iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D5751-99(2019)

(Specification)

Standard Specification for Adhesives Used for Laminate Joints in Nonstructural Lumber Products

Standard Specification for Adhesives Used for Laminate Joints in Nonstructural Lumber Products

ABSTRACT
This specification covers performance levels for adhesives to be used in laminate joints in nonstructural lumber products. Such products include, but are not limited to, interior and exterior mouldings, window and door components or parts, and bonded lumber panels. This specification is to be used to evaluate adhesives as well as the adhesive bonds in nonstructural-glued-lumber products. Dry test, soak test, elevated temperature test, boil test, and vacuum pressure test shall be performed to meet the requirements prescribed. The precision and bias of exposure condition shall be tested to meet the requirements prescribed.
SCOPE
1.1 This specification covers performance levels for adhesives to be used in laminate joints in nonstructural lumber products. Such products include, but are not limited to, interior and exterior mouldings, window and door components or parts, and bonded lumber panels. This specification is to be used to evaluate adhesives as well as the adhesive bonds in nonstructural-glued-lumber products.
Note 1: This specification supersedes the laminate-joint portion of Specification D3110.
Note 2: See 3.2.1 and 3.2.2 for descriptions of a dry-use-nonstructural adhesive and a wet-use-nonstructural adhesive.  
1.2 This specification applies to laminate-joint specimens made under both laboratory and field conditions. See Section 4 for limitations in using this specification to evaluate industrially manufactured laminate joint products.  
1.3 The following safety caveat applies only to the apparatus and test methods portions, Sections 6, 7, 8, and 9 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 The values stated in inch-pound units are to be regarded as standard.  
1.5 In this specification, laminate joint refers to both face and edge joints.  
1.6 The following index is provided as a guide to the test methods in this specification:    
Section  
Apparatus  
6  
Conditioning  
7  
Material and Preparation of Assemblies and Specimens  
8  
Exposure Conditions and Treatments  
9  
Testing, Calculation, and Reporting  
10
Note 3: The conditioning needed for various stages in the preparation of the specimens and for the exposure tests are given in Sections 7, 8, and 9.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

Status
Published
Publication Date
31-Jan-2019
ICS
83.180 - Adhesives
Technical Committee
D14 - Adhesives
Drafting Committee
D14.30 - Wood Adhesives
Current Stage
Ref Project

Relations

Refers
ASTM D2555-15 - Standard Practice for Establishing Clear Wood Strength Values
Effective Date
01-Sep-2015
Refers
ASTM D4442-15 - Standard Test Methods for Direct Moisture Content Measurement of Wood and Wood-Based Materials
Effective Date
01-Jun-2015
Refers
ASTM D2555-16 - Standard Practice for Establishing Clear Wood Strength Values
Effective Date
01-Aug-2016
Refers
ASTM D2555-17 - Standard Practice for Establishing Clear Wood Strength Values
Effective Date
15-Apr-2017
Refers
ASTM D2555-17a - Standard Practice for Establishing Clear Wood Strength Values
Effective Date
01-Aug-2017
Refers
ASTM D4442-16 - Standard Test Methods for Direct Moisture Content Measurement of Wood and Wood-Based Materials
Effective Date
15-Nov-2016
Refers
ASTM D4442-20 - Standard Test Methods for Direct Moisture Content Measurement of Wood and Wood-Based Materials
Effective Date
01-Mar-2020
Refers
ASTM E4-14 - Standard Practices for Force Verification of Testing Machines
Effective Date
01-Jun-2014
Referred By
ASTM D5266-13(2020) - Standard Practice for Estimating the Percentage of Wood Failure in Adhesive Bonded Joints
Effective Date
01-Feb-2019

