iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D2198-02

(Test Method)

Standard Test Method for Stain Removal From Multicolor Lacquers (Withdrawn 2003)

Standard Test Method for Stain Removal From Multicolor Lacquers (Withdrawn 2003)

SCOPE
1.1 This test method covers a procedure for the removal of pencil, crayon, and grease stains from multicolor lacquer films that have been applied to primed steel panels.
Note 1—Due to the nature of the test, comparable results can be obtained only when exactly the same materials and apparatus are used. In this test method it has not been found possible to describe the materials and apparatus adequately in more than general terms.
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Withdrawn
Publication Date
09-May-2002
Withdrawal Date
28-Feb-2003
ICS
87.040 - Paints and varnishes
Technical Committee
D01 - Paint and Related Coatings, Materials, and Applications
Drafting Committee
D01.55 - Factory Applied Coatings on Preformed Products
Current Stage
Ref Project

Relations

Replaces
ASTM D2198-84(1996)e1 - Standard Test Method for Stain Removal From Multicolor Lacquers
Effective Date
10-May-2002

Buy Standard

ASTM D2198-02 - Standard Test Method for Stain Removal From Multicolor Lacquers (Withdrawn 2003)ASTM D2198-02 - Standard Test Method for Stain Removal From Multicolor Lacquers (Withdrawn 2003)
PreviousNext
Standard
ASTM D2198-02 - Standard Test Method for Stain Removal From Multicolor Lacquers (Withdrawn 2003)
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superceded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
Designation: D 2198 – 02
Standard Test Method for
1
Stain Removal From Multicolor Lacquers
This standard is issued under the fixed designation D 2198; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope Fed. Spec. VV-P-236 Specification for Petrolatum
6
2.3 U. S. Military Specification:
1.1 This test method covers a procedure for the removal of
MIL-P-11414A Specification for Primer Coating, Lacquer,
pencil, crayon, and grease stains from multicolor lacquer films
Rust Inhibiting
that have been applied to primed steel panels.
NOTE 1—Due to the nature of the test, comparable results can be 3. Summary of Test Method
obtained only when exactly the same materials and apparatus are used. In
1
3.1 Three 165 by 430 mm (6 ⁄2 by 17 in.) primed steel
this test method it has not been found possible to describe the materials
panels are sprayed with multicolor lacquer and allowed to dry
and apparatus adequately in more than general terms.
for 24 h. Varnish is then applied to the ends of the panels and
1.2 The values stated in SI units are to be regarded as the
allowed to dry 72 h. The three stains are applied by a
standard. The values given in parentheses are for information
mechanical apparatus and removed by washing.
only.
1.3 This standard does not purport to address all of the 4. Significance and Use
safety concerns, if any, associated with its use. It is the
4.1 The procedure described in this test method is intended
responsibility of the user of this standard to establish appro-
as an aid in evaluating the ease of removal for surface stains
priate safety and health practices and determine the applica-
encountered by surfaces coated with multicolor lacquers.
bility of regulatory limitations prior to use.
5. Apparatus and Materials
2. Referenced Documents
1
5.1 Steel Panels, 165 by 430 mm (6 ⁄2 by 17 in.), 20-gage
2.1 ASTM Standards:
cold-rolled steel conforming to Specification A 109 or Speci-
A 109 Specification for Steel, Strip, Carbon (0.25 Maxi-
fication A 366/A 366M.
2
7
mum Percent), Cold-Rolled
5.2 Washability Machine, The washability machine should
A 366/A 366M Specification for Commercial Steel (CS),
be capable of moving the abrasion boat linearly across the
Sheet, Carbon (0.15 Maximum Percent), Cold-Rolled,
sample with a reciprocating motion. The speed should be 37 6
3
Commercial Quality
1 cycles (double strokes) per minute over a 10 in. travel.
4
D 209 Specification for Lampblack Pigment
5.3 Lacquer Primer, conforming to MIL-P-11414A.
D 609 Practice for Preparation of Cold-Rolled Steel Panels
5.4 Drafting Pencil.
for Testing Paint, Varnish, Conversion Coatings, and
5.5 China Marking Crayon.
5
Related Coating Products 8
5.6 Wetting Agent.
6
2.2 U. S. Federal Specifications: 9
5.7 Silica.
Fed. Spec. EE-0-451C Specification for Oleo (Margarine)
5.8 Diaper Cloth.
Fed. Spec. TTV-121C Specification for Varnish, Spar, Water
5.9 Varnish, clear and waterproof, conforming to Fed. Spec.
Resisting
TT-V-121C or equal cut in mineral spirits.
Fed. Spec. VV-0-551 Specification for Oil, Lubricating,
5.10 Carriage, for mounting pencil and crayon.
Marine and Engine, Mineral
5.11 Arm, extendible, for mounting mohair roller.
1
5.12 Mohair Roller,40mm(1 ⁄2 in.), for application of
1 grease stain.
This test method is under the jurisdiction of ASTM Committee D01 on Paint
and Related Coatings, Materials, and Applications and is the direct responsibility of 5.13 Glass Plate, 100 by 175 mm (4 by 7 in.), for holding
Subcommittee D01.55 on Factory Applied Coatings on Preformed Products.
grease stain.
Current edition approved May 10, 2002. Published July 2002. Originally
{1
published as D 2198 – 63 T. Last previous edition D 2198 – 84 (1996) .
2 7
Annual Book of ASTM Standards, Vol 01.03. A list of machines suitable for this purpose is found in supporting data available
3
Discontinued; see Annual Book of ASTM Standards, Vol 01.03. from ASTM International Headquarters. Request RR: D01–1124.
4 8
Annual Book of ASTM Standards, Vol 06.03. Triton X-100, available from Dow Chemical, 2040 Dow Center, Midland, MI
5
Annual Book of ASTM Standards, Vol 06.01. 48674, has been found suitable for this purpose.
6 9
Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, A list of silicas suitable for this purpose is found in supporting data available
Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098. from ASTM International Headquarters. Request RR: D01–1125.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 --------------
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D16-23(Terminology)
Standard Terminology for Paint, Related Coatings, Materials, and Applications

