ASTM D3018/D3018M-11

Standard Specification for Class A Asphalt Shingles Surfaced with Mineral Granules

ABSTRACT
This specification covers mineral granule-surfaced asphalt roofing shingles. Covered here are the self-sealing (Type I) and non-self-sealing (Type II) types of shingles. The shingles shall consist of organic felt or glass mat(s) saturated or impregnated, and coated on both sides with a hot asphaltic material and completely surfaced on the weather side with mineral granules embedded in the coating. The reverse side of the shingles shall be covered with a suitable material to prevent the shingles from sticking together in the package, causing possible damage upon being unpacked at ambient temperatures. Type I shingles shall have a factory-applied adhesive that will seal the shingles together after application. Both types shall meet the conditions for Class A fire exposure, and loss and behaviour on heating tests. Type I shingles shall pass an additional wind resistance test.
SCOPE
1.1 This specification covers granule-surfaced asphalt roofing shingles that meet the requirements for Class A fire test, behavior on heating, and wind testing.
1.2 Shingles meeting this specification are intended to be applied with a headlap of not less than 51 mm [2 in.].
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

General Information

• Status: Historical
• Publication Date: 31-May-2011
• ICS: 91.100.15 - Mineral materials and products
• Technical Committee: D08 - Roofing and Waterproofing
• Drafting Committee: D08.02 - Steep Roofing Products and Assemblies

Relations

• Replaces: ASTM D3018/D3018M-10a - Standard Specification for Class A Asphalt Shingles Surfaced with Mineral Granules
• Effective Date: 01-Jun-2011

