iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM F626-08(2013)

(Specification)

Standard Specification for Fence Fittings

Standard Specification for Fence Fittings

ABSTRACT
This specification covers the materials, coating requirements, and inspection of the following fence accessories that are used for chain-link fences: post and line caps; rail and brace ends; top rail sleeves; tie wires, clips, and fasteners; tension and brace bands; tension bars; truss rod assembly; barbed wire arms; color coating of fittings; and fitting size terminology.
SCOPE
1.1 This specification covers the materials, coating requirements, and inspection of fence accessories for chain-link fence for the following:  
1.1.1 Post and line caps,  
1.1.2 Rail and brace ends,  
1.1.3 Top rail sleeves,  
1.1.4 Tie wires, clips, and fasteners,  
1.1.5 Tension and brace bands,  
1.1.6 Tension bars,  
1.1.7 Truss rod assembly,  
1.1.8 Barbed wire arms,  
1.1.9 Color coating of fittings, and  
1.1.10 Fitting size terminology.  
1.2 The values stated in inch-pound units are to be regarded as the standard. The SI values given in parentheses are for information only.

General Information

Status
Historical
Publication Date
28-Feb-2013
ICS
23.040.40 - Metal fittings
91.090 - External structures
Technical Committee
F14 - Fences
Drafting Committee
F14.40 - Chain Link Fence and Wire Accessories
Current Stage
Ref Project

Relations

Replaces
ASTM F626-08 - Standard Specification for Fence Fittings
Effective Date
01-Mar-2013
Replaced By
ASTM F626-14 - Standard Specification for Fence Fittings
Effective Date
01-Apr-2014
Referred By
ASTM F969-11(2016) - Standard Practice for Construction of Chain-Link Tennis Court Fence
Effective Date
01-Mar-2013
Referred By
ASTM E2942-22 - Standard Guide for Security of Tank Farm Installations for Compliance with Spill Prevention, Control and Countermeasure Plan (SPCC) Regulations
Effective Date
01-Mar-2013
Referred By
ASTM F3558-22 - Standard Guide for Chain-Link Pickleball Court Fences
Effective Date
01-Mar-2013
Referred By
ASTM F1553-11(2022) - Standard Guide for Specifying Chain Link Fence
Effective Date
01-Mar-2013
Referred By
ASTM F567-23 - Standard Practice for Installation of Chain-Link Fence
Effective Date
01-Mar-2013
Referred By
ASTM F3000/F3000M-13(2022) - Standard Specification for Polymer Privacy Insert Slats for Chain Link Fabric and Privacy Chain Link Fabric Manufactured Containing Pre-Installed Privacy Slats
Effective Date
01-Mar-2013
Referred By
ASTM F2780-20 - Standard Guide for Design and Construction of Expanded Metal Security Fences and Barriers
Effective Date
01-Mar-2013
Referred By
ASTM F2611-15 - Standard Guide for Design and Construction of Chain Link Security Fencing
Effective Date
01-Mar-2013
Referred By
ASTM F654-07(2017) - Standard Specification for Residential Chain Link Fence Gates
Effective Date
01-Mar-2013

