ASTM C1116/C1116M-10

Standard Specification for Fiber-Reinforced Concrete

ABSTRACT
This specification covers all forms of fiber-reinforced concrete that are delivered to a purchaser with the ingredients uniformly mixed. This specification may also apply to fiber-reinforced concrete intended for shotcreting by the dry-mix process when sampling and testing is possible at the point of placement. It, however, does not cover the placement, consolidation, curing, or protection of the fiber-reinforced concrete after delivery to the purchaser. Materials are classified according to the type of fiber incorporated, which are: Type I, steel fiber-reinforced concrete that contains stainless, alloy, or carbon steel fibers; Type II, glass fiber-reinforced concrete that contains alkali-resistant glass fibers; Type III, synthetic fiber-reinforced concrete that contains synthetic fibers; and Type IV, natural fiber-reinforced concrete that contains cellulose fibers. The fiber-reinforced concretes shall be furnish either by batch mixing or continuous mixing, and shall be free of fiber balls when delivered to the point designated by the purchaser. Tolerances, acceptance criteria, and performance requirements for workability and air content are discussed thoroughly.
SCOPE
1.1 This specification covers all forms of fiber-reinforced concrete that are delivered to a purchaser with the ingredients uniformly mixed, and that can be sampled and tested at the point of delivery. It does not cover the placement, consolidation, curing, or protection of the fiber-reinforced concrete after delivery to the purchaser.
1.2 Certain sections of this specification are also applicable to fiber-reinforced concrete intended for shotcreting by the dry-mix process when sampling and testing of concrete is possible only at the point of placement. In this case, the sections dealing with batching plant, mixing equipment, mixing and delivery, and measurement of workability and air content, are not applicable.
1.3 This specification does not cover thin-section glass fiber-reinforced concrete manufactured by the spray-up process that is under the jurisdiction of ASTM Subcommittee C27.40.
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.5 The following precautionary statement pertains only to the test method portion, Sections 15 and 18, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 30-Jun-2010
• ICS: 91.100.30 - Concrete and concrete products
• Technical Committee: C09 - Concrete and Concrete Aggregates
• Drafting Committee: C09.42 - Fiber-Reinforced Concrete

Relations

• Replaces: ASTM C1116/C1116M-09 - Standard Specification for Fiber-Reinforced Concrete
• Effective Date: 01-Jul-2010
• Replaced By: ASTM C1116/C1116M-10a - Standard Specification for Fiber-Reinforced Concrete
• Effective Date: 01-Dec-2010
• Referred By: ASTM C505-19 - Standard Specification for Nonreinforced Concrete Irrigation Pipe with Rubber Gasket Joints
• Effective Date: 01-Jul-2010
• Referred By: ASTM C1613-22 - Standard Specification for Precast Concrete Gravity Grease Interceptor Tanks
• Effective Date: 01-Jul-2010
• Referred By: ASTM C507-22 - Standard Specification for Reinforced Concrete Elliptical Culvert, Storm Drain, and Sewer Pipe
• Effective Date: 01-Jul-2010
• Referred By: ASTM C14M-20 - Standard Specification for Nonreinforced Concrete Sewer, Storm Drain, and Culvert Pipe (Metric)
• Effective Date: 01-Jul-2010
• Referred By: ASTM C505M-19 - Standard Specification for Nonreinforced Concrete Irrigation Pipe With Rubber Gasket Joints (Metric)
• Effective Date: 01-Jul-2010
• Referred By: ASTM C14-20 - Standard Specification for Nonreinforced Concrete Sewer, Storm Drain, and Culvert Pipe
• Effective Date: 01-Jul-2010
• Referred By: ASTM C387/C387M-23 - Standard Specification for Packaged, Dry, Combined Materials for Concrete and High Strength Mortar
• Effective Date: 01-Jul-2010
• Referred By: ASTM C1504M-20 - Standard Specification for Manufacture of Precast Reinforced Concrete Three-Sided Structures for Culverts and Storm Drains (Metric)
• Effective Date: 01-Jul-2010
• Referred By: ASTM C1227-23 - Standard Specification for Precast Concrete Septic Tanks
• Effective Date: 01-Jul-2010
• Referred By: ASTM A820/A820M-22 - Standard Specification for Steel Fibers for Fiber-Reinforced Concrete
• Effective Date: 01-Jul-2010
• Referred By: ASTM C507M-22 - Standard Specification for Reinforced Concrete Elliptical Culvert, Storm Drain, and Sewer Pipe (Metric)
• Effective Date: 01-Jul-2010
• Referred By: ASTM C1670/C1670M-23 - Standard Specification for Adhered Manufactured Stone Masonry Veneer Units
• Effective Date: 01-Jul-2010
• Referred By: ASTM C412-19 - Standard Specification for Concrete Drain Tile
• Effective Date: 01-Jul-2010