Buy Standard

ASTM D5751-99(2019) - Standard Specification for Adhesives Used for Laminate Joints in Nonstructural Lumber ProductsASTM D5751-99(2019) - Standard Specification for Adhesives Used for Laminate Joints in Nonstructural Lumber Products
PreviousNext
Technical specification
ASTM D5751-99(2019) - Standard Specification for Adhesives Used for Laminate Joints in Nonstructural Lumber Products
English language
11 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:D5751 −99 (Reapproved 2019)
Standard Specification for
Adhesives Used for Laminate Joints in Nonstructural
1
Lumber Products
This standard is issued under the fixed designation D5751; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
NOTE 3—The conditioning needed for various stages in the preparation
1. Scope
of the specimens and for the exposure tests are given in Sections 7, 8, and
1.1 This specification covers performance levels for adhe-
9.
sives to be used in laminate joints in nonstructural lumber
1.7 This international standard was developed in accor-
products. Such products include, but are not limited to, interior
dance with internationally recognized principles on standard-
andexteriormouldings,windowanddoorcomponentsorparts,
ization established in the Decision on Principles for the
and bonded lumber panels. This specification is to be used to
Development of International Standards, Guides and Recom-
evaluate adhesives as well as the adhesive bonds in
mendations issued by the World Trade Organization Technical
nonstructural-glued-lumber products.
Barriers to Trade (TBT) Committee.
NOTE 1—This specification supersedes the laminate-joint portion of
Specification D3110. 2. Referenced Documents
NOTE 2—See 3.2.1 and 3.2.2 for descriptions of a dry-use-nonstructural
2
2.1 ASTM Standards:
adhesive and a wet-use-nonstructural adhesive.
D905 Test Method for Strength Properties of Adhesive
1.2 This specification applies to laminate-joint specimens
Bonds in Shear by Compression Loading
made under both laboratory and field conditions. See Section 4
D907 Terminology of Adhesives
for limitations in using this specification to evaluate industri-
D2555 PracticeforEstablishingClearWoodStrengthValues
ally manufactured laminate joint products.
D3110 Specification for Adhesives Used in Laminate Joints
1.3 The following safety caveat applies only to the appara-
for Nonstructural Glued Lumber Products (Withdrawn
3
tus and test methods portions, Sections 6, 7, 8, and 9 of this
1996)
specification: This standard does not purport to address all of
D4442 Test Methods for Direct Moisture Content Measure-
the safety concerns, if any, associated with its use. It is the
ment of Wood and Wood-Based Materials
responsibility of the user of this standard to establish appro-
D5266 Practice for Estimating the Percentage of Wood
priate safety, health, and environmental practices and deter-
Failure in Adhesive Bonded Joints
mine the applicability of regulatory limitations prior to use.
E4 Practices for Force Verification of Testing Machines
1.4 The values stated in inch-pound units are to be regarded
E6 Terminology Relating to Methods of Mechanical Testing
as standard.
E41 Terminology Relating to Conditioning (Withdrawn
3
2019)
1.5 In this specification, laminate joint refers to both face
E177 Practice for Use of the Terms Precision and Bias in
and edge joints.
ASTM Test Methods
1.6 The following index is provided as a guide to the test
E691 Practice for Conducting an Interlaboratory Study to
methods in this specification:
Determine the Precision of a Test Method
Section
Apparatus 6
3. Terminology
Conditioning 7
Material and Preparation of Assemblies and 8
3.1 Definitions:Many terms in this specification are defined
Specimens
in Terminologies D907, E6, and E41.
Exposure Conditions and Treatments 9
Testing, Calculation, and Reporting 10 3.1.1 bond, n—the union of materials by adhesives.
1 2
This specification is under the jurisdiction of ASTM Committee D14 on For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Adhesives and is the direct responsibility of Subcommittee D14.30 on Wood contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Adhesives. Standards volume information, refer to the standard’s Document Summary page on
Current edition approved Feb. 1, 2019. Published February 2019. Originally the ASTM website.
3
approved in 1995. Last previous edition approved in 2012 as D5751 – 99 (2012). The last approved version of this historical standard is referenced on
DOI: 10.1520/D5751-99R19. www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D5751−99 (2019)
3.1.2 laminate joint, n—in wood bonding, a joint made by 4.1.1 The dry test and exposure conditions and treatments
bonding layers of adherends face-t
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D7966/D7966M-16(2023)(Test Method)
Standard Test Method for Resistance to Creep of Adhesives in Static Shear by Compression Loading (Wood-to-Wood)

