 6037; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope D 1186 Test Methods for Nondestructive Measurement of
Dry Film Thickness of Nonmagnetic Coatings Applied to
1.1 Two test methods are included. Test Method A uses a
2
a Ferrous Base
device that contains an abrasive wheel. Test Method B uses a
D 1400 Test Method for Nondestructive Measurement of
device that contains a wheel that has been fitted with abrasive
DryFilmThicknessofNonconductiveCoatingsAppliedto
paper. Either method can be used to evaluate the dry abrasion
2
a Nonferrous Metal Base
mar resistance of coatings applied to planar, rigid surfaces.
D 2240 Test Method for Rubber Property—Durometer
Each test method provides good discrimination between highly
3
Hardness
mar resistant coatings.
D 3924 Specification for Standard Environment for Condi-
1.2 Mar resistance is assessed by measuring the gloss of
tioning and Testing Paint, Varnish, Lacquer and Related
abraded and unabraded areas. Mar resistance is directly related
2
Materials
to the coating’s ability to retain gloss in abraded areas.
D 4449 Test Method for Visual Evaluation of Gloss Differ-
NOTE 1—The mar resistance values obtained by these test methods 2
ences Between Surfaces of Similar Appearance
have no absolute significance. They should only be used to derive relative
performance rankings for test panels that have been prepared from the
3. Terminology
series of coatings that are currently being evaluated. If mar resistance
3.1 Definitions of Terms Specific to This Standard:
values are quoted between laboratories, it is essential that a common
3.1.1 mar resistance—the ability of a coating to resist
standard be measured and that the values be compared to that standard.
Even then, the values should be used with caution.
permanent deformation or fracture, resulting from the applica-
tion of a dynamic mechanical force. These test methods
1.3 The values stated in inch-pound units are to be regarded
measure resistance to visible damage caused by mild abrasion.
as the standard. The values given in parentheses are for
information only.
4. Summary of Test Methods
1.4 This standard does not purport to address all of the
4.1 The coatings that are being evaluated are applied at
safety concerns, if any, associated with its use. It is the
uniform dry film thickness to planar panels of uniform surface
responsibility of the user of this standard to establish appro-
texture. After drying or curing, or both, the panels are marred.
priate safety and health practices and determine the applica-
Mar resistance is assessed by measuring the coating’s gloss
bility of regulatory limitations prior to use.
within the abraded and unabraded areas of test panels. Mar
2. Referenced Documents resistance is directly related to the coating’s ability to retain
gloss in abraded areas.
2.1 ASTM Standards:
2
D 523 Test Method for Specular Gloss
5. Significance and Use
D 609 Practice for Preparation of Cold-Rolled Steel Panels
5.1 Coatings, particularly the high gloss coatings used on
for Testing Paint, Varnish, Conversion Coatings, and
2
automobiles, boats, toys, etc., are subject to a wide variety of
Related Coating Products
conditions (for example, wiping, cleaning, and exposure) that
D 823 Practices for Producing Films of Uniform Thickness
2
can mar their surface. The ability of these coatings to maintain
of Paint, Varnish, and Related Products on Test Panels
their appearance is an important product attribute. These test
D 1005 Test Method for Measurement of Dry-Film Thick-
2
methods provide a way to estimate the ability of high gloss
ness of Organic Coatings Using Micrometers
coatings to resist mar damage.
5.2 These test methods do not provide fundamental values.
1
However they are suitable for estimating the ability of high
This test method is under the jurisdiction of ASTM Committee D01 on Paint
and Related Coatings, Materials, andApplications and is the direct responsibility of
gloss coatings to resist mar.
Subcommittee D01.23 on Physical Properties of Applied Paint Films.
Current edition approved Nov. 10, 1996. Published January 1997.
2 3
Annual Book of ASTM Standards, Vol 06.01. Annual Book of ASTM Standards, Vol 09.01.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D 6037
5
1
5.3 Since the susceptibility of c
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D6093-97(2022)(Test Method)
Standard Test Method for Percent Volume Nonvolatile Matter in Clear or Pigmented Coatings Using a Helium Gas Pycnometer