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: C1116/C1116M – 10
Standard Specification for
1
Fiber-Reinforced Concrete
ThisstandardisissuedunderthefixeddesignationC1116/C1116M;thenumberimmediatelyfollowingthedesignationindicatestheyear
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope* A820/A820M Specification for Steel Fibers for Fiber-
Reinforced Concrete
1.1 This specification covers all forms of fiber-reinforced
C31/C31M Practice for Making and Curing Concrete Test
concrete that are delivered to a purchaser with the ingredients
Specimens in the Field
uniformly mixed, and that can be sampled and tested at the
C39/C39M Test Method for Compressive Strength of Cy-
point of delivery. It does not cover the placement, consolida-
lindrical Concrete Specimens
tion, curing, or protection of the fiber-reinforced concrete after
C42/C42M Test Method for Obtaining and Testing Drilled
delivery to the purchaser.
Cores and Sawed Beams of Concrete
1.2 Certain sections of this specification are also applicable
C94/C94M Specification for Ready-Mixed Concrete
to fiber-reinforced concrete intended for shotcreting by the
C125 Terminology Relating to Concrete and Concrete Ag-
dry-mix process when sampling and testing of concrete is
gregates
possible only at the point of placement. In this case, the
C138/C138M Test Method for Density (Unit Weight),
sections dealing with batching plant, mixing equipment, mix-
Yield, and Air Content (Gravimetric) of Concrete
ing and delivery, and measurement of workability and air
C143/C143M Test Method for Slump of Hydraulic-Cement
content, are not applicable.
Concrete
1.3 This specification does not cover thin-section glass
C150 Specification for Portland Cement
fiber-reinforcedconcretemanufacturedbythespray-upprocess
C172 Practice for Sampling Freshly Mixed Concrete
that is under the jurisdiction of ASTM Subcommittee C27.40.
C173/C173M Test Method for Air Content of Freshly
1.4 The values stated in either SI units or inch-pound units
Mixed Concrete by the Volumetric Method
are to be regarded separately as standard. The values stated in
C192/C192M Practice for Making and Curing Concrete
each system may not be exact equivalents; therefore, each
Test Specimens in the Laboratory
system shall be used independently of the other. Combining
C231 Test Method for Air Content of Freshly Mixed Con-
values from the two systems may result in non-conformance
crete by the Pressure Method
with the standard.
C387 Specification for Packaged, Dry, Combined Materials
1.5 The following precautionary statement pertains only to
for Mortar and Concrete
the test method portion, Sections 15 and 18, of this specifica-
C567 Test Method for Determining Density of Structural
tion: This standard does not purport to address all of the safety
Lightweight Concrete
concerns, if any, associated with its use. It is the responsibility
C666/C666M Test Method for Resistance of Concrete to
of the user of this standard to establish appropriate safety and
Rapid Freezing and Thawing
health practices and determine the applicability of regulatory
C684 Test Method for Making, Accelerated Curing, and
limitations prior to use.
Testing Concrete Compression Test Specimens
2. Referenced Documents
C685/C685M Specification for Concrete Made byVolumet-
2
ric Batching and Continuous Mixing
2.1 ASTM Standards:
C1077 Practice for Laboratories Testing Concrete and Con-
crete