Buy Standard

ASTM F626-08(2013) - Standard Specification for Fence FittingsASTM F626-08(2013) - Standard Specification for Fence Fittings
PreviousNext
Technical specification
ASTM F626-08(2013) - Standard Specification for Fence Fittings
English language
5 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F626 −08(Reapproved 2013)
Standard Specification for
1
Fence Fittings
ThisstandardisissuedunderthefixeddesignationF626;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope B209M Specification for Aluminum and Aluminum-Alloy
Sheet and Plate (Metric)
1.1 This specification covers the materials, coating
B211 Specification for Aluminum and Aluminum-Alloy
requirements, and inspection of fence accessories for chain-
Rolled or Cold Finished Bar, Rod, and Wire
link fence for the following:
B211M Specification for Aluminum and Aluminum-Alloy
1.1.1 Post and line caps,
Rolled or Cold-Finished Bar, Rod, and Wire (Metric)
1.1.2 Rail and brace ends,
B221 Specification forAluminum andAluminum-Alloy Ex-
1.1.3 Top rail sleeves,
truded Bars, Rods, Wire, Profiles, and Tubes
1.1.4 Tie wires, clips, and fasteners,
B221M Specification for Aluminum and Aluminum-Alloy
1.1.5 Tension and brace bands,
Extruded Bars, Rods, Wire, Profiles, and Tubes (Metric)
1.1.6 Tension bars,
B429/B429M Specification for Aluminum-Alloy Extruded
1.1.7 Truss rod assembly,
Structural Pipe and Tube
1.1.8 Barbed wire arms,
B800 Specification for 8000 Series Aluminum Alloy Wire
1.1.9 Color coating of fittings, and
for Electrical Purposes—Annealed and Intermediate Tem-
1.1.10 Fitting size terminology.
pers
1.2 The values stated in inch-pound units are to be regarded
F552 Terminology Relating to Chain Link Fencing
as the standard. The SI values given in parentheses are for
F668 Specification for Polyvinyl Chloride (PVC), Polyolefin
information only.
and Other Polymer-Coated Steel Chain Link Fence Fabric
F934 Specification for Colors for Polymer-Coated Chain
2. Referenced Documents
Link Fence Materials
2
2.1 ASTM Standards:
2.2 U.S. Government Standard:
A641/A641M Specification for Zinc–Coated (Galvanized)
MIL-R-60346-C Roving, Glass, Fibrous (For Prepreg Tape
Carbon Steel Wire
and Roving, Filament Winding, and Pultrusion Applica-
A809 Specification for Aluminum-Coated (Aluminized) 3
tions)
Carbon Steel Wire
A817 Specification for Metallic-Coated Steel Wire for
3. Post and Line Caps
Chain-Link Fence Fabric and Marcelled Tension Wire
3.1 Post and line caps shall be fabricated from pressed steel
B26/B26M Specification for Aluminum-Alloy Sand Cast-
or cast iron and hot-dip galvanized with a minimum of 1.2
2
ings
2
oz/ft (366 g/m ) of zinc coating of surface area, or from
B85 Specification for Aluminum-Alloy Die Castings
aluminum alloy 360.0 conforming to die cast Specification
B108 Specification for Aluminum-Alloy Permanent Mold
B85, or sand cast or permanent mold alloy 356.0 or 713.0
Castings
conforming to Specification B26/B26M or B108.
B117 Practice for Operating Salt Spray (Fog) Apparatus
3.2 Post and line caps shall be designed to fit snugly over
B209 Specification for Aluminum and Aluminum-Alloy
posts and exclude moisture from inside when tubular posts are
Sheet and Plate
used.
1
This specification is under the jurisdiction ofASTM Committee F14 on Fences
4. Rail and Brace Ends
and is the direct responsibility of Subcommittee F14.40 on Chain Link Fence and
Wire Accessories. 4.1 Rail and brace ends, when required, shall be fabricated
Current edition approved March 1, 2013. Published March 2013. Originally
from pressed steel or cast iron, and hot-dip galvanized with a
approved in 1979. Last previous edition approved in 2008 as F626 - 08. DOI:
2 2
minimum of 1.2 oz/ft (366 g/m ) of zinc coating of surface
10.1520/F0626-08R13.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on AvailablefromStandardizationDocumentsOrderDesk,Bldg.4SectionD,700
the ASTM website. Robbins Ave., Philadelphia, PA 19111–5094, Attn: NPODS.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F626−08 (2013)
NOTE 1—Heavier zinc coatings than those listed in 6.1.1.1 (1) and
area, or from aluminum alloy 360.0 (see Specification B85), or
6.1.1.2(1)maybespecifiedifdesired,tomatchtheminimumzinccoating
alloy 356.0 or 713.0 (see Specification B26/B26M or Specifi-
specified for the fence fabric.
cation B108).
6.1.1.3 Nine-gage (0.148 6 0.005-in. (3.76 6 0.125-mm))
4.2 Rail and brace ends, or other approved means of
or (6-gage 0.192 6 0.005-in. (4.88 6 0.125-mm)) aluminum
connection, shall be provided when top rail or brace are
Alloy 1350-H19 or approved equal.
required.
6.1.2 High-Security Round Wire Ties shall be one o
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM F626-14(2023)(Specification)
Standard Specification for Fence Fittings

