ASTM F1735-09
(Specification)Standard Specification for Poly (Vinyl Chloride)(PVC) Profile Strip for PVC Liners for Rehabilitation of Existing Man-Entry Sewers and Conduits
Standard Specification for Poly (Vinyl Chloride)(PVC) Profile Strip for PVC Liners for Rehabilitation of Existing Man-Entry Sewers and Conduits
ABSTRACT
This specification covers the requirements and test methods for materials, dimensions, workmanship, extrusion quality, and form of marking for extruded poly(vinyl chloride) (PVC) profile strips used for field fabrication of PVC liners for existing man-entry sewer and conduit rehabilitation. The strips shall be subjected to acetone immersion, elasticity, and hydrostatic pressure tests in the standard laboratory atmosphere under specific temperature and relative humidity conditions to determine conformance to extrusion quality, flexural rigidity, and joint leakage requirements, respectively. The extruded profile strips shall be homogeneous throughout and free from visible cracks, holes, foreign inclusions, or other injurious defects and shall be as uniform as commercially practical in color, opacity, density, and other physical properties.
SCOPE
1.1 This specification covers requirements and test methods for materials, dimensions, workmanship, extrusion quality, and a form of marking for extruded poly (vinyl chloride)(PVC) profile strips used for field fabrication of PVC liners for existing man-entry (36 to 144 in. (900 to 3650 mm) in vertical dimension) sewer and conduit rehabilitation.
1.2 Profile strip produced to this specification is for use in field fabrication of PVC liners in non-pressure pipe and conduit rehabilitation where the liner is installed into the existing sewer or conduit and the annular space between the liner and the existing sewer or conduit is grouted with cementitious grout.
Note 1—The practice for the installation of PVC liner covered by this specification is Practice F1698.
1.3 This specification includes extruded profile strips made only from materials specified in 6.1.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F1735 −09
StandardSpecification for
Poly (Vinyl Chloride)(PVC) Profile Strip for PVC Liners for
1
Rehabilitation of Existing Man-Entry Sewers and Conduits
This standard is issued under the fixed designation F1735; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* D883 Terminology Relating to Plastics
D1600 Terminology forAbbreviatedTerms Relating to Plas-
1.1 This specification covers requirements and test methods
tics
for materials, dimensions, workmanship, extrusion quality, and
D1784 Specification for Rigid Poly(Vinyl Chloride) (PVC)
a form of marking for extruded poly (vinyl chloride)(PVC)
Compounds and Chlorinated Poly(Vinyl Chloride)
profile strips used for field fabrication of PVC liners for
(CPVC) Compounds
existing man-entry (36 to 144 in. (900 to 3650 mm) in vertical
D2122 Test Method for Determining Dimensions of Ther-
dimension) sewer and conduit rehabilitation.
moplastic Pipe and Fittings
1.2 Profile strip produced to this specification is for use in
D2152 Test Method for Adequacy of Fusion of Extruded
fieldfabricationofPVClinersinnon-pressurepipeandconduit
Poly(Vinyl Chloride) (PVC) Pipe and Molded Fittings by
rehabilitationwherethelinerisinstalledintotheexistingsewer
Acetone Immersion
or conduit and the annular space between the liner and the
D2240 Test Method for Rubber Property—Durometer Hard-
existing sewer or conduit is grouted with cementitious grout.
ness
F412 Terminology Relating to Plastic Piping Systems
NOTE 1—The practice for the installation of PVC liner covered by this
specification is Practice F1698.
F1698 Practice for Installation of Poly(Vinyl Chlo-
ride)(PVC) Profile Strip Liner and Cementitious Grout for
1.3 This specification includes extruded profile strips made
Rehabilitation of Existing Man-Entry Sewers and Con-
only from materials specified in 6.1.
duits
1.4 The values stated in inch-pound units are to be regarded
2.2 Federal Standard:
as standard. The values given in parentheses are mathematical
Federal Standard No. 123 Marking For Shipment (Civil
conversions to SI units that are provided for information only
3
Agencies)
and are not considered standard.
