iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM E2515-09

(Test Method)

Standard Test Method for Determination of Particulate Matter Emissions Collected by a Dilution tunnel

Standard Test Method for Determination of Particulate Matter Emissions Collected by a Dilution tunnel

SCOPE
1.1 This test method is applicable for the determination of particulate matter emissions from solid-fuel-burning appliances including woodstoves, pellet-burning appliances, factory-built fireplaces, masonry fireplaces, masonry heaters, indoor furnaces, and indoor and outdoor hydronic heaters within a laboratory environment.
1.2 Analytes will be a particulate matter (PM) with no CAS number assigned. For data quality objectives, see Appendix X1.
1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard.
1.4 This test method does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
30-Apr-2009
ICS
13.040.40 - Stationary source emissions
Technical Committee
E06 - Performance of Buildings
Drafting Committee
E06.54 - Solid Fuel Burning Appliances
Current Stage
Ref Project

Relations

Replaces
ASTM E2515-07 - Standard Test Method for Determination of Particulate Matter Emissions Collected by a Dilution tunnel
Effective Date
01-May-2009
Replaced By
ASTM E2515-10 - Standard Test Method for Determination of Particulate Matter Emissions Collected by a Dilution tunnel
Effective Date
01-Sep-2010
Referred By
ASTM E2780-10(2017) - Standard Test Method for Determining Particulate Matter Emissions from Wood Heaters
Effective Date
01-May-2009
Referred By
ASTM E2618-13(2019) - Standard Test Method for Measurement of Particulate Emissions and Heating Efficiency of Solid Fuel-Fired Hydronic Heating Appliances
Effective Date
01-May-2009
Referred By
ASTM E3053-18e2 - Standard Test Method for Determining Particulate Matter Emissions from Wood Heaters Using Cordwood Test Fuel
Effective Date
01-May-2009
Referred By
ASTM E2817-11(2018) - Standard Test Method for Test Fueling Masonry Heaters
Effective Date
01-May-2009
Referred By
ASTM E2558-13(2021) - Standard Test Method for Determining Particulate Matter Emissions from Fires in Wood-Burning Fireplaces
Effective Date
01-May-2009
Referred By
ASTM E2779-10(2017) - Standard Test Method for Determining Particulate Matter Emissions from Pellet Heaters
Effective Date
01-May-2009

