Standard Practice for Agencies Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Testing Agency Evaluation

SIGNIFICANCE AND USE
4.1 The testing and inspection of concrete and concrete aggregates are important elements in obtaining quality construction. A testing agency providing these services shall be selected with care.  
4.2 A testing agency shall be deemed qualified to perform and report the results of its tests if the agency meets the requirements of this practice. The testing agency services shall be provided under the technical direction of a registered professional engineer.  
4.3 This practice establishes essential characteristics pertaining to the organization, personnel, facilities, and quality systems of the testing agency. This practice may be supplemented by more specific criteria and requirements for particular projects.
SCOPE
1.1 This practice identifies and defines the duties, responsibilities, and minimum technical requirements of testing agency personnel and the minimum technical requirements for equipment utilized in testing concrete and concrete aggregates for use in construction.  
1.2 This practice provides criteria for the evaluation of the capability of a testing agency to perform designated ASTM test methods on concrete and concrete aggregates. It can be used by an evaluation authority in the inspection or accreditation of a testing agency or by other parties to determine if the agency is qualified to conduct the specified tests.
Note 1: Specification E329 provides criteria for the evaluation of agencies that perform the inspection of concrete during placement.  
1.3 This practice provides criteria for Inspection Bodies and Accreditation Bodies that provide services for evaluation of testing agencies in accordance with this practice.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
14-Oct-2016
Current Stage
Ref Project

