ASTM D2899-11
(Practice)Standard Practice for Establishing Allowable Stresses for Round Timber Piles
Standard Practice for Establishing Allowable Stresses for Round Timber Piles
SIGNIFICANCE AND USE
This practice is intended for use by associations, technical societies and other groups that develop national design standards and use recommendations for round timber piles.
In using allowable stresses established under this practice, factors specific to each end use which may affect the performance of the pile system shall be considered. Such factors include the location of the critical section, the bearing capacity of the soil, the ability of the pile to withstand driving forces and conditions of service.
SCOPE
1.1 This practice contains procedures for establishing allowable stresses for round timber piles starting with clear wood strength properties.
1.2 Stresses established under this practice are applicable to piles conforming to the quality, straightness, spiral grain, knot, check, shake, and split provisions of Specification D 25.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D2899–11
Standard Practice for
1
Establishing Allowable Stresses for Round Timber Piles
This standard is issued under the fixed designation D2899; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 3.1.3 load sharing—the distribution of load in proportion to
pile stiffness. This results in piles that perform as a group
1.1 Thispracticecontainsproceduresforestablishingallow-
reducing effects of between-pile variability and increasing
able stresses for round timber piles starting with clear wood
system reliability over that of piles which perform indepen-
strength properties.
dently.
1.2 Stresses established under this practice are applicable to
3.1.4 skin friction—the interaction between the pile surface
piles conforming to the quality, straightness, spiral grain, knot,
and the soil which serves to distribute load either away from or
check, shake, and split provisions of Specification D25.
into a pile. A positive skin friction refers to pile loads
1.3 This standard does not purport to address all of the
distributed to the soil. Negative skin friction distributes load to
safety concerns, if any, associated with its use. It is the
the pile when soil strata subside or consolidate.
responsibility of the user of this standard to establish appro-
3.2 Symbols:
priate safety and health practices and determine the applica-
C = adjustment for small clear compression perp for an-
cp
bility of regulatory limitations prior to use.
nual ring orientation (1/1.67)
2. Referenced Documents C = conditioning factor
ct
2
C = adjustment for duration of load and factor of safety
2.1 ASTM Standards: dol
C = adjustment for density applied for Douglas fir and
d
D25 Specification for Round Timber Piles
Southern pine only
D245 Practice for Establishing Structural Grades and Re-
C = combined adjustment for form and size (= 0.97)
fs
lated Allowable Properties for Visually Graded Lumber
C = adjustment for grade characteristics applied to all
D2555 Practice for Establishing Clear Wood Strength Val- g
species including bending (0.75), compression (0.93), and
ues
shear (0.50)
3. Terminology
C = adjustment for height in the tree (= 0.96 if softwoods
h
and = 1.0 for hardwoods)
3.1 Definitions:
C = adjustment for height and for reduced variability
3.1.1 allowable stress—the numeric value of pile strength hv
(MOR = 0.91forsoftwoods,1.05forhardwoods, C// = 0.91for
that is appropriate for use in structural analysis.
softwoods, 1.05 for hardwoods, Shear = 0.99 for softwoods,
3.1.2 end-bearing—compression-parallel-to-the-grain
1.03 for hardwoods)
stress resulting when pile load is not carried to the soil through
C = load sharing adjustment (structural engineers option)
skin friction. ls
C = size adjustment
s
C = adjustment for shear deflection in calculation for bend-
v
1
This practice is under the jurisdiction of ASTM Committee D07 on Wood and
ing modulus of elasticity (= 1.06)
is the direct responsibility of Subcommittee D07.04 on Pole and Pile Products.