Buy Standard

ASTM E2515-09 - Standard Test Method for Determination of Particulate Matter Emissions Collected by a Dilution tunnelASTM E2515-09 - Standard Test Method for Determination of Particulate Matter Emissions Collected by a Dilution tunnel
PreviousNext
Standard
ASTM E2515-09 - Standard Test Method for Determination of Particulate Matter Emissions Collected by a Dilution tunnel
English language
15 pages
sale 15% off
Preview
sale 15% off
Preview
REDLINE ASTM E2515-09 - Standard Test Method for Determination of Particulate Matter Emissions Collected by a Dilution tunnelREDLINE ASTM E2515-09 - Standard Test Method for Determination of Particulate Matter Emissions Collected by a Dilution tunnel
PreviousNext
Standard
REDLINE ASTM E2515-09 - Standard Test Method for Determination of Particulate Matter Emissions Collected by a Dilution tunnel
English language
15 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:E2515–09
Standard Test Method for
Determination of Particulate Matter Emissions Collected by
1
a Dilution Tunnel
This standard is issued under the fixed designation E2515; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
4
1. Scope 2.2 AISI Documents:
AISI 316 Stainless Steel
1.1 This test method is applicable for the determination of
particulate matter emissions from solid-fuel-burning appli-
3. Terminology
ances including woodstoves, pellet-burning appliances,
3.1 Definitions of Terms Specific to This Standard:
factory-built fireplaces, masonry fireplaces, masonry heaters,
3.1.1 laboratory environment—the area or room that is used
indoor furnaces, and indoor and outdoor hydronic heaters
for the storage, weighing, assembly, disassembly, and desicca-
within a laboratory environment.
tion of filters and related equipment (sample recovery and
1.2 Analytes will be a particulate matter (PM) with no CAS
analysis).
number assigned. For data quality objectives, see Appendix
3.1.2 particulate matter (PM)—all gas-borne matter result-
X1.
ing from combustion of solid fuel, as specified in the appliance
1.3 The values stated in SI units are to be regarded as
operation test method, that is collected and retained by the
standard. The values given in parentheses are mathematical
specified filter and probe system under the conditions of the
conversions to inch-pound units that are provided for informa-
test.
tion only and are not considered standard.
3.1.3 test facility—the area in which the tested appliance is
1.4 This test method does not purport to address all of the
installed, operated, and sampled for emissions.
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appro-
4. Summary of Test Method
priate safety and health practices and determine the applica-
4.1 The total flue-gas exhaust from a solid fuel burning
bility of regulatory limitations prior to use.
appliance is collected along with ambient dilution air with a
collection hood. Duplicate sampling trains are used to extract
2. Referenced Documents
2 gas samples from the dilution tunnel for determination of
2.1 ASTM Standards:
particulate matter concentrations. Each sample train has two
D2986 Practice for Evaluation of Air Assay Media by the
3 glass fiber filters in series. The samples are withdrawn at a
Monodisperse DOP (Dioctyl Phthalate) Smoke Test
consistently proportional rate from sampling points located at
E2558 Test Method for Determining Particulate Matter
the centroid of a sampling tunnel. During sampling, the filters
Emissions from Fires in Low Mass Wood-Burning Fire-
are maintained at a temperature less than 32°C (90°F). The
places
mass of the sampled particulate matter is determined gravi-
E2618 Test Method for Measurement of Particulate Emis-
metrically after the removal of uncombined water. The total
sions and Heating Efficiency of Outdoor Solid Fuel-Fired
particulate matter mass collected on the filters and in the probe
Hydronic Heating Appliances
and front filter housing are multiplied by the ratio of the
dilution tunnel flow to sample flow to determine the total
1
This test method is under the jurisdiction of ASTM Committee E06 on
particulate emissions during a test.
Performance of Buildings and is the direct responsibility of Subcommittee E06.54
4.2 The sampling system for this test method consists of
on Solid Fuel Burning Appliances.
duplicatedual-filterdrysamplingtrains.Bothoftheparticulate
Current edition approved May 1, 2009. Published June 2009. Originally
approved in 2007. Last previous edition approved in 2007 as E2515 – 07. DOI:
sampling trains are operated simultaneously at a sample flow
3
10.1520/E2515-09.
rate not to exceed 0.007 m /min (0.25 cfm/min). The total
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
particulate results obtained from the two sampling trains are
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
3 4
Withdrawn. The last approved version of this historical standard is referenced Available from American Iron and Steel Institute (AISI), 1140 Connecticut
on www.astm.org. Ave., NW, Suite 705, Washington, DC 20036, http://www.steel.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
E2515–09
averaged to determine the particulate emissions and are com- 6.1.1.1 Filter Holder Ass
...

