ASTM E1977-01
(Specification)Standard Specification for Shelter, Tactical, Expandable, One-Side
Standard Specification for Shelter, Tactical, Expandable, One-Side
SCOPE
1.1 This specification covers a rigid wall, one-side expandable shelter constructed of aluminum-faced, nonmetallic honeycomb sandwich panels, and meeting the International Organization for Standardization (ISO) Cargo Container specification in the transport mode. Nominal dimensions when closed (container mode) are: height 8 ft, width 8 ft and length 20 ft (2.4 by 2.4 by 6.1 m). Approximate dimensions, when expanded (shelter mode) are: height 8 ft, width 15 ft and length 20 ft (2.4 by 4.6 by 6.1 m).
1.2 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only.
1.3 The following precautionary statement pertains to the test method portion only, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
Designation: E 1977 – 01
Standard Specification for
1
Shelter, Tactical, Expandable, One-Side
This standard is issued under the fixed designation E 1977; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
2
1. Scope with Polysulfide Based Sealants
E 1826 Specification for Low Volatile Organic (VOC)
1.1 This specification covers a rigid wall, one-side expand-
Corrosion-Inhibiting Adhesive Primer for Aluminum Al-
able shelter constructed of aluminum-faced, nonmetallic hon-
2
loys to Be Adhesively Bonded
eycomb sandwich panels, and meeting the International Orga-
E 1925 Specification for Engineering and Design Criteria
nization for Standardization (ISO) Cargo Container
2
for Rigid Wall Relocatable Structures
specification in the transport mode. Nominal dimensions when
3
2.2 ISO Standards:
closed (container mode) are: height 8 ft, width 8 ft and length
ISO 1161-1980 Series 1-Freight Containers-Corner Fittings,
20 ft. (2.4 by 2.4 by 6.1 m) Approximate dimensions, when
4
Specification
expanded (shelter mode) are: height 8 ft, width 15 ft and length
ISO 1496/I Series 1-Freight Containers-Specification and
20 ft (2.4 by 4.6 by 6.1 m).
4
Testing Part I-General Cargo Containers
1.2 The values stated in inch-pound units are to be regarded
5
2.3 Military Standards:
as the standard. The SI units given in parentheses are for
3
MIL-Q-9858 Quality Program Requirements
information only.
3
MIL-STD-129 Marking for Shipping and Storage
1.3 The following precautionary statement pertains to the
MIL-STD-810 Environmental Engineering Considerations
test method portion only. Section 7, of this specification; This
3
and Laboratory Tests
standard does not purport to address all of the safety concerns,
MIL-STD-1595 Qualification of Aircraft, Missile and Aero-
if any, associated with its use. It is the responsibility of the user
3
space Fusion Welders
of this standard to establish appropriate safety and health
3
MIL-STD-2219 Fusion Welding for Aerospace Appliances
practices and determines the applicability of regulatory limi-
2.4 ANSI/ASQC Standard:
tations prior to use.
ANSI/ASQC 21.4-1993 Sampling Procedures and Tables
5
2. Referenced Documents
for Inspection by Attributes
5-4-3200 Shelter, Assembly, One-Side Expandable-100
2.1 ASTM Standards:
6
amp
E 864 Practice for Surface Preparation of Aluminum Alloys
2
2.5 Drawings:
to Be Adhesively Bonded in Honeycomb Shelter Panels
5-4-2828 Shelter, Assembly, One-Side Expandable-60
E 865 Specification for Structural Film Adhesives for Hon-
6
2
amp
eycomb Sandwich Panels
E 866 Specification for Corrosion-Inhibiting Adhesive
3. General Requirements
Primer for Aluminum Alloys to Be Adhesively Bonded in
2
3.1 Alternate Components—When this specification or the
Honeycomb Shelter Panels
referenced drawings specify use of a specific component “or
E 874 Practice for Adhesive Bonding of Aluminum Facings
2
equal”, the contractor may substitute a component equal to the
to Nonmetallic Honeycomb Core for Shelter Panels
specified component provided that the contractor complies
E 990 Specification for Core-Splice Adhesive for Honey-
2
with the following requirements. Prior to manufacture of the
comb Sandwich Shelter Panels
first article, or if none is required, prior to commencing
E 1091 Specification for Nonmetallic Honeycomb Core for
2
production, the contractor shall submit for the purchaser’s
Use in Shelter Panels
approval a list identifying each proposed “or equal” component
E 1749 Terminology Relating to Rigid Wall Relocatable
2
Shelters
E 1773 Practice for Sealing Rigid Wall Tactical Shelters
3
Available from Standardization Documents Order Desk, Bldg. 4, Section D,
700 Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.
4
Available from American National Standards Institute, 11 W. 42nd St., 13th
1
This specification is under the jurisdiction of ASTM Committee E06 on Floor, New York, NY 10036.
5
Performance of Buildings and is the direct responsibility of Subcommittee E06.53 Available from American Society for Quality Control, 611 East Wisconsin
on Materials and Processes for Durable Rigidwall Relocatable Structures. Avenue, Milwaukee, WI 53201.
6
Current edition approved April 10, 2001. Published May 2001. Originally Copies of drawings are available from the U.S. Army Natick Research,
published as E 1977–98. Last previous edition E 1977–98. Development, and Engineering Center, Attn: SSCNC-WST, Natick, MA 07160-
2
Annual Book of ASTM Standards, Vol 04.11. 5018.
Copyright © ASTM, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 --------------------
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.