ABSTRACT
This specification covers the materials, coating requirements, and inspection of the following fence accessories that are used for chain-link fences: post and line caps; rail and brace ends; top rail sleeves; tie wires, clips, and fasteners; tension and brace bands; tension bars; truss rod assembly; barbed wire arms; color coating of fittings; and fitting size terminology.
SCOPE
1.1 This specification covers the materials, coating requirements, and inspection of fence accessories for chain-link fence for the following:  
1.1.1 Post and line caps,  
1.1.2 Rail and brace ends,  
1.1.3 Top rail sleeves,  
1.1.4 Tie wires, clips, and fasteners,  
1.1.5 Tension and brace bands,  
1.1.6 Tension bars,  
1.1.7 Truss rod assembly,  
1.1.8 Barbed wire arms,  
1.1.9 Color coating of fittings, and  
1.1.10 Fitting size terminology.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off
ASTM
ASTM F626-14(2023)(Specification)
Standard Specification for Fence Fittings

ABSTRACT
This specification covers the materials, coating requirements, and inspection of the following fence accessories that are used for chain-link fences: post and line caps; rail and brace ends; top rail sleeves; tie wires, clips, and fasteners; tension and brace bands; tension bars; truss rod assembly; barbed wire arms; color coating of fittings; and fitting size terminology.
SCOPE
1.1 This specification covers the materials, coating requirements, and inspection of fence accessories for chain-link fence for the following:  
1.1.1 Post and line caps,  
1.1.2 Rail and brace ends,  
1.1.3 Top rail sleeves,  
1.1.4 Tie wires, clips, and fasteners,  
1.1.5 Tension and brace bands,  
1.1.6 Tension bars,  
1.1.7 Truss rod assembly,  
1.1.8 Barbed wire arms,  
1.1.9 Color coating of fittings, and  
1.1.10 Fitting size terminology.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off
ASTM
ASTM F1210-23(Guide)
Standard Guide for Ecological Considerations for the Use of Oil Spill Dispersants in Freshwater and Other Inland Environments, Lakes and Large Water Bodies

SIGNIFICANCE AND USE
3.1 This guide is meant to aid response teams who may use it during spill response planning and spill events.  
3.2 This guide should be adapted to site specific circumstance.
SCOPE
1.1 This guide covers the use of oil spill dispersants to assist in the control of oil spills. The guide is written with the goal of minimizing the environmental impacts of oil spills; this goal is the basis on which the recommendations are made. Aesthetic and socioeconomic factors are not considered, although these and other factors are often important in spill response.  
1.2 Spill responders have available several means to control or clean up spilled oil. Chemical dispersants should be given equal consideration with other spill countermeasures.  
1.3 This is a general guide only. Oil, as used in this guide, includes crude oils and refined petroleum products. Differences between individual dispersants or between different oil products are not considered. The dispersibility of the oil with the chosen dispersant should be evaluated.  
1.4 The guide is organized by habitat type, for example, small ponds and lakes, rivers and streams, and land. It considers the use of dispersants primarily to protect habitats from impact (or to minimize impacts).  
1.5 This guide applies only to freshwater and other inland environments. It does not consider the direct application of dispersants to subsurface waters.  
1.6 In making dispersant use decisions, appropriate government authorities should be consulted as required by law.  
1.7 This guide does not address getting regulatory approval.  
1.8 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    3 pages
    English language
    sale 15% off
  • Guide
    3 pages
    English language
    sale 15% off
ASTM
ASTM C596-23(Test Method)
Standard Test Method for Drying Shrinkage of Mortar Containing Hydraulic Cement