Relations

Buy Standard

Standard
ASTM C1077-16a - Standard Practice for Agencies Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Testing Agency Evaluation
English language
9 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
REDLINE ASTM C1077-16a - Standard Practice for Agencies Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Testing Agency Evaluation
English language
9 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: C1077 − 16a
Standard Practice for
Agencies Testing Concrete and Concrete Aggregates for
Use in Construction and Criteria for Testing Agency
1
Evaluation
This standard is issued under the fixed designation C1077; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope* C78/C78M Test Method for Flexural Strength of Concrete
(Using Simple Beam with Third-Point Loading)
1.1 This practice identifies and defines the duties,
C117 Test Method for Materials Finer than 75-µm (No. 200)
responsibilities, and minimum technical requirements of test-
Sieve in Mineral Aggregates by Washing
ing agency personnel and the minimum technical requirements
C125 Terminology Relating to Concrete and Concrete Ag-
for equipment utilized in testing concrete and concrete aggre-
gregates
gates for use in construction.
C127 Test Method for Relative Density (Specific Gravity)
1.2 This practice provides criteria for the evaluation of the
and Absorption of Coarse Aggregate
capabilityofatestingagencytoperformdesignatedASTMtest
C128 Test Method for Relative Density (Specific Gravity)
methodsonconcreteandconcreteaggregates.Itcanbeusedby
and Absorption of Fine Aggregate
an evaluation authority in the inspection or accreditation of a
C136/C136M Test Method for Sieve Analysis of Fine and
testing agency or by other parties to determine if the agency is
Coarse Aggregates
qualified to conduct the specified tests.
C138/C138M Test Method for Density (Unit Weight),Yield,
and Air Content (Gravimetric) of Concrete
NOTE 1—Specification E329 provides criteria for the evaluation of
agencies that perform the inspection of concrete during placement.
C143/C143M Test Method for Slump of Hydraulic-Cement
Concrete
1.3 This practice provides criteria for Inspection Bodies and
C172/C172M Practice for Sampling Freshly Mixed Con-
Accreditation Bodies that provide services for evaluation of
crete
testing agencies in accordance with this practice.
C173/C173M Test Method forAir Content of Freshly Mixed
1.4 This standard does not purport to address all of the
Concrete by the Volumetric Method
safety concerns, if any, associated with its use. It is the
C231/C231M Test Method forAir Content of Freshly Mixed
responsibility of the user of this standard to establish appro-
Concrete by the Pressure Method
priate safety and health practices and determine the applica-
C617/C617M Practice for Capping Cylindrical Concrete
bility of regulatory limitations prior to use.
Specimens
2. Referenced Documents C802 Practice for Conducting an Interlaboratory Test Pro-
2 gram to Determine the Precision of Test Methods for
2.1 ASTM Standards:
Construction Materials
C31/C31M Practice for Making and Curing Concrete Test
C1064/C1064M Test Method for Temperature of Freshly
Specimens in the Field
Mixed Hydraulic-Cement Concrete
C39/C39M Test Method for Compressive Strength of Cylin-
C1231/C1231M Practice for Use of Unbonded Caps in
drical Concrete Specimens
Determination of Compressive Strength of Hardened Cy-
lindrical Concrete Specimens
1
This practice is under the jurisdiction of ASTM Committee C09 on Concrete
D75/D75M Practice for Sampling Aggregates
andConcreteAggregatesandisthedirectresponsibilityofSubcommitteeC09.98on
D2419 Test Method for Sand Equivalent Value of Soils and
Evaluation of Laboratories.
Fine Aggregate
Current edition approved Oct. 15, 2016. Published October 2016. Originally
E4 Practices for Force Verification of Testing Machines
approved in 1987. Last previous edition approved in 2016 as C1077-16. DOI:
10.1520/C1077-16A.
E11 Specification for Woven Wire Test Sieve Cloth and Test
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Sieves
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
E329 Specification for Agencies Engaged in Construction
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. Inspection, Testing, or Special Inspection
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
C1077 − 16a
E1301 Guide for Proficiency Testing by Interlaboratory ation section of the Manual of Aggregate and Concrete
3 6
Comparisons (Withdrawn 2012) Testing. Thelistismerelyacollectionoforganizationswilling
to provide this service and is not an endorsement of any
2.2 ACI Standards:
ACI 214-77 Recommended Practice for
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C1077 − 16 C1077 − 16a
Standard Practice for
Agencies Testing Concrete and Concrete Aggregates for
Use in Construction and Criteria for Testing Agency
1
Evaluation
This standard is issued under the fixed designation C1077; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope*
1.1 This practice identifies and defines the duties, responsibilities, and minimum technical requirements of testing agency
personnel and the minimum technical requirements for equipment utilized in testing concrete and concrete aggregates for use in
construction.
1.2 This practice provides criteria for the evaluation of the capability of a testing agency to perform designated ASTM test
methods on concrete and concrete aggregates. It can be used by an evaluation authority in the inspection or accreditation of a
testing agency or by other parties to determine if the agency is qualified to conduct the specified tests.
NOTE 1—Specification E329 provides criteria for the evaluation of agencies that perform the inspection of concrete during placement.
1.3 This practice provides criteria for Inspection Bodies and Accreditation Bodies that provide services for evaluation of testing
agencies in accordance with this practice.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
C31/C31M Practice for Making and Curing Concrete Test Specimens in the Field
C39/C39M Test Method for Compressive Strength of Cylindrical Concrete Specimens
C78/C78M Test Method for Flexural Strength of Concrete (Using Simple Beam with Third-Point Loading)
C117 Test Method for Materials Finer than 75-μm (No. 200) Sieve in Mineral Aggregates by Washing
C125 Terminology Relating to Concrete and Concrete Aggregates
C127 Test Method for Relative Density (Specific Gravity) and Absorption of Coarse Aggregate
C128 Test Method for Relative Density (Specific Gravity) and Absorption of Fine Aggregate
C136C136/C136M Test Method for Sieve Analysis of Fine and Coarse Aggregates
C138/C138M Test Method for Density (Unit Weight), Yield, and Air Content (Gravimetric) of Concrete
C143/C143M Test Method for Slump of Hydraulic-Cement Concrete
C172/C172M Practice for Sampling Freshly Mixed Concrete
C173/C173M Test Method for Air Content of Freshly Mixed Concrete by the Volumetric Method
C231/C231M Test Method for Air Content of Freshly Mixed Concrete by the Pressure Method
C617/C617M Practice for Capping Cylindrical Concrete Specimens
C802 Practice for Conducting an Interlaboratory Test Program to Determine the Precision of Test Methods for Construction
Materials
C1064/C1064M Test Method for Temperature of Freshly Mixed Hydraulic-Cement Concrete
1
This practice is under the jurisdiction of ASTM Committee C09 on Concrete and Concrete Aggregates and is the direct responsibility of Subcommittee C09.98 on
Evaluation of Laboratories.
Current edition approved Feb. 1, 2016Oct. 15, 2016. Published April 2016October 2016. Originally approved in 1987. Last previous edition approved in 20152016 as
C1077–15a.-16. DOI: 10.1520/C1077-16. 10.1520/C1077-16A.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
C1077 − 16a
C1231/C1231M Practice for Use of Unbonded Caps in Determination of Compressive Strength of Hardened Cylindrical
Concrete Specimens
D75D75/D75M Practice for Sampling Aggregates
D2419 Test Method for Sand Equivalent Value of Soils and Fine Aggregate
E4 Practices for Force Verification of Testing Machines
E11 Specification for Woven Wire Test Sieve Cloth and Test Sieves
E329 Specification for Agencies Engaged in Const
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.