SIGNIFICANCE AND USE
5.1 This test method evaluates the performance of the adhesive in laminated wood as measured by resistance to creep under static load.  
5.2 Test results from the evaluation of adhesive creep resistance, under designated environmental conditions of the test, provide a measure of the adhesive’s ability to withstand constant loading over a relatively long period of time.  
5.3 Creep measured with this test method is normally used in conjunction with specifications such as, but not limited to Specification D2559 and CSA O112.9 to confirm suitability of an adhesive to resist creep under designed loads when subjected to specific levels of stress, load duration and environmental conditions.
SCOPE
1.1 This test method covers the determination of creep properties of structural adhesives in wood-to-wood bonds when a standardized specimen is subjected to shearing stresses at various levels of static load, constant temperature, and relative humidity. Apparatus and procedures are provided for shear deformation (creep) of adhesive bonds under static load. This test method is used under the indicated conditions to evaluate resistance to creep properties of a structural wood adhesive.  
1.2 The test method is used to evaluate creep performance of adhesives suitable for the bonding of wood, including treated wood, into structural wood products for general construction, marine use, or for other uses where a high-strength general construction, creep-resistant, durable adhesive bond is required. Individual block shear specimens are prepared from adhesively bonded laminations, subjected to a constant load under various combinations of temperature and relative humidity, and the amount of creep measured.  
1.3 Creep of structural wood adhesives as measured by this test method may not be comparative to other ASTM methods and is limited to the conditions of the test and procedures contained herein.  
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM D5649-15(2023)(Test Method)
Standard Test Method for Torque Strength of Adhesives Used on Threaded Fasteners

SIGNIFICANCE AND USE
5.1 This test method provides reasonably accurate information with regard to the determination of the securing or locking effect of adhesives used in threaded fasteners. This test method may also be used to determine the degree of cure and the effect of environment on torque strength.  
5.2 The accuracy of the test results depends to a large degree on the thread clearance of the test fasteners and the inclusion of air bubbles in the bond line. Data generated by this test method should be safety-factored accordingly if used as quality assurance acceptance or rejection.
SCOPE
1.1 This test method is used to make comparative assessments of the securing or locking effect of adhesives used in threaded assemblies.  
1.2 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D3929-03(2023)(Test Method)
Standard Test Method for Evaluating Stress Cracking of Plastics by Adhesives Using the Bent-Beam Method

SIGNIFICANCE AND USE
5.1 This test method is designed for obtaining a qualitative estimate of the compatibility of plastics and adhesives. Due to the many process variables associated with the fabrication of plastic parts, it is not possible to use this test as a substitute for compatibility tests on actual parts.  
5.2 The detection of cracks or crazes may be determined with or without optical aid. Make comparisons only among tests employing crack detection methods of equivalent sensitivity.
SCOPE
1.1 This test method describes a procedure for determining the compatibility of adhesives with plastics based on whether the adhesive causes cracking of stressed samples.  
1.2 Specimen configurations and test fixture designs are given.  
1.3 This test method is suitable for products in the form of sheet or strip. It can also be used on injection molded tensile specimens or flexural bars.  
1.4 The values stated in SI units are to be regarded as the standard. The inch-pound units given in parentheses are for information only.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D4800-94(2023)(Guide)
Standard Guide for Classifying and Specifying Adhesives

SIGNIFICANCE AND USE
4.1 The purpose of this classification system is to provide a method of identifying adhesives in order to give industry a system that can be used universally for materials. It further provides a means for specifying these materials by the use of the standards that are developed using this guide.  
4.2 This classification system was developed to permit the addition of future adhesives.
SCOPE
1.1 This guide provides a classification system for tabulating the properties of adhesives suitable for holding parts or assemblies together. The use of this guide also provides information necessary for the development of standard specifications for adhesives.  
Note 1: This classification system may serve many of the needs of industries using adhesives. This guide is subject to revision as the need requires; therefore, the latest revision should always be used.  
1.2 Limitations—This classification system is intended to be a means of identifying adhesives. It is not intended for the selection of materials. Material selection should be made by those having expertise in the adhesives field after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the attachment process to be employed, the inherent properties of the material not covered in this document, and the economic factors.  
1.3 This classification system is based on the premise that adhesives can be arranged into broad generic families using basic properties to arrange the materials into groups, classes, and grades.  
1.4 In all cases where the provisions of this classification system would conflict with the referenced ASTM specification for a particular material, the latter shall take precedence.  
1.5 The values stated in SI units, as detailed in IEEE/ASTM SI 10, are to be regarded as the standard.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    4 pages
    English language
    sale 15% off
ASTM
ASTM D2851-15(2023)(Specification)
Standard Specification for Liquid Optical Adhesive