SIGNIFICANCE AND USE
4.1 This test method establishes a selected set of conditions of temperature, relative humidity and rate of evaporation of the environment to which a mortar specimen of stated composition shall be subjected for a specified period of time during which its change in length is determined and designated “drying shrinkage.”  
4.2 The drying shrinkage of mortar as determined by this test method has a linear relation to the drying shrinkage of concrete made with the same cement and exposed to the same drying conditions.4 Hence this test method may be used when it is desired to develop data on the effect of a hydraulic cement on the drying shrinkage of concrete made with that cement.
SCOPE
1.1 This test method determines the change in length on drying of mortar bars containing hydraulic cement and graded standard sand.  
1.2 The values stated in SI units are to be regarded as standard. When combined standards are referenced, the selection of measurement system is at the user’s discretion subject to the requirements of the referenced standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Warning—Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and tissue upon prolonged exposure).2  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D1751-23(Specification)
Standard Specification for Preformed Expansion Joint Filler for Concrete Paving and Structural Construction (Nonextruding and Resilient Asphalt Types)

SCOPE
1.1 This specification covers preformed expansion joint filler having relatively little extrusion and substantial recovery after release from compression.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
Note 1: Attention is called to Specifications D1752 and D994/D994M.  
1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM B637-23(Specification)
Standard Specification for Precipitation-Hardening and Cold Worked Nickel Alloy Bars, Forgings, and Forging Stock for Moderate or High Temperature Service

ABSTRACT
This specification covers hot- and cold-worked precipitation-hardenable nickel alloy rod, bar, forgings, and forging stock for high-temperature service. Chemical analysis shall be performed on the alloy and shall conform to the chemical composition requirement in carbon, manganese, silicon, phosphorus, sulfur, chromium, cobalt, molybdenum, columbium, tantalum, titanium, aluminum, zirconium, boron, iron, copper, and nickel. The material shall follow recommended annealing treatment, solution treatment, stabilizing treatment, and precipitation hardening treatment. Tension testing, hardness testing and stress-rupture testing shall be performed on the material and shall comply to the required tensile strength, yield strength, elongation, reduction in area, and Brinell hardness.
SCOPE
1.1 This specification2 covers hot- and cold-worked precipitation-hardenable nickel alloy rod, bar, forgings, and forging stock for moderate or high temperature service (Table 1).  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off
  • Technical specification
    7 pages
    English language
    sale 15% off
ASTM
ASTM D8139-23(Specification)
Standard Specification for Semi-Rigid, Closed-Cell Polypropylene Foam, Preformed Expansion Joint Fillers for Concrete Paving and Structural Construction

SCOPE
1.1 This specification covers preformed expansion joint fillers made from closed-cell polypropylene foam materials having suitable compressibility, recovery from compression, nonextruding, and weather-resistant characteristics.  
1.1.1 Type I, closed-cell polypropylene foam.  
1.2 These joint fillers are intended for use in concrete pavements in full-depth joints. There are several variations in size with typical thicknesses of 1/2 in. (12.7 mm), 3/4 in. (19.05 mm), and 1 in. (25.4 mm); typical widths of 31/2 in. (88.9 mm), 4 in. (101.6 mm), 5 in. (127 mm), 6 in. (152.5 mm), 7 in. (177.8 mm), 8 in. (203.2 mm), or 48 in. (1.2 m) sheet; and typical lengths of 5 ft (1.52 m) and 10 ft (3.05 m).  
1.3 The values stated in inch-pound units are to be regarded as the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM F3337-23(Guide)
Standard Guide for Taking Property and Behavior Measurements on Weathered Fractions of Oil