D = diameter of a round timber pile
Current edition approved Nov. 15, 2011. Published December 2011. Originally
E = clear wood unseasoned average modulus of elasticity
approved in 1970 as D2899 – 70 T. Last previous edition approved in 2003 as
D2899 – 03. DOI: 10.1520/D2899-11.
from Test Methods D2555
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
MOE = modulus of elasticity (average)
contactASTM Customer Service at service@astm.org. ForAnnual Book of ASTM
F = allowable stress for stress designated by the subscript b
Standards volume information, refer to the standard’s Document Summary page on b
the ASTM website. F = allowable compression stress for pile tips
c
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
D2899–11
f = small clear lower 5 % exclusion compression strength 7. Pile Variability
c05
in accordance with Test Methods D2555
7.1 Standard deviations given in Test Methods D2555 and
f = lower 5 % exclusion value for stress “x” determined
used to calculate 5 % exclusion values include both variability
i05
using the green, small clear strength and standard deviation
in properties between trees and variability in properties occur-
values reported in Test Methods D2555
ring within the cross section and along the length of an
b = stress value subscripts, c = compression parallel,
individual tree.
cp = compression perpendicular, b = bending, v = shear
7.2 For round timber piles, only the between tree compo-
nent of varian
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:D2899–03 Designation:D2899–11
Standard Practice for
1
Establishing Allowable Stresses for Round Timber Piles
This standard is issued under the fixed designation D2899; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 Thispracticecontainsproceduresforestablishingallowablestressesforroundtimberpilesstartingwithclearwoodstrength
properties.
1.2 Stresses established under this practice are applicable to piles conforming to the quality, straightness, spiral grain, knot,
check, shake, and split provisions of Specification D25.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D25 Specification for Round Timber Piles
D245 Practice for Establishing Structural Grades and Related Allowable Properties for Visually Graded Lumber
D2555 Practice for Establishing Clear Wood Strength Values
3. Terminology
3.1 Definitions:
3.1.1 allowable stress—the numeric value of pile strength that is appropriate for use in structural analysis.
3.1.2 end-bearing—compression-parallel-to-the-grain stress resulting when pile load is not carried to the soil through skin
friction.
3.1.3 load sharing—the distribution of load in proportion to pile stiffness. This results in piles that perform as a group reducing
effects of between-pile variability and increasing system reliability over that of piles which perform independently.
3.1.4 skin friction—the interaction between the pile surface and the soil which serves to distribute load either away from or into
a pile. A positive skin friction refers to pile loads distributed to the soil. Negative skin friction distributes load to the pile when
soil strata subside or consolidate.
3.2 Symbols:
C = adjustment for small clear compression perp for annual ring orientation (1/1.67)
cp
C = conditioning factor
ct
C = adjustment for duration of load and factor of safety
dol
C = adjustment for density applied for Douglas fir and Southern pine only
d
C = combined adjustment for form and size (= 0.97)
fs
C = adjustment for grade characteristics applied to all species including bending (0.75), compression (0.93), and shear (0.50)
g
C = adjustment for height in the tree (= 0.96 if softwoods and = 1.0 for hardwoods)
h
C = adjustment for height and for reduced variability (MOR = 0.91 for softwoods, 1.05 for hardwoods, C// = 0.91 for
hv
softwoods, 1.05 for hardwoods, Shear = 0.99 for softwoods, 1.03 for hardwoods)
C = load sharing adjustment (structural engineers option)
ls
C = size adjustment
s
C = adjustment for shear deflection in calculation for bending modulus of elasticity (= 1.06)
v
D = diameter of a round timber pile
E = clear wood unseasoned average modulus of elasticity from Test Methods D2555
1
This practice is under the jurisdiction of ASTM Committee D07 on Wood and is the direct responsibility of Subcommittee D07.04 on Pole and Pile Products.
Current edition approved Oct. 1, 2003.Nov. 15, 2011. Published December 2003.2011. Originally approved in 1970 as D2899 – 70 T. Last previous edition approved in
20012003 as D2899 – 013. DOI: 10.1520/D2899-03.10.1520/D2899-11.
2
ForreferencedASTMstandards,visittheASTMwebsite,www.astm.org,orcontactASTMCustomerServiceatservice@astm.org.ForAnnualBookofASTMStandards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
D2899–11
MOE = modulus of elasticity (average)
F = allowable stress for stress designated by the subscript b
b
F = allowable compression stress for pile tips
c
f = small clear lower 5 % exclusion compression strength in accordance with Test Methods D2555
c05
f = lower 5 % exclusion value for stress “x” determined using the green, small clear strength and standard deviation values
i05
reported in Test Methods D2555
b = stress value subscripts, c = compression parallel, cp = compression perpendicular, b = bending, v = shear
4. Significance and Use
4.1 This practice is intende
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.