SCOPE
1.1 This standard consists of technical terms used in standards under the jurisdiction of ASTM Committee D01 (on Paint and Related Coatings, Materials, and Applications), and of definitions suitable for use in these standards.
Note 1: When any definition in this standards is quoted or published out of the context of this standard, editorially insert the following delimiting statement “for paints and related coatings, materials, and applications” after the dash following the term (in the absence of an existing delimiting statement). This will limit the filed of application of the term and definition to that approved by this committee.  
1.2 In this terminology standard, definitions used in other ASTM standards are indicated by following the definition with the designation of that standard. In some cases, a relevant D01 subcommittee is also listed. Definitions influenced by those used by other organizations are indicated by the acronym of the organization. Primary terms are given in bold, while narrower and unapproved terms are given in italics.  
1.3 There are several specialized terminology standards under the jurisdiction of Committee D01, as follows: D804, D1695, D6440, D6488, and D7188. Few definitions from those standards are included in Terminology D16. Therefore, in searches for definitions of paints and coatings terms, these standards should be included where appropriate.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    10 pages
    English language
    sale 15% off
  • Standard
    10 pages
    English language
    sale 15% off
ASTM
ASTM D2805-11(2023)(Test Method)
Standard Test Method for Hiding Power of Paints by Reflectometry