This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:E2515–07 Designation:E2515–09
Standard Test Method for
Determination of Particulate Matter Emissions Collected by
1
a Dilution Tunnel
This standard is issued under the fixed designation E 2515; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This test method is applicable for the determination of particulate matter emissions from solid-fuel-burning appliances
including woodstoves, pellet-burning appliances, factory-built fireplaces, masonry fireplaces, masonry heaters, indoor furnaces,
and indoor and outdoor hydronic heaters within a laboratory environment.
1.2 Analytes will be a particulate matter (PM) with no CAS number assigned. For data quality objectives, see Appendix X1.
1.3The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions
to inch-pound units that are provided for information only and are not considered standard.
1.4 This test method does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D 2986 Practice for Evaluation of Air Assay Media by the Monodisperse DOP (Dioctyl Phthalate) Smoke Test
E 2558 Test Method for Determining Particulate Matter Emissions from Fires in Low Mass Wood-Burning Fireplaces Test
Method for Determining Particulate Matter Emissions from Fires in Low Mass Wood-Burning Fireplaces
E 2618 Test Method for Measurement of Particulate Emissions and Heating Efficiency of Outdoor Solid Fuel-Fired Hydronic
Heating Appliances
1
This test method is under the jurisdiction ofASTM Committee E06 on Performance of Buildings and is the direct responsibility of Subcommittee E06.54 on Solid Fuel
Burning Appliances.
Current edition approved May 1, 2007. Published May 2007.
Current edition approved May 1, 2009. Published June 2009. Originally approved in 2007. Last previous edition approved in 2007 as E 2515 – 07.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
E2515–09
3
2.2 AISI Documents:
AISI 316 Stainless Steel
3. Terminology
3.1Definitions: General
3.1 Definitions of Terms Specific to This Standard:
3.1.1 laboratory environment—the area or room that is used for the storage, weighing, assembly, disassembly, and desiccation
of filters and related equipment (sample recovery and analysis).
3.1.2 particulate matter (PM)—all gas-borne matter resulting from combustion of solid fuel, as specified in the appliance
operation test method, that is collected and retained by the specified filter and probe system under the conditions of the test.
3.1.3 test facility—the area in which the tested appliance is installed, operated, and sampled for emissions.
4. Summary of Test Method
4.1 The total flue-gas exhaust from a solid fuel burning appliance is collected along with ambient dilution air with a collection
hood. Duplicate sampling trains are used to extract gas samples from the dilution tunnel for determination of particulate matter
concentrations. Each sample train has two glass fiber filters in series.The samples are withdrawn at a consistently proportional rate
from sampling points located at the centroid of a sampling tunnel. During sampling, the filters are maintained at a temperature less
than32°C(90°F).Themassofthesampledparticulatematterisdeterminedgravimetricallyaftertheremovalofuncombinedwater.
The total particulate matter mass collected on the filters and in the probe and front filter housing are multiplied by the ratio of the
dilution tunnel flow to sample flow to determine the total particulate emissions during a test.
4.2 The sampling system for this test method consists of duplicate dual-fi
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM E2558-13(2021)(Test Method)
Standard Test Method for Determining Particulate Matter Emissions from Fires in Wood-Burning Fireplaces

SIGNIFICANCE AND USE
5.1 This test method is used for determining emission factors and emission rates for low mass wood-burning fireplaces.  
5.1.1 The emission factor is useful for determining emission performance during product development.  
5.1.2 The emission factor is useful for the air quality regulatory community for determining compliance with emission performance limits.  
5.1.3 The emission rate may be useful for the air quality regulatory community for determining impacts on air quality from fireplaces, but must be used with caution as use patterns must be factored into any prediction of atmospheric particulate matter impacts from fireplaces based on results from this method.  
5.2 The reporting units are grams of particulate per kilogram of dry fuel and grams of particulate per hour.  
5.2.1 Appropriate reporting units for comparing emissions from non-heating appliances: grams per kilogram.  
5.2.2 Appropriate reporting units for predicting atmospheric emission impacts only if hours of fireplace use are factored in: grams per hour.
SCOPE
1.1 This test method covers the fueling and operating protocol for determining particulate matter emissions from wood fires in low mass wood-burning fireplaces. The fueling and operating protocol for determining particular matter emissions from masonry or other high mass fireplaces is covered in Annex A1 of this test method.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    18 pages
    English language
    sale 15% off
ASTM
ASTM E2515-11(2017)(Test Method)
Standard Test Method for Determination of Particulate Matter Emissions Collected by a Dilution Tunnel

SCOPE
1.1 This test method is applicable for the determination of particulate matter emissions from solid-fuel-burning appliances including woodstoves, pellet-burning appliances, factory-built fireplaces, masonry fireplaces, masonry heaters, indoor furnaces, and indoor and outdoor hydronic heaters within a laboratory environment.  
1.2 Analytes will be a particulate matter (PM) with no CAS number assigned. For data quality objectives, see Appendix X1.  
1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard.  
1.4 This test method does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    15 pages
    English language
    sale 15% off
ASTM
ASTM D5438-23(Practice)
Standard Practice for Collection of Floor Dust for Chemical Analysis

