Standard Specification for Plastic (Stucco) Cement

ABSTRACT
This specification covers plastic cements for use in Portland cement-based plasters for exterior (stucco) and interior applications. All the materials should be tested and conform to the required values of fineness, autoclave expansion, time of setting, compressive strength, air content of mortar, and water retention. The cement should be stored in a way that permits easy access and inside a suitable weathertight building.
SCOPE
1.1 This specification covers two types of plastic cement for use in portland cement-based plasters for exterior (stucco) and interior application.
1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Values in SI units shall be obtained by measurement in SI units or by appropriate conversion, using the Rules for Conversion and Rounding given in Standard , of measurements made in other units. Values are stated in only SI units when inch-pound units are not used in practice.
1.3 The text of this standard refers to notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.
1.4 The following safety hazards caveat pertains only to Sections 14 and 15. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. (WarningFresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and tissue upon prolonged exposure.)

General Information

Status
Historical
Publication Date
31-Mar-2012
Technical Committee
Drafting Committee
Current Stage
Ref Project

Relations

Buy Standard

Technical specification
ASTM C1328/C1328M-12 - Standard Specification for Plastic (Stucco) Cement
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview
Technical specification
REDLINE ASTM C1328/C1328M-12 - Standard Specification for Plastic (Stucco) Cement
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:C1328/C1328M −12
Standard Specification for
1
Plastic (Stucco) Cement
This standard is issued under the fixed designation C1328/C1328M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2. Referenced Documents
3
1.1 This specification covers two types of plastic cement for 2.1 ASTM Standards:
use in portland cement-based plasters for exterior (stucco) and C109/C109M Test Method for Compressive Strength of
Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube
interior application.
Specimens)
1.2 Units—The values stated in either SI units or inch-
C151 Test Method for Autoclave Expansion of Hydraulic
pound units are to be regarded separately as standard. The
Cement
values stated in each system may not be exact equivalents;
C183 Practice for Sampling and the Amount of Testing of
therefore,eachsystemshallbeusedindependentlyoftheother.
Hydraulic Cement
Combining values from the two systems may result in non-
C185 Test Method for Air Content of Hydraulic Cement
conformance with the standard. Values in SI units shall be
Mortar
obtained by measurement in SI units or by appropriate
C187 Test Method for Amount of Water Required for Nor-
conversion, using the Rules for Conversion and Rounding
mal Consistency of Hydraulic Cement Paste
given in Standard IEEE/ASTM SI 10, of measurements made
C188 Test Method for Density of Hydraulic Cement
in other units. Values are stated in only SI units when
C219 Terminology Relating to Hydraulic Cement
inch-pound units are not used in practice.
C266 Test Method for Time of Setting of Hydraulic-Cement
1.3 The text of this standard refers to notes and footnotes
Paste by Gillmore Needles
that provide explanatory material. These notes and footnotes
C305 Practice for Mechanical Mixing of Hydraulic Cement
(excluding those in tables and figures) shall not be considered
Pastes and Mortars of Plastic Consistency
as requirements of the standard.
C430 Test Method for Fineness of Hydraulic Cement by the
1.4 The following safety hazards caveat pertains only to 45-µm (No. 325) Sieve
C511 Specification for Mixing Rooms, Moist Cabinets,
Sections 14 and 15. This standard does not purport to address
Moist Rooms, and Water Storage Tanks Used in the
all of the safety concerns, if any, associated with its use. It is
Testing of Hydraulic Cements and Concretes
the responsibility of the user of this standard to establish
C778 Specification for Standard Sand
appropriate safety and health practices and determine the
C926 Specification for Application of Portland Cement-
applicability of regulatory limitations prior to use.
Based Plaster
(Warning— Fresh hydraulic cementitious mixtures are caustic
C1506 Test Method for Water Retention of Hydraulic
and may cause chemical burns to skin and tissue upon
2
Cement-Based Mortars and Plasters
prolonged exposure.)
IEEE/ASTM SI 10 Standard for Use of the International
1.5 This international standard was developed in accor-
System of Units (SI) (the Modernized Metric System)
dance with internationally recognized principles on standard-
ization established in the Decision on Principles for the
3. Terminology
Development of International Standards, Guides and Recom-
mendations issued by the World Trade Organization Technical
3.1 Definitions—Termsusedinthisspecificationaredefined
Barriers to Trade (TBT) Committee.
in Terminology C219 and Specification C926.
3.2 Definitions of Terms Specific to This Standard:
3.2.1 plastic cement—a hydraulic cement, primarily used in
1
portland cement-based plastering construction, consisting of a
This specification is under the jurisdiction of ASTM Committee C01 on
Cement and is the direct responsibility of Subcommittee C01.11 on Masonry
Cement.
Current edition approved April 1, 2012. Published May 2012. Originally
3
approved in 1996. Last previous edition approved in 2005 as C1328 – 05. DOI: For referenced ASTM standards, visit the ASTM website, www.astm.org, or
10.1520/C1328_C1328M-12. contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
2
Annual Book of ASTM Standards, Vol 04.01. See the section on Safety Standards volume information, refer to the standard’s Document Summary page on
Precautions in the Manual of Cement Testing. the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
C1328/C1328M−12
mixture of portland or blended hydraulic cement and plasticiz- 9. Autoclave Expansion
ingmaterials(suchaslimestoneorhydratedorhydrauliclime),
9.1 Determine the autoclave ex
...

This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:C1328–05 Designation: C1328/C1328M – 12
Standard Specification for
1
Plastic (Stucco) Cement
This standard is issued under the fixed designation C1328/C1328M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers two types of plastic cement for use in portland cement-based plasters for exterior (stucco) and
interior application.
1.2The values stated in SI units are to be regarded as the standard. Values in SI units shall be obtained by measurement in SI
units or by appropriate conversion, using the Rules for Conversion and Rounding given in
1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated
in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values
from the two systems may result in non-conformance with the standard. Values in SI units shall be obtained by measurement in
SI units or by appropriate conversion, using the Rules for Conversion and Rounding given in Standard IEEE/ASTM SI 10, of
measurements made in other units. , of measurements made in other units.Values are stated in only SI units when inch-pound units
are not used in practice.
1.3 The text of this standard refers to notes and footnotes that provide explanatory material. These notes and footnotes
(excluding those in tables and figures) shall not be considered as requirements of the standard.
1.4 The following safety hazards caveat pertains only to Sections 14 and 15. This standard does not purport to address all of
the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety
and health practices and determine the applicability of regulatory limitations prior to use. (Warning— Fresh hydraulic
2
cementitious mixtures are caustic and may cause chemical burns to skin and tissue upon prolonged exposure.)
2. Referenced Documents
3
2.1 ASTM Standards:
C109/C109M Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens)
C151 Test Method for Autoclave Expansion of Hydraulic Cement
C183 Practice for Sampling and the Amount of Testing of Hydraulic Cement
C185 Test Method for Air Content of Hydraulic Cement Mortar
C187 Test Method for Amount of Water Required for Normal Consistency of Hydraulic Cement Paste
C188 Test Method for Density of Hydraulic Cement
C219 Terminology Relating to Hydraulic Cement
C266 Test Method for Time of Setting of Hydraulic-Cement Paste by Gillmore Needles
C305 Practice for Mechanical Mixing of Hydraulic Cement Pastes and Mortars of Plastic Consistency
C430 Test Method for Fineness of Hydraulic Cement by the 45-m (No. 325) Sieve
C511 Specification for Mixing Rooms, Moist Cabinets, Moist Rooms, and Water Storage Tanks Used in the Testing of
Hydraulic Cements and Concretes
C778 Specification for Sand
C926 Specification for Application of Portland Cement-Based Plaster
C1506 Test Method for Water Retention of Hydraulic Cement-Based Mortars and Plasters
IEEE/ASTM SI 10 Standard for Use of the International System of Units (SI) (the Modernized Metric System)
1
This specification is under the jurisdiction of ASTM Committee C01 on Cement and is the direct responsibility of Subcommittee C01.11 on Masonry Cement.
Current edition approved Sept. 15, 2005. Published October 2005. Originally approved in 1996. Last previous edition approved in 2003 as C1328–03a. DOI:
10.1520/C1328-05.
Current edition approved April 1, 2012. Published May 2012. Originally approved in 1996. Last previous edition approved in 2005 as C1328 – 05. DOI:
10.1520/C1328_C1328M-12.
2
Annual Book of ASTM Standards, Vol 04.01. See the section on Safety Precautions in the Manual of Cement Testing.
3
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
C1328/C1328M – 12
3. Terminology
3.1 Definitions—Terms used in this specification are
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.