SIGNIFICANCE AND USE
4.1 This test method measures the volume of dry coating obtainable from a given volume of liquid coating. This value is useful for calculating the volatile organic content (VOC) of a coating and could be used to estimate the coverage (square feet of surface covered at a specified dry film thickness per unit volume) obtainable with different coating products.
Note 1: In Practice D3960 paragraph 10.3.1, the equation for calculating the VOC content using the percent volume nonvolatile is given. Prior to this method a satisfactory procedure for measuring percent volume nonvolatile did not exist (see Note 11 in Practice D3960).
Note 2: Since the actual coverage of a coating includes the void volume and the porosity of the film, the coverage value calculated from this method will be inaccurate by that amount, that is, the actual coverage will be greater. The higher the pigment to binder ratio (P/B) of a coating or the higher content of void containing material (latices, hollow beads, etc.) or both, the greater will be the deviation of the coverage calculation (This is also true to a lesser degree with Test Method D2697).  
4.2 For various reasons the volume nonvolatile value obtained for a coating is often not equal to that predicted from simple linear addition of the weights and volumes of the raw materials in a formulation. One reason is that the volume occupied by a solution of resin in solvent may be the same, greater, or less than the total volume of the separate ingredients. Such contraction or expansion of resin solutions is governed by a number of factors, one of which is the extent and direction of spread between solubility parameters of the resin and solvent.  
4.3 The spatial configuration of the pigment particles and the degree to which the pigment particles are filled with the binder also affect the volume of a dry coating film. Above the critical pigment volume concentration, the apparent volume of the dry film is significantly greater than theoretical...
SCOPE
1.1 This test method covers the determination of the percent volume nonvolatile matter of a variety of clear and pigmented coatings. The approach used should provide faster and more accurate results than the use of the liquid displacement technique in Test Method D2697, particularly for coatings that are difficult to wet or that contain voids, cracks or other defects. The improvement in accuracy stems from the superior ability of helium gas under pressure to penetrate very small pores and surface irregularities in dried films. This provides a more accurate determination of void volumes than can be obtained via liquid displacement.  
1.2 The technique will provide results under the following constraints:  
1.2.1 The stability of the helium gas pycnometer is greater than ±0.005 cm3.  
1.2.2 Test specimen weights are greater than 1 g.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D6677-18(2022)(Test Method)
Standard Test Method for Evaluating Adhesion by Knife

SIGNIFICANCE AND USE
4.1 Coatings, to perform satisfactorily, must adhere to the substrates on which they are applied. This test method has been found useful as a simple means of assessing the adhesion of coatings. Although this method is a qualitative (subjective) test it has been used in industry for many years and can provide valuable information.  
4.2 Other adhesion test methods may be useful in obtaining quantitative results. See Test Methods D2197, D3359, D4541, and D7234.  
4.3 The Performance Evaluation Scale (see Table 1) is based on both the degree of difficulty to remove the coating from the substrate and the size of removed coating chip.  
4.4 This test method does not have a known correlation to other adhesion test methods (pull-off, tape, etc.).  
4.5 A coating that has a high degree of cohesive strength may appear to have worse adhesion than one that is brittle and hence fractures easily when probed.  
4.6 This method is not to be used on overly thick coatings, that is, those which cannot be cut to the substrate with a utility knife in one stroke.
SCOPE
1.1 This test method covers the procedure for assessing the adhesion of coating films to substrate by using a knife.  
1.2 This test method is used to establish whether the adhesion of a coating to a substrate or to another coating (in multi-coat systems) is at a generally adequate level.
Note 1: The term “substrate” relates to the basic surface on which a coating adheres (may be steel, concrete, etc. or other coating).  
1.3 This method can be used in the laboratory and field.  
1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D7541-11(2022)(Practice)
Standard Practice for Estimating Critical Surface Tensions