ABSTRACT
This specification covers liquid optical adhesive for use in bonding glass to glass or other transparent adherends. The adhesive shall be in liquid form and free of solvent in order to avoid bubble formation in the adhesive layer. Each component shall be completely reactive. The adhesive may be heat-, catalyst-, or radiation-cured. Voltatility, color, viscosity, foreign particle content, refractive index, stability, light transmission, glass doublet preparation, environmental test, and bond strength tests shall be performed in accordance with the specified requirements.
SCOPE
1.1 This specification covers liquid optical adhesive for use in bonding glass to glass or other transparent adherends.  
1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are provided for information purposes only.  
1.3 The following precautionary caveat pertains only to the test method portion, Section 6, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in 6.1.1.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM D4300-23(Test Method)
Standard Test Methods for Ability of Adhesive Films to Support or Resist the Growth of Fungi

SIGNIFICANCE AND USE
4.1 These test methods are designed to be used to determine the susceptibility of the adhesive film to biodegradation and whether the adhesive will carry into the bond line sufficient anti-fungal properties to prevent growth of fungi frequently present on the gluing equipment, on adherends, or in the adhesive as applied.  
4.2 Potato dextrose agar (PDA) provides a complete medium for the growth of fungi, while mineral salts agar (MSA) lacks a carbohydrate source and provides a less favorable medium. Use of PDA tests the adhesive film for its ability to resist the growth of fungi on its surface as well as its ability to repel a copious growth of fungi on the adjacent agar surface. Use of MSA tests the adhesive film primarily for its ability to resist the growth of fungi on its surface. When it is used, there is a reduced possibility that the growth from the agar will be mis-read as coming from the adhesive film, since fungal growth on the adjacent agar will be scant.
Note 2: The method given here using the MSA is based on Practice G21, adapted to be used with adhesives. Requirements for the use of the MSA are described in 10.2, and a mixed species of fungi is prescribed in 8.2 for the inoculum.  
4.3 The results obtained when using the procedures given in this method apply only to the species used for the testing. The test species listed in Section 8 are frequently used by laboratories to test for antifungal properties, but they are not the only ones which could be used. Selection of the fungal species to test against requires informed judgment by the testing laboratory or by the party requesting the tests. These methods are especially useful when species that have been isolated from contaminated adhesives are used as the test species (see Section 8) to aid in the selection of more effective fungicides.  
4.4 The efficacy of some biocides may change in storage due to the chemical and thermal environment to which they are subjected as components of certain adhesi...
SCOPE
1.1 These test methods test the ability of adhesive films to inhibit or support the growth of selected fungal species growing on agar plates by providing means of testing the films on two agar substrates, one which promotes microbial growth, and one which does not.  
1.2 These test methods are not appropriate for all adhesives. The activity of certain biocides may not be demonstrated by these test methods as a result of irreversible reaction with some of the medium constituents.  
Note 1: As an example, quaternary ammonium compounds are inactivated by agar.  
1.3 A test method is included for use with low-viscosity adhesives along with an alternative method for use with mastic-type adhesives.  
1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. These test methods are designed to be used by persons trained in correct microbiological techniques. Specific precautionary statements are given in Section 7 and in 14.3.2.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    9 pages
    English language
    sale 15% off
  • Standard
    9 pages
    English language
    sale 15% off
ASTM
ASTM D4317-16(2023)(Specification)
Standard Specification for Polyvinyl Acetate-Based Emulsion Adhesives

ABSTRACT
This specification covers polyvinyl acetate or polyvinyl acetate copolymer resin emulsion adhesives suitable for use on wood, wood-based substrates, or plastic laminates. This does not cover the group of polyvinyl-based adhesives suitable for bonding flexible films. Adhesives are classified on the basis of water resistance at three performance levels, namely wet-use (Type 1), intermediate use (Type 2), and dry-use (Type 3). Adhesives shall conform to test requirements as performed under the following exposure conditions and treatments: dry shear at specified temperatures; two-cycle boil; 48-hour soak; humidity exposure; freeze-thaw stability; and storage life. Materials shall also adhere to physical properties such as density, nonvolatile matter, and pH.
SCOPE
1.1 This specification covers polyvinyl acetate or polyvinyl acetate copolymer resin emulsion adhesives suitable for use on wood, wood-based substrates, or plastic laminates. It does not cover the group of polyvinyl-based adhesives which are suitable for bonding flexible films.  
1.2 The adhesives are classified at three performance levels in accordance with water-resistance as shown in Table 1 and Table 2. See Section 5 for a description of the expected exposure conditions for each class of adhesive. See Table X1.1 for a classification of typical end products that are manufactured using adhesives at the three performance levels covered by this specification.    
1.3 The following index is provided as a guide to the test methods portion of this specification:    
Section  
Tests for Physical Properties  
9  
Viscosity  
9.1.1  
Density  
9.1.2  
Nonvolatiles  
9.1.3  
pH  
9.1.4  
Tests for Adhesive Bond  
10  
Block Shear Strength, Compression  
10.2  
Plywood Shear Tests  
10.3  
1.4 The values stated in SI units are to be regarded as the standard. The values given in parenthesis are for information purposes only.  
1.5 The following safety hazards caveat pertains only to the test method portion, Sections 9 and 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    6 pages
    English language
    sale 15% off
ASTM
ASTM D1876-08(2023)(Test Method)
Standard Test Method for Peel Resistance of Adhesives (T-Peel Test)