SIGNIFICANCE AND USE
5.1 This practice may be used to collect dust from carpeted or bare floor surfaces for gravimetric or chemical analysis. The collected sample is substantially unmodified by the sampling procedure.  
5.2 This practice provides for a reproducible dust removal rate from level loop and plush carpets, as well as bare floors. It has the ability to achieve relatively constant removal efficiency at different loadings of floor dust.  
5.3 This practice also provides for the efficient capture of semivolatile organic chemicals associated with the dust. The test system can be fitted with special canisters downstream of the cyclone for the capture of specific semivolatile organic chemicals that may volatilize from the dust particles during collection.  
5.4 This practice does not describe procedures for evaluation of the safety of floor surfaces or the potential human exposure to floor dust. It is the user's responsibility to evaluate the data collected by this practice and make such determinations in the light of other available information.  
5.5 This practice provides per-event dust chemical concentration and chemical loading. Advantages and trade-offs of different sampling approaches have been discussed (7).  
5.6 This practice uses a removable, cleanable dropout jar that facilitates per-event sampling. Other per-event vacuum attachments are commercially available. These are not directly comparable with composite sampling done using whole vacuum cleaner bags.
SCOPE
1.1 This practice covers a procedure for the collection of a sample of dust from carpets and bare floors that can be analyzed for inorganic metals such as lead and organic compounds such as pesticides and other semi-volatile organic compounds (SVOCs).  
1.2 This practice is applicable to a variety of carpeted and bare floor surfaces. It has been tested for level loop and plush pile carpets and bare wood floors, specifically. This practice is not applicable to elevated, non-floor surfaces.  
1.3 This practice is not intended for the collection and evaluation of dust for the presence of asbestos fibers.  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 This practice describes use of a sampling device, the High-Volume Small Surface Sampler (HVS3). Other event-based sampling devices that use commercially available vacuum attachments are not in scope. Composite sampling using whole vacuum cleaner bags is not in scope. Other approaches for floor or non-floor surface sampling (Practices D6966, D6661, D7144) are not within the scope.  
1.6 This practice only applies to the HVS3. Other dust sampling methods may or may not be directly comparable. Method evaluation for other dust sampling approaches is encouraged. This could be done by comparison with methods outlined in this standard practice for HVS3 or through independent evaluation using field spikes and certified reference materials.  
1.7 This practice provides information on dust loading, chemical dust concentration, and chemical dust loading. Information on the type of floor, the floor surface area sampled, and amount of dust collected is required (see Fig. 2). Cleaning the vacuum attachments in between sampling events is also required (see Section 13).  
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    9 pages
    English language
    sale 15% off
  • Standard
    9 pages
    English language
    sale 15% off
ASTM
ASTM E1605-22(Terminology)
Standard Terminology Relating to Lead in Buildings

SIGNIFICANCE AND USE
3.1 The purpose of this terminology standard is to help users understand and apply the large number of specialized terms used in connection with the management of lead hazards by providing a single, comprehensive, and consistent terminology.  
3.1.1 This terminology standard includes some terms that may be encountered, but whose use is discouraged. They are included for clarification and in order to provide the user with preferred existing alternate terms.  
3.1.2 Architectural terms for individual building components are included to promote consistency of usage and to help ensure that sampling locations are recorded with sufficient accuracy to allow independent confirmation of lead measurements, if necessary.  
3.2 A discussion is attached to certain definitions to help make the definition clear or to show how the term and its definition are related to other terms.  
3.3 Terms and definitions in this terminology standard are based upon laws, regulations, and practices in the United States of America.  
3.3.1 Some of the definitions in this terminology standard are adopted verbatim or are adapted from definitions that are formally stated or implied in laws and regulations. They are not intended to replace the latter definitions. The user is responsible for understanding legal definitions and for ensuring that the legal obligations that are encompassed by them are fully satisfied.  
3.3.2 Users in other countries should refer to applicable national, regional, and local laws, regulations, and practices.
SCOPE
1.1 This terminology standard covers definitions for the following:  
1.1.1 Terms that are commonly used in the field of management of lead hazards in facilities;  
1.1.2 Architectural terms, particularly those associated with older wood-frame buildings; and,  
1.1.3 Specialized terms that may be encountered by users in reports and notices that are generated during lead hazard management activities.  
1.2 This terminology standard is supplementary to Terminology E631.  
1.3 Definitions adopted or derived from other documents include the following:  
1.3.1 Some of the definitions in this terminology standard are adopted as exact copies from other sources. The source is briefly identified at the right margin following the definition and fully identified in Section 2.  
1.3.2 Some of the definitions in this terminology standard are adapted from other sources. Changes in these definitions were made only to clarify the meaning, to incorporate related terms that also are defined in this terminology standard, or to ensure that the revised definition is consistent with those for related terms. The source is briefly identified with the words “adapted” at the right margin following the definition, and is fully identified in Section 2.  
1.4 Terms within the definitions that are shown in boldface are defined in this terminology standard.  
1.5 This terminology standard excludes the following:  
1.5.1 Terms with a common dictionary meaning, except in cases where there is a specialized definition within the field of lead hazard management.  
1.5.2 Terms that are used only in individual ASTM standards in which they are defined adequately, whether formally or by the context in which they appear.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    10 pages
    English language
    sale 15% off
  • Standard
    10 pages
    English language
    sale 15% off
ASTM
ASTM D6830-02(2022)(Test Method)
Standard Test Method for Characterizing the Pressure Drop and Filtration Performance of Cleanable Filter Media