SIGNIFICANCE AND USE
5.1 Knowledge of the critical surface tension of substrates, primers and other coatings is useful for explaining or predicting wettability by paints and other coatings applied to those surfaces. Surfaces with low critical surface tensions usually are prone to suffer defects such as crawling, picture framing, cratering and loss of adhesion when painted. Low or irregular values, or both, often are indicative of contamination that could reduce adhesion. Surfaces with high critical surface tensions are easy to wet and usually provide an excellent platform for painting.  
5.2 The swab, marking pen and draw-down tests all simulate the application of a film  
5.3 The swab and marking pen techniques are simple and rapid and are particularly useful for testing in the field or on curved, irregular or porous surfaces where contact angles cannot be measured. The drop test does not work well on such surfaces and the draw-down method requires a flat specimen that is relatively large.  
5.4 The estimation of critical surface tension has been useful in characterizing surfaces before and after cleaning processes such as power washes and solvent wipes in order to evaluate the efficiency of the cleaning.  
5.5 One or more of these techniques could be the basis of a go/no-go quality control test where if a certain liquid wets, the surface is acceptable for painting, but if that liquid retracts and crawls, the surface is not acceptable.  
5.6 Another go/no go test is possible where the test liquid is a paint and the surface is a substrate, primer or basecoat. A form of this test has been used for coatings for plastics.
SCOPE
1.1 This practice covers procedures for estimating values of the critical surface tension of surfaces by observing the wetting and dewetting of a series of liquids (usually organic solvents) applied to the surface in question.  
1.2 Another technique, measurement of the contact angles, θ, of a series of test liquids and plotting cos θ versus surface tension (Zisman plots), provides data that allow the determination of more exact values for critical surface tension.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D6676/D6676M-21(Test Method)
Standard Test Method for Cathodic Disbonding of Exterior Pipeline Coatings at Elevated Temperatures Using Interior Heating

SIGNIFICANCE AND USE
4.1 Damage to a pipe coating is almost unavoidable during transportation and construction. Breaks or holidays in pipe coatings may expose the pipe to possible corrosion since, after a pipe has been installed underground, the surrounding earth will be moisture-bearing and will constitute an effective electrolyte. Applied cathodic protection potentials may cause loosening of the coating, beginning at holiday edges. Spontaneous holidays may also be caused by such potentials. Usually exterior pipeline coatings applied over pipes carrying hot media (oil, gas) are exposed to high temperature inside the pipe and low temperature outside and subjected to temperature gradient. Heat flux is directed from metal (substrate) to the coating. This test method provides accelerated conditions for cathodic disbondment to occur under simulated heating and provides a measure of resistance of coatings to this type of action.  
4.2 The effects of the test are to be evaluated by physical examinations and monitoring the current drawn by the test specimens. Usually there is no correlation between the two methods of evaluation, but both methods are significant. Physical examination consists of assessing the effective contact of the coating with the metal surface in terms of observed differences in the relative adhesive bond. It is usually found that the cathodically disbonded area propagates from an area where adhesion is zero to an area where adhesion reaches the original level. An intermediate zone of decreased adhesion may also be present.  
4.3 Assumptions associated with test results include:  
4.3.1 Maximum adhesion, or bond, is found in the coating that was not immersed in the test liquid, and  
4.3.2 Decreased adhesion in the immersed test area is the result of cathodic disbondment.  
4.4 Ability to resist disbondment is a desired quality on a comparative basis, but disbondment in this test method is not necessarily an adverse indication of coating performance. The virtue of this...
SCOPE
1.1 This test method describes an accelerated procedure for determining comparative characteristics of coating systems applied to the exterior of steel pipe for the purpose of preventing or mitigating corrosion that may occur in underground or immersion where the pipe is carrying heated media and is under cathodic protection. This test method is intended for use with samples of coated pipe, or with a specimen cut from the section of coated pipe or flat plates and is applicable to such samples when the coating is characterized by function as an electrical barrier.  
1.2 This test method is intended to simulate conditions when external coatings are exposed to high temperature inside the pipe and to an ambient temperature outside, and thus are subjected to temperature gradient. If elevated temperatures are required but without temperature gradient, see Test Method G42.  
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    9 pages
    English language
    sale 15% off
  • Standard
    9 pages
    English language
    sale 15% off
ASTM
ASTM D6037-21(Test Method)
Standard Test Methods for Dry Abrasion Mar Resistance of High Gloss Coatings