ABSTRACT
This test method is primarily intended for determining the relative peel resistance of adhesive bonds between flexible adherends by means of a T-type specimen using a tension testing machine. The bent, unbonded ends of the test specimen shall be clamped in the test grips of the tension testing machine and a load of a constant head speed shall be applied. An autographic recording of the load versus the head movement or load versus distance peeled shall be made. The peel resistance over a specified length of the bond line after the initial peak shall be determined.
SCOPE
1.1 This test method is primarily intended for determining the relative peel resistance of adhesive bonds between flexible adherends by means of a T-type specimen.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are provided for information purposes only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D3930-08(2023)(Specification)
Standard Specification for Adhesives for Wood-Based Materials for Construction of Manufactured Homes

ABSTRACT
This specification provides the means to measure and evaluate the performance of adhesives for structural or semistructural bonding of wood-to-wood in manufactured homes. Wood as used in this specification includes lumber, plywood, particleboard, gypsum board, and all materials having woodbased surfaces at the bondline. The adhesives can be classified according to resistance to deformation: Group A or structural, and Group B or semistructural. Also, the adhesives may be designated into three types, according to their recommended use based on their resistance to water and water vapor: Type 1 for interior and exterior use, Type 2 for weather-protected interior use, and Type 3 for interior use only. Different tests shall be performed in order to determine the following properties of adhesives: shear strength, gap-filling ability, total deformation resistance, moisture and temperature limitation during fabrication, high-temperature resistance, low-temperature resistance, moisture resistance, aging, oxidation resistance, and mold resistance.
SCOPE
1.1 This specification provides the means to measure and evaluate the performance of adhesives for structural or semi-structural bonding of wood-to-wood in manufactured homes. Wood as used in this specification includes lumber, plywood, particleboard, gypsum board, and all materials having wood-based surfaces at the bondline. This specification does not cover other adhesives used in manufactured homes such as adhesives for carpet, floor tile, ceramic fixtures, plastic laminates, trim and millwork, and similar nonstructural applications.  
1.1.1 The performance of the adhesives is measured in the following tests:    
Number  
Test  
Section  
1  
Low Temperature  
16  
2  
Dry Lumber  
17  
3  
Gap-Filling  
18  
4  
High Temperature  
19  
5  
Type 3 Qualification  
20  
6  
Type 2 Qualification  
21  
7  
Aging, Film Oxidation  
22  
8  
Aging, Bond Oxidation  
23  
9  
Resistance to Deformation, Creep  
24  
10  
Mold  
25  
11  
Type 1 Qualification  
26  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    19 pages
    English language
    sale 15% off
ASTM
ASTM D1062-08(2023)(Test Method)
Standard Test Method for Cleavage Strength of Metal-to-Metal Adhesive Bonds

ABSTRACT
This test method covers the determination of the comparative cleavage strength properties of metal-to-metal adhesive bonds. The testing machine shall be capable of maintaining the rate of loading and shall compose of fixed member, movable member, and grips. Test specimens shall consist of metal pieces glued together according to the prescribed dimensions indicated in this standard method. Recommended metal specimens are the following: brass, copper, aluminum, steel, and phosphor bronze. Bonding and conditioning of specimen shall be done according to the procedure specified by the manufacturer of the adhesive. Testing procedure shall be in accordance to the load rate limits specified in this standard method. Cleavage strength shall be expressed in pounds per inch and shall be reported in three significant figures in addition to the following information: adhesive identification, preparation method, adhesive layer thickness, conditioning procedure used, testing room condition, specimen number, and loading rate.
SCOPE
1.1 This test method covers the determination of the comparative cleavage properties of adhesive bonds when tested on standard shape metal specimens under specified conditions of preparation and testing. It may be used also to compare adhesives used with other metallic materials having any specified surface treatment.  
1.2 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off