SIGNIFICANCE AND USE
5.1 This test method determines the comparative performance of filter media. The results can be used for design, manufacturing, construction and selection of filter media.  
5.2 Results obtained by this test method should not be used to predict absolute performance on full scale fabric filter (baghouse) facilities, however these results will be useful in selection of proper filter media and identification of recommended operating parameters for these full scale fabric filter facilities.  
5.3 Dust types vary greatly; therefore, the results obtained using the standard dust should not be extrapolated to other dust types.
SCOPE
1.1 This test method characterizes the operational performance of cleanable filter media under specified laboratory conditions.  
1.2 This test method determines the airflow resistance, drag, cleaning requirements, and particulate filtration performance of pulse cleaned filter media.  
1.3 This test method determines the comparative performance of cleanable filter media.  
1.4 The results obtained from this test method are useful in the design, construction, and selection of filter media.  
1.5 The results obtained by this test method should not be used to predict absolute performance of full scale fabric filter (baghouse) facilities, however these results will be useful in selection of proper filter media and identification of recommended operating parameters for these full scale fabric filter facilities.  
1.6 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    9 pages
    English language
    sale 15% off
ASTM
ASTM D7938-21(Practice)
Standard Practice for Sampling of C-14 in Gaseous Effluents

SIGNIFICANCE AND USE
5.1 This practice was developed4 for the purpose of sampling gaseous effluent streams from a facility that releases 14C in either organic or inorganic forms.  
5.1.1 For many years 14C was not included in gaseous and liquid effluent measurements used for effluent dose calculations at nuclear power facilities. U.S. NRC Regulatory Guide 1.21 now requires 14C analysis (either estimated by calculation or actual measurement) and its impact on annual dose in the environs of nuclear plants be evaluated. Based on the revisions to the Regulatory Guide and NRC guidance to licensees, 14C activity will need to be reported and evaluated for dose contribution based on the activity concentration and chemical form of the 14C in the release.  
5.2 While 14C releases may be estimated, the measurement of actual 14C emissions provides a more reliable and accurate means of reporting emissions. The chemical form of 14C that yields the greatest dose significance due to uptake by living organisms is the inorganic form. Thus the distribution of 14C chemical forms in plant effluents is important in assessing the overall dose impact.  
5.3 Use of this sampling practice has identified that for pressurized water reactors (PWRs) >90 % of all 14C released may be in the organic form during operation, and for boiling water reactors (BWRs) 14C released may be in the organic form during operation.  
5.3.1 Some power plants have catalytic hydrogen recombiners in the waste gas processing system. These can also oxidize organic carbon to CO2, increasing the percentage of 14CO2 in the effluent release.  
5.3.2 During refueling outages, oxidizing conditions exist in the reactor cavity due to air saturation and radiolytic reactions by the nuclear fuel. The combination of these two effects has been shown to increase the 14CO2 content of the sampled atmosphere inside the containment building.  
5.4 The sampling methodology described in this practice is not capable of discriminating between different org...
SCOPE
1.1 The intended use of this practice is for sampling of gasses containing 14C in inorganic, organic or particulate forms. This sampling practice captures the 14C in a media that can be submitted to a laboratory for analysis, typically by liquid scintillation counting (LSC)  
1.2 This practice does not include the needed steps for the liberation of 14C from the media on which it was adsorbed or those for the preparation for LSC sample preparation in the laboratory prior to liquid scintillation analysis. This practice does not include the methodology used to analyze the prepared samples by LSC.  
1.3 The overall 14C analytical detection capability is impacted by a number of factors including the volume sampled, the method used to desorb the 14C from the media, and the analytical method used the measure 14C from the media. This practice only directly addresses the volume of the gas stream from which any present 14C would be adsorbed.  
1.4 The values stated in pCi units are to be regarded as standard given the reporting requirements of the U.S. NRC Regulatory Guide 1.21. The Bq values given in parenthesis are mathematical conversions to SI units that are provided for information only and are not considered standard. Other values stated in SI units are to be regarded as standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM E1583-21a(Practice)
Standard Practice for Evaluating Laboratories Engaged in Determination of Lead in Paint, Dust, Airborne Particulates, and Soil Taken From and Around Buildings and Related Structures