SIGNIFICANCE AND USE
5.1 Coatings, particularly the high gloss coatings used on automobiles, boats, toys, etc., are subject to a wide variety of conditions (for example, wiping, cleaning, and exposure) that can mar their surface. The ability of these coatings to maintain their appearance is an important product attribute. These test methods provide a way to estimate the ability of high gloss coatings to resist mar damage.  
5.2 These test methods do not provide fundamental values. However they are suitable for estimating the ability of high gloss coatings to resist mar.  
5.3 Since the susceptibility of coatings to marring varies widely, the number of cycles that are needed to cause “relevant” mar damage also varies. Usually, 2 to 50 cycles are sufficient.
SCOPE
1.1 This test method covers procedures for evaluating the relative mar resistance of high gloss coatings. Two test methods are included. Test Method A uses a device that rotates the test specimen on a vertical axis, against the sliding rotation of two abrading wheels. Test Method B uses a device that reciprocates a specimen in a horizontal plane over a stationary wheel that has been fitted with abrasive paper and is advanced after each double stroke. Either method can be used to evaluate the dry abrasion mar resistance of coatings applied to planar, rigid surfaces. Each test method provides good discrimination between highly mar resistant coatings.
Note 1: The mar resistance values obtained by these test methods have no absolute significance. They should only be used to derive relative performance rankings for test panels that have been prepared from the series of coatings that are currently being evaluated. If mar resistance values are quoted between laboratories, it is essential that a common standard be measured and that the values be compared to that standard. Even then, the values should be used with caution.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM D8380-21(Test Method)
Standard Test Method for Dry Abrasion Resistance of Hydrophobic and Omniphobic Coatings

SIGNIFICANCE AND USE
5.1 The test method is to be used to determine the abrasion resistance or mechanical durability of thin omniphobic or thin hydrophobic coatings. These coatings are often used to enhance the surface’s value by promoting fingerprint resistance, water removal, stain resistance, and easy-clean properties. A comparison of the contact angle and the depreciation of that contact angle due to exposure to mechanical abrasion determines the coating’s ability to remain effective after exposure to environmental abrasion.  
5.1.1 The test method is used to appraise the removal of thin films when gravimetric measurements will not yield a detectable change in film mass due to the small amount of material comprising these films, which are on the order of nanometers thick.  
5.1.2 Only fully cured specimens are evaluated unless otherwise specified and agreed upon by the interested parties.  
5.2 Different coating materials may be evaluated for relative durability by evaluating abrasion cycles versus water contact angle using this method.  
5.3 Different curing or conditioning methods may be evaluated by preparing test specimens with the same coating and then evaluating abrasion resistance using this method.
SCOPE
1.1 This test method describes a procedure for evaluating dry abrasion resistance of a thin hydrophobic or omniphobic coating, or both. The coating is typically less than 100 nm thick and is applied to a planar, glass substrate by application methods including, but not limited to, physical vapor deposition (PVD), dip, or spray.  
1.2 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard with the exception of angular measurement which are reported in degrees.
Note 1: This test method measures a static contact angle and is not equivalent to Test Method C813 which measures an advancing contact angle.
Note 2: Test Method D4060 is not applicable to hydrophobic and omniphobic coatings because the molecular monolayer does not generally result in a detectable weight change to the specimen after subjecting it to abrasion.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D5618-20(Test Method)
Standard Test Method for Measurement of Barnacle Adhesion Strength in Shear

SIGNIFICANCE AND USE
4.1 This test method is designed as a screening test in the evaluation of coating systems and other materials designed to resist biofouling attachment.  
4.2 The degree and type of barnacle fouling will vary according to the geographic location of test sites and the time of year when tests are implemented. Surfaces with known barnacle adhesive shear strength should be exposed to provide comparative data.
SCOPE
1.1 This test method covers the measurement of barnacle adhesion in shear to surfaces exposed in the marine environment. It is used to establish the ability of a surface to reduce biofouling adhesion. Surfaces with known barnacle adhesion strengths are included to serve as controls.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D6990-20(Practice)
Standard Practice for Evaluating Biofouling Resistance and Physical Performance of Marine Coating Systems