SIGNIFICANCE AND USE
5.1 This is a precise instrumental method giving results having an absolute physical significance without reference to a comparison paint. It should be used when maximum precision and minimum subjectivity are required, as in testing specification coatings or evaluating the hiding efficiency of pigments.  
5.2 Hiding power Test Method D344 is visual instead of instrumental, and gives results that are relative to a material standard instead of absolute. It is less precise than Test Method D2805 but more closely aligned with practical painting procedures.
SCOPE
1.1 This test method covers the determination, without reference to a material paint standard, of the hiding power of air dry coatings with Y tristimulus values greater than 15 %. With appropriate modification, it can also be used to test baking finishes.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM D6762-18(2023)(Test Method)
Standard Test Method for Determining the Hiding Power of Paint by Visual Evaluation of Spray Applied Coatings

SIGNIFICANCE AND USE
5.1 This test method determines hiding power of a test paint by visual evaluation of a spray applied coating.
Note 1: Test Method D2805 describes an instrumental method for determining hiding power. The paint film is applied at a uniform thickness (for example with a doctor blade), the film thickness is measured rigorously, and the opacity is determined photometrically. Hiding power is thereby determined with a high degree of precision.  
5.2 Test Method D6762 is less precise than Test Method D2805, but is commonly used since it is more closely related to the application characteristics of the paint and is simpler in concept and evaluation.
SCOPE
1.1 This test method provides for the quantitative visual determination of the film thickness required to achieve full hiding. This film thickness is considered to be the hiding power of a test paint.  
1.2 This method applies only to spray applied coatings but its concepts are valid for other methods of application as well.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D3732-23(Practice)
Standard Practice for Reporting Cure Times of Ultraviolet-Cured Coatings

SIGNIFICANCE AND USE
4.1 This practice provides a guide whereby all pertinent variables relating to the ultraviolet cure of a coating are described.
SCOPE
1.1 This practice applies to all coatings cured by ultraviolet energy.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D3322-23(Practice)
Standard Practice for Testing Primers and Primer Surfacers Over Preformed Metal

SIGNIFICANCE AND USE
4.1 Primers and primer surfacers may be used over many different surfaces top coated with one or more of a variety of coatings and subjected to many kinds of wear and exposure.  
4.2 The selection of the tests to be used for any given product or system must be governed by experience and by the requirement agreed upon between the producer and the user.
SCOPE
1.1 This practice covers the selection and use of procedures for testing primers and primer surfacers.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D6486-23(Practice)
Standard Practice for Short Term Vehicle Service Exposure of Automotive Coatings

SIGNIFICANCE AND USE
4.1 Since the exposure of automotive coatings to the various mechanical and chemical stresses encountered in actual operations, is very opportunistic, obtaining statistically significant data from which valid conclusions can be drawn, requires rigorous attention to the experimental designs and conditions of exposure.
SCOPE
1.1 This practice covers the protocol for vehicle service exposure testing of automotive coatings. Such exposure testing is valuable for the verification of the performance of automotive coatings and correlation with laboratory test data. Vehicle service exposure is intended to provide short term (2 to 20 weeks) exposure to the stress factors associated with vehicle operation. Factors included are scratch, mar, impact, stone chipping, insect impact, bird dropping, tree sap and staining, environmental fallout, etc.
Note 1: Vehicle service exposure is not intended to provide the conditions that are needed for characterizing the long term effects of weathering or corrosion exposure.  
1.2 The exposure conditions are produced by the placement of multiple test panels of automotive finishes on automotive test fleets that traverse a defined road course. Exposure to the operating environment can be 20 h/day, 7 days/week allowing for accumulation of over 100 000 miles in 10 weeks of exposure.  
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D1644-01(2023)(Test Method)
Standard Test Methods for Nonvolatile Content of Varnishes

SIGNIFICANCE AND USE
2.1 These test methods are applicable to varnish and are useful to producers and users in determining nonvolatile content and are sometimes an appropriate measure of the film-forming matter in varnish.
SCOPE
1.1 These test methods determine the fraction of a varnish that is nonvolatile at the temperature of the test while volatile solvents are driven off. It is sometimes an approximate measure of the film-forming matter in a varnish.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For a specific statement, see Section 3.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D713-23(Practice)
Standard Practice for Conducting Road Service Tests on Fluid Traffic Marking Materials