SIGNIFICANCE AND USE
4.1 This practice provides the basic criteria to be used by accreditation bodies and others in evaluating the qualifications of laboratories engaged in the testing of lead in paint, or settled dust, or airborne particulates, or soil, or combination thereof, taken from and around buildings and related structures. The criteria in this practice shall be supplemented by additional specific criteria and requirements, when appropriate; for example, when necessary to be in accordance with federal, state, or local government regulations.  
4.2 The accreditation is for organizations and not individuals.  
4.3 The practice is intended to provide objective information on the capabilities needed by laboratories to determine lead in paint, dust, airborne particulates, and soil taken from and around buildings and related structures. It is not intended to be used to compare one laboratory with another.  
4.4 This practice is also intended for use by laboratories in the development and implementation of their management systems and for use to request or perform an evaluation of in-house facilities in accordance with this practice.
SCOPE
1.1 This practice covers the qualifications, including minimum requirements for personnel and equipment, duties, responsibilities, and services of laboratories engaged in the determination of lead in paint, or settled dust, or airborne particulates, or soil, or any combination thereof, taken from and around buildings and related structures.  
1.2 This practice has been developed consistent with Guides E548 and E994, to supplement ISO/IEC 17025.  
1.3 This practice contains notes that are explanatory and are not part of the mandatory requirements of the practice.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D3685/D3685M-13(2021)(Test Method)
Standard Test Methods for Sampling and Determination of Particulate Matter in Stack Gases

SIGNIFICANCE AND USE
5.1 The measurement of particulate matter and collected residue emission rates is an important test widely used in the practice of air pollution control. Particulate matter measurements after control devices are necessary to determine total emission rates to the atmosphere.  
5.1.1 These measurements, when approved by federal and state agencies, are often required for the purpose of determining compliance with regulations and statutes.  
5.1.2 The measurements made before and after control devices are often necessary as a means of demonstrating conformance with contractual performance specifications.  
5.2 The collected residue obtained with these test methods is also important in characterizing stack emissions. However, the utility of these data is limited unless a chemical analysis of the collected residue is performed.
SCOPE
1.1 These test methods describe procedures to determine the mass emission rates of particulate matter and collected residue in gaseous streams by in-stack test methods (Test Method A) or out-of-stack test methods (Test Method B).  
1.2 These test methods are suitable for measuring particulate matter and collected residue concentrations.  
1.3 These test methods include a description of equipment and procedures to be used for obtaining samples from effluent ducts and stacks, a description of equipment and procedures for laboratory analysis, and a description of procedures for calculating results.  
1.4 These test methods are applicable for sampling particulate matter and collected residue in wet (Test Method A or B) or dry (Test Method A) streams before and after particulate matter control equipment, and for determination of control device particulate matter collection efficiency.  
1.5 These test methods are also applicable for determining compliance with regulations and statutes limiting particulate matter existing in stack gases when approved by federal or state agencies.  
1.6 The particulate matter and collected residue samples collected by these test methods may be used for subsequent size and chemical analysis.  
1.7 These test methods describe the instrumentation, equipment, and operational procedures, including site selection, necessary for sampling and determination of particulate mass emissions. These test methods also include procedures for collection and gravimetric determination of residues collected in an impinger-condenser train. The sampling and analysis of particulate matter may be performed independently or simultaneously with the determination of collected residue.  
1.8 These test methods provide for the use of optional filter designs and filter material as necessary to accommodate the wide range of particulate matter loadings to which the test methods are applicable.  
1.9 Stack temperatures limitation for Test Method A is approximately 400°C (752°F) and for Test Method B is 815°C (1500°F).  
1.10 A known limitation of these test methods concerns the use of collected residue data. Since some collected residues can be formed in the sample train by chemical reaction in addition to condensation, these data should not be used without prior characterization (see 4.4.1).  
1.10.1 A second limitation concerns the use of the test methods for sampling gas streams containing fluoride, or ammonia or calcium compounds in the presence of sulfur dioxide and other reactive species having the potential to react within the sample train.  
1.10.2 A suspected but unverified limitation of these test methods concerns the possible vaporization and loss of collected particulate organic matter during a sampling run.  
1.11 The values stated in either SI units or inch-pound units are to be regarded separately as standard within the text. The inch-pound units are shown in parentheses. The values stated in each system are not exact equivalents; therefore each system shall be used independently of the other. Combining values from the two systems may result in ...