SIGNIFICANCE AND USE
5.1 This practice is designed to provide guidance to a panel inspector for quantitative and consistent evaluation of coating performance from test panels coated with marine antifouling coating systems. The practice assesses performance of coating systems based on both antifouling and physical properties.  
5.2 The user is cautioned that the results are representative for the specific region and time of year in which the specimens are immersed. It shall be noted that interpretation of results will depend on the geographical location where the test is conducted, whether the coated specimens are exposed either totally or partially immersed, under static or dynamic conditions, and position and orientation.  
5.3 Simultaneous testing of a proven standard antifouling coating system (known to minimize fouling accumulation, for example, containing biocide or active agent(s) to prevent fouling settlement/growth) in the specific marine environment shall be included as a reference to assist in interpretation of results. In addition, a negative control (inert surface susceptible to heavy fouling) shall be included on a regular basis. For the exposure to be valid, the surface of the negative control should show heavy fouling relative to the standard system(s).  
5.4 Marine coating systems that produce positive results relevant to the standard system(s) show potential for use in protecting underwater marine structures.  
5.5 The format can be utilized independent of exposure protocol and coating type, and provides the end user with a consistent practice and format for reporting of performance rating.
SCOPE
1.1 This practice establishes a practice for evaluating degree of biofouling settlement on and physical performance of marine coating systems when panels coated with such coating systems are subjected to immersion conditions in a marine environment. Guidance for preparation or exposure and handling of test specimens can be found in related ASTM standards as noted below (see Section 2).  
1.2 This practice and related exposure methodologies are designed as tools for the relative assessment of coating performance, and in no way are to be used as an absolute indicator of long-term performance under all conditions and in all environments. There can be high variability among and within exposure sites with respect to water quality and population or species of fouling organisms, and coating performance may vary with these and other properties.  
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. A specific hazard statement is given in Section 6.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    13 pages
    English language
    sale 15% off
ASTM
ASTM D8331/D8331M-20(Test Method)
Standard Test Method for Measurement of Film Thickness of Thin-Film Coatings by Non-Destructive Means Using Ruggedized Optical Interference

SIGNIFICANCE AND USE
4.1 Coating film thickness plays a critical role in the performance of the final product. This includes physical properties (abrasion/scratch resistance, color, gloss), chemical properties (solvent resistance), corrosion resistance, and long-term durability (color change, chalk, fade).  
4.2 The non-destructive measurement system based on ruggedized optical interference transforms signal outputs in coating film thickness using digital formulas (or “recipes”) which are reproducible from one instrument to another.  
4.3 The ROI measurement unit takes a significant number of measurements which can be read in a determined period of time and each of these data points is recorded and reportable.  
4.4 Due to the number of variables that can affect film thickness during application and the number of variables that must be set in the measurement unit while determining a recipe, it is important for the producer and the user to agree upon recipe settings depending on the coating system.
SCOPE
1.1 This test method encompasses measuring the film thickness of a coil coated organic coating layer. Operators can use this method in process during the coating application or in a laboratory setting.  
1.2 This test method does not specify the expected film thickness/test results for a coating, nor the specific “recipe” file needed to measure a coating.  
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D6686-01(2019)(Test Method)
Standard Test Method for Evaluation of Tannin Stain Resistance of Coatings

SIGNIFICANCE AND USE
5.1 Tannins and other chromophoric extractives are naturally occurring materials in wood and wood-based substrates. Tannins are prevalent to a high degree in cedar, redwood, oak, and to a lesser degree in white and yellow pine. Tannins are also present in varying amounts in wood composition products. These extractives are solubilized and darkened in color by aqueous coatings, resulting in unsightly yellow or brown discolorations. This test method is designed to show the relative ability of paints to prevent tannin bleed-through. Typically, cedar or redwood panels are used for this test.
SCOPE
1.1 This test method is an accelerated procedure to determine the effectiveness of latex coatings at preventing the migration of tannin stains from wood substrates.  
1.2 The values in SI units are to be regarded as the standard. The values in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off