SIGNIFICANCE AND USE
5.1 A standard procedure is necessary to establish property changes for spilled oils or petroleum products at different oil weathering stages.  
5.2 This procedure employs standardized equipment, and test procedures.  
5.3 This procedure should be performed at the stages of weathering corresponding to the spill conditions of interest.
SCOPE
1.1 This guide summarizes methods to fractionate oil by evaporative weathering and then measure the properties and behavior of the weathered oil. The results of this guide can provide oil behavior data for input into oil spill models and response method selection.  
1.2 This guide covers general procedures for oil weathering and behavior and does not cover all possible procedures which may be applicable to this topic.  
1.3 The results obtained using this guide are intended to provide baseline data for the behavior of oil and petroleum products when spilled and input to oil spill models.  
1.4 The results obtained using this guide can be used directly to predict certain facets of oil spill behavior or as input to oil spill models.  
1.5 The accuracy of the guide depends very much on the representative nature of the oil sample used. Certain oils can have different properties depending on their chemical contents at the moment a sample is taken.  
1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    4 pages
    English language
    sale 15% off
  • Guide
    4 pages
    English language
    sale 15% off
ASTM
ASTM D6390-23(Test Method)
Standard Test Method for Determination of Draindown Characteristics in Uncompacted Asphalt Mixtures

SIGNIFICANCE AND USE
5.1 This test method can be used to determine whether the amount of draindown measured for a given asphalt mixture is within specified acceptable levels. The test provides an evaluation of the draindown potential of an asphalt mixture during mixture design and/or during field production. This test is primarily used for mixtures with high coarse aggregate content such as porous asphalt (open-graded friction course) and stone matrix asphalt (SMA).
Note 1: The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Specification D3666 are generally considered capable of competent and objective testing, sampling, inspection, etc. Users of this standard are cautioned that compliance with Specification D3666 alone does not completely ensure reliable results. Reliable results depend on many factors; following the suggestions of Specification D3666 or some similar acceptable guideline provides a means of evaluating and controlling some of those factors.
SCOPE
1.1 This test method covers the determination of the amount of draindown in an uncompacted asphalt mixture sample when the sample is held at elevated temperatures comparable to those encountered during the production, storage, transport, and placement of the mixture. The test is particularly applicable to mixtures such as porous asphalt (open-graded friction course) and stone matrix asphalt (SMA).  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM B472-23(Specification)
Standard Specification for Nickel Alloy Billets and Bars for Reforging

ABSTRACT
This specification covers UNS N06002, UNS N06030, UNS N06035, UNS N06022, UNS N06200, UNS N06230, UNS N06600, UNS N06617, UNS N06625, UNS N08020, UNS N08026, UNS N08024, UNS N08120, UNS N08926, UNS N08367, UNS N10242, UNS N10276, UNS N10665, UNS N10675, UNS N12160, UNS R20033, UNS N06059, UNS N06686, UNS N10629, UNS N08031, UNS N06045, UNS N06025, and UNS R30556 nickel alloy billets and bars for reforging. The products shall be hot worked from ingots by rolling, forging, extruding, hammering, or pressing. The material shall conform to the chemical composition requirements prescribed by the reference material. The chemical composition of the material shall be determined by chemical analysis in accordance with test method E1473.
SCOPE
1.1 This specification covers UNS N06002, UNS N06030, UNS N06035, UNS N06022, UNS N06200, UNS N10362, UNS N06230, UNS N06600, UNS N06617, UNS N06625, UNS N08020, UNS N08026, UNS N08024, UNS N08120, UNS N08926, UNS N08367, UNS N10242, UNS N10276, UNS N10665, UNS N10675, UNS N12160, UNS R20033, UNS N06059, UNS N06686, UNS N10629, UNS N08031, UNS N06045, UNS N06025, UNS N06699, and UNS R305562 billets and bars for reforging.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off
  • Technical specification
    5 pages
    English language
    sale 15% off