  • Standard
    18 pages
    English language
    sale 15% off
ASTM
ASTM D5485-21(Test Method)
Standard Test Method for Determining Corrosive Effect of Combustion Products Using the Cone Corrosimeter

SIGNIFICANCE AND USE
5.1 The metal loss from corrosion is directly related to the increase in electrical resistance of the target due to the decrease in conductive cross-sectional area.  
5.2 The relationship between resistance increase of metallic targets used in this test method and the amount of metal loss as reported by a uniform loss in thickness has not been determined.  
5.3 This test method is used to determine the corrosive effect of combustion products from burning electrical insulations or coverings or their constituent materials or components. Corrosion is determined by the reduction of thickness of the metal on standardized targets, as measured by electrical resistance. These targets are not necessarily representative of the intended end use.  
5.4 This test method is intended for use in electrical insulations or coverings material and product evaluations, for additional data to assist in design of electrical insulations or coverings products, or for development and research of electrical insulations or coverings products.  
5.5 A value of the initial test heat flux is selected to be relevant to the fire scenario being investigated (up to 100 kW/m2). Additional information for testing is given in A1.2.3.
SCOPE
1.1 This fire-test-response standard measures the corrosive effect by loss of metal from the combustion products of materials, components, or products.  
1.2 This test method provides corrosion results of product and material specimens limited to a maximum size of 100 by 100 mm in area and 50 mm thick.  
1.3 Additional information regarding the targets, the test conditions, and test limitations is provided in Annex A1.  
1.4 The results of this test method have not been investigated with respect to correlation to actual fires.  
1.5 An ISO standard exists, as developed by ISO TC 61 (Plastics), subcommittee 4 (on burning behavior), which is technically very similar to this test method and is designated ISO 11907-4.  
1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. (See IEEE/ASTM SI10.)  
1.7 This standard measures and describes the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions.  
1.8 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests.  
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 7.  
1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    14 pages
    English language
    sale 15% off
  • Standard
    14 pages
    English language
    sale 15% off
ASTM
ASTM F2326-04(2021)(Test Method)
Standard Test Method for Collection and Analysis of Visible Emissions from Candles as They Burn

SIGNIFICANCE AND USE
5.1 The intent of this test method is to aid the candle manufacturer to optimize candle formulations in the reduction of visible smoke emissions.  
5.2 This test method is intended to provide candle manufacturers a standard procedure to use during development of candle designs and formulations to compare relative smoke/burn behavior. For the development of this method, a protocol was established for trimming the wick on specially prepared test candles to 6 mm to 7 mm (1/4 in.) prior to each burn cycle. It is recommended that the manufacturer determine a standardized protocol, that is, either not trimming the wick or trimming the wick to an appropriate length in order for direct comparison of results.  
5.3 A relative ranking of candle formulations can be established with the use of a histogram of the data and control charts.  
5.4 This test method is not intended to set forth pass/fail criteria for visible smoke emissions from candles, as such, this method sets no standard level for visible smoke emissions.
SCOPE
1.1 This test method covers the collection and analysis of visible emissions from indoor use candles as they burn.  
1.2 The test is to be used to compare relative smoke/burn behavior during development of candle designs and formulations.  
1.3 This test method may not be suitable for multiple wick candles; tapers and candles intended to be burned while floating on water commonly known as “floaters.”  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off