SIGNIFICANCE AND USE
3.1 This practice is an accelerated evaluation of bead retention, retroreflectivity, daytime color, night time color, and wear characteristics of fluid traffic marking materials. It is used to determine the useful life of such markings in the field. The same procedures are applicable to evaluating longitudinal lines to determine service life.
SCOPE
1.1 This practice covers the determination of the relative service life of fluid traffic marking materials such as paint, thermoplastic, epoxy, and polyester products under actual road conditions using transverse test lines. Materials under test are applied under prescribed conditions and periodic observations are made using prescribed performance criteria.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D1200-23(Test Method)
Standard Test Method for Viscosity by Ford Viscosity Cup

SIGNIFICANCE AND USE
5.1 This test method is useful for the determination of package and application viscosities of a number of paints and other coatings and in the thinning of these materials, but is limited to Newtonian or near-Newtonian liquids.  
5.2 There are other types of apparatus for measuring viscosity in the laboratory that produce more accurate results.
SCOPE
1.1 This test method covers the determination of the viscosity of Newtonian or near-Newtonian paints, varnishes, lacquers, and related liquid materials with the Ford-type efflux viscosity cup. If the material is non-Newtonian, that is, shear-thinning or thixotropic, Test Method D2196 should be used.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D711-23(Test Method)
Standard Test Method for No-Pick-Up Time of Pavement Markings

SIGNIFICANCE AND USE
3.1 This test method serves as a laboratory control test. Types of pavement markings that can be tested with this method are waterborne traffic paint, solvent borne traffic paint, and some two component 100 % solids liquid pavement markings, such as epoxy and modified epoxy pavement markings. If wet film thickness, temperature, and humidity are controlled within the tolerances specified herein, this method can be useful for relative testing of pavement markings and potentially for qualification of pavement markings for field application in approved specifications. For improved repeatability and meaningful comparison of pavement markings samples being tested, consistent air flow over the pavement marking films during testing is important. The buyer and seller should agree upon the air flow conditions, whether it be static or carefully regulated air flow (see 4.6.1 and 4.6.2). Because of the many variables operative in the field application of pavement markings (for example, wet film thickness, air temperature, humidity, wind speed, pavement type (asphalt or concrete), film profile over pavement, pavement temperature, pavement porosity, pavement moisture content, and the presence or absence of direct sunlight during striping), a direct correlation between the results of this test and field applications is difficult to obtain. However, relative field performance can be predicted using this method if the testing protocol is adhered to. For testing of two component 100 % solids liquid pavement markings an application of drop on retroreflective optics are typically applied at a specified rate to the markings prior to testing. For these types of pavement markings the regulation of air flow is not necessary due to the drying mechanics of the product.
SCOPE
1.1 This test method covers a laboratory procedure for determining the no-pick-up time of pavement markings. The method uses a wheel consisting of a metal cylinder with rubber O-rings. The wheel is rolled down a ramp over a freshly applied pavement marking film repeatedly until there is no transfer of the marking material to the rubber rings. The elapsed time from pavement marking film application to point of no marking material transfer is the no-pick-up time. Key variables to be controlled during testing are wet film thickness, temperature, humidity, air flow, and use of retroreflective optics. This standard provides three options for the testing of the no-pick-up time for pavement markings. The first option, Method A, specifies controls for temperature, humidity, and air flow during testing; a second option, Method B, specifies controls for temperature and humidity during testing, and a third option, Method C, provides guidance for performing this with a drop on application of retroreflective optics such as glass beads, Waterborne and Solvent Borne pavement markings are typically tested using Procedure A or Procedure B, without the application of drop on retroreflective optics. Pavement markings that are two component 100 % solids are typically tested using Method C.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    9 pages
    English language
    sale 15% off
  • Standard
    9 pages
    English language
    sale 15% off