2.3 Military Standard:
1.5 This standard does not purport to address all of the
3
MIL-STD-129 Marking for Shipment and Storage
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appro-
3. Terminology
priate safety and health practices and determine the applica-
3.1 General—Definitions are in accordance with Terminol-
bility of regulatory limitations prior to use.
ogy D883 and Terminology F412. Abbreviations are in accor-
2. Referenced Documents
dance with Terminology D1600, unless otherwise indicated.
2
2.1 ASTM Standards:
3.2 Definitions of Terms Specific to This Standard:
D618 Practice for Conditioning Plastics for Testing
3.2.1 See Fig. 1 to clarify terminology.
D790 Test Methods for Flexural Properties of Unreinforced
3.2.2 coextruded elastomer seal, n—a elastomer coextruded
and Reinforced Plastics and Electrical Insulating Materi-
in the joiner strip to provide compression sealing of the
als
mechanical joint made when the joiner strip locks adjacent
edges of former strip.
1
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
3.2.3 extruded PVC joiner strip, n—a companion product to
Piping Systems and is the direct responsibility of Subcommittee F17.67 on
the profile former strip of such configuration as to provide the
Trenchless Plastic Pipeline Technology.
Current edition approved Dec. 1, 2009. Published December 2009. Originally
locking mechanism at the edges of the former strips.
approved in 1996. Last previous edition approved in 2008 as F1735 - 02(2008).
DOI: 10.1520/F1735-09.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
3
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,
Standards volume information, refer to the standard’s Document Summary page on Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://
the ASTM website. www.dodssp.daps.mil.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F1735−09
2
FIG. 1An Example of A Profile PVC Strip
---------------------- Page: 2 ----------------------
F1735−09
NOTE 3—This is intended only for use as a quality control test and not
3.2.4 extruded PV
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
An American National Standard
Designation:F1735–02 (Reapproved 2008) Designation: F1735 – 09
Standard Specification for
Poly (Vinyl Chloride)(PVC) Profile Strip for PVC Liners for
1
Rehabilitation of Existing Man-Entry Sewers and Conduits
This standard is issued under the fixed designation F1735; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification covers requirements and test methods for materials, dimensions, workmanship, extrusion quality, and a
form of marking for extruded poly (vinyl chloride)(PVC) profile strips used for field fabrication of PVC liners for existing
man-entry (36 to 144 in. (900 to 3650 mm) in vertical dimension) sewer and conduit rehabilitation.
1.2 Profile strip produced to this specification is for use in field fabrication of PVC liners in non-pressure pipe and conduit
rehabilitation where the liner is installed into the existing sewer or conduit and the annular space between the liner and the existing
sewer or conduit is grouted with cementitious grout.
NOTE 1—The practice for the installation of PVC liner covered by this specification is Practice F1698.
1.3 This specification includes extruded profile strips made only from materials specified in 6.1.
1.4The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information
only.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D618 Practice for Conditioning Plastics for Testing
D790 Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
D883 Terminology Relating to Plastics
D1600 Terminology for Abbreviated Terms Relating to Plastics
D1784 Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC)
Compounds
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2152 Test Method for Adequacy of Fusion of Extruded Poly(Vinyl Chloride) (PVC) Pipe and Molded Fittings by Acetone
Immersion
D2240 Test Method for Rubber PropertyDurometer Hardness
F412 Terminology Relating to Plastic Piping Systems
F1698 Practice for Installation of Poly(Vinyl Chloride)(PVC) Profile Strip Liner and Cementitious Grout for Rehabilitation of
Existing Man-Entry Sewers and Conduits
2.2 Federal Standard:
3
Federal Standard No. 123 Marking For Shipment (Civil Agencies)
2.3 Military Standard:
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.67 on Trenchless
Plastic Pipeline Technology.
´1
Current edition approved March 1, 2008. Published June 2008. Originally approved in 1996. Last previous edition approved in 2002 as F1735-02 . DOI:
10.1520/F1735-02R08.
Current edition approved Dec. 1, 2009. Published December 2009. Originally approved in 1996. Last previous edition approved in 2008 as F1735 - 02(2008). DOI:
10.1520/F1735-09.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://www.dodssp.daps.mil.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
F1735 – 09
3
MIL-STD-129 Marking for Shipment and Storage
3. Terminology
3.1 General—Definitions are in accordance with Terminology D883 and Terminology F412. Abbreviations are in accordance
with Terminology D1600, unless otherwise indicated.
3.2
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.