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D3018/D3018M −11
Standard Specification for
1
Class AAsphalt Shingles Surfaced with Mineral Granules
This standard is issued under the fixed designation D3018/D3018M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 4.1.1 Type I—Self-sealing.
4.1.2 Type II—Non-self-sealing.
1.1 This specification covers granule-surfaced asphalt roof-
ing shingles that meet the requirements for Class A fire test,
5. Materials and Manufacture
behavior on heating, and wind testing.
5.1 The shingles covered by this specification shall consist
1.2 Shingles meeting this specification are intended to be
of organic felt or glass mat(s) saturated or impregnated and
applied with a headlap of not less than 51 mm [2 in.].
coated on both sides with a hot asphaltic material.All surfaces
1.3 The values stated in either SI units or inch-pound units
intended to be exposed to the weather, including any cutouts or
are to be regarded separately as standard. The values stated in
other separations, when the product is applied in accordance
each system may not be exact equivalents; therefore, each
with the manufacturers’/sellers’ instructions, shall be surfaced
system shall be used independently of the other. Combining
with mineral granules embedded in the asphalt coating.
values from the two systems may result in non-conformance
5.2 Thehotasphalticmaterialusedtosaturateorimpregnate
with the standard.
and coat the organic felt or glass mat(s) may be compounded
2. Referenced Documents
with a mineral stabilizer.
2
2.1 ASTM Standards:
5.3 The reverse side of the shingles shall be covered with a
D228 Test Methods for Sampling, Testing, and Analysis of
suitable material to prevent the shingles from sticking together
Asphalt Roll Roofing, Cap Sheets, and Shingles Used in
in the package.
Roofing and Waterproofing
5.4 Type I shingles shall have a factory-applied adhesive
D1079 Terminology Relating to Roofing and Waterproofing
that will seal the shingles together after application.
D3161 Test Method for Wind-Resistance of Asphalt
Shingles (Fan-Induced Method)
6. Physical Requirements
E108 Test Methods for Fire Tests of Roof Coverings
6.1 Shingles shall not stick together in the package so as to
3. Terminology
cause damage upon being unpacked at ambient temperatures
above 10° C [50°F].
3.1 Definitions:
3.1.1 glass mat—for testing purposes in accordance with
6.2 Loss and Behavior on Heating—There shall be not more
Test Methods D228, glass mat shall be considered as felt.
than 1.5 % average loss of volatile matter, and the granular
1
3.2 For definitions of terms used in this specification, see surfacing shall not slide more than 2 mm [ ⁄16 in.].
Terminology D1079.
6.3 Fire Test Classification—Shingles shall pass all of the
Class A fire exposure tests.
4. Classification
6.4 Wind Resistance—Shingles shall be classified in accor-
4.1 Asphalt shingles covered by this specification are of two
dance with the wind-resistance test (see 9.1.3).
types:
7. Dimensions and Permissible Variations
1
This specification is under the jurisdiction of ASTM Committee D08 on
7.1 The form and size of the shingles shall be as agreed
Roofing and Waterproofing and is the direct responsibility of Subcommittee D08.02
on Steep Roofing Products and Assemblies.
upon by the purchaser and seller.
Current edition approved June 1, 2011. Published June 2011. Originally
7.2 The shingles shall not vary in length more than 63.2
approved in 1972. Last previous edition approved in 2010 as D3018 – 10a. DOI:
1
10.1520/D3018_D3018M-11.
mm [ ⁄8 in.] from nominal dimensions established for each size,
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
except that the length of shingles without cutouts shall not vary
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
1
morethan 66.4mm[ ⁄4in.].Thewidthoftheshinglesshallnot
Standards volume information, refer to the standard’s Document Summary page on
1
the ASTM website. vary more than 66.4 mm [ ⁄4 in.].
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D3018/D3018M − 11
8. Workmanship, Finish, and Appearance 10. Inspection
10.1 Inspection of material shall be made as agreed upon by
8.1 The organic felt or glass mat(s) shall be uniformly
the purchaser and the seller as part of the purchase contract.
saturated or impregnated with asphalt and shall show no
untreated spots at any point upon cutting 50-mm [2-in.] wide
11. Rejection and Resubmittal
strips at random across the entire w
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:D3018/D3018M–10a Designation: D3018/D3018M – 11
Standard Specification for
1
Class A Asphalt Shingles Surfaced with Mineral Granules
This standard is issued under the fixed designation D3018/D3018M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope
1.1 This specification covers granule-surfaced asphalt roofing shingles that meet the requirements for ClassAfire test, behavior
on heating, and wind testing.
1.2 Shingles meeting this specification are intended to be applied with a headlap of not less than 51 mm [2 in.].
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in non-conformance with the standard.
2. Referenced Documents
2
2.1 ASTM Standards:
D228 Test Methods for Sampling, Testing, and Analysis of Asphalt Roll Roofing, Cap Sheets, and Shingles Used in Roofing
and Waterproofing
D1079 Terminology Relating to Roofing and Waterproofing
D3161 Test Method for Wind-Resistance of Asphalt Shingles (Fan-Induced Method)
E108 Test Methods for Fire Tests of Roof Coverings
3. Terminology
3.1 Definition:
3.1.1 glass mat—for testing purposes in accordance with Test Methods D228, glass mat shall be considered as felt.
3.2 For definitions of terms used in this specification, see Terminology D1079.
4. Classification
4.1 Asphalt shingles covered by this specification are of two types:
4.1.1 Type I—Self-sealing.
4.1.2 Type II—Non-self-sealing.
5. Materials and Manufacture
5.1The shingles covered by this specification shall consist of organic felt or glass mat(s) saturated or impregnated and coated
on both sides with a hot asphaltic material and completely surfaced on the weather side with mineral granules embedded in the
coating.
5.1 The shingles covered by this specification shall consist of organic felt or glass mat(s) saturated or impregnated and coated
on both sides with a hot asphaltic material. All surfaces intended to be exposed to the weather, including any cutouts or other
separations, when the product is applied in accordance with the manufacturers’/sellers’instructions, shall be surfaced with mineral
granules embedded in the asphalt coating.
5.2 The hot asphaltic material used to saturate or impregnate and coat the organic felt or glass mat(s) may be compounded with
a mineral stabilizer.
5.3 The reverse side of the shingles shall be covered with a suitable material to prevent the shingles from sticking together in
the package.
1
This specification is under the jurisdiction of ASTM Committee D08 on Roofing and Waterproofing and is the direct responsibility of Subcommittee D08.02 on Steep
Roofing Products and Assemblies.
Current edition approvedAug.June 1, 2010.2011. PublishedAugust 2010.June 2011. Originally approved in 1972. Last previous edition approved in 2010 as D3018 – 10a.
DOI: 10.1520/D3018_D3018M-10A1.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D3018/D3018M – 11
5.4 Type I shingles shall have a factory-applied adhesive that will seal the shingles together after application.
6. Physical Requirements
6.1 Shingles shall not stick together in the package so as to cause damage upon being unpacked at ambient temperatures above
10° C [50°F].
6.2 Loss and Behavior on Heating—There shall be not more than 1.5 % average loss of volatile matter, and the granular
1
surfacing shall not slide more than 2 mm [ ⁄16 in.].
6.3 Fire Test Classification—Shingles shall pass all of the Class A fire exposure tests.
6.4 Wind Resistance—Shingles shall be classified in accordance with the wind-resistance test (see 9.1.3).
7. Dimensions and Permissible Variations
7.1 The form and size of the shingles shall be as agreed upon by the purchaser and seller.
1
7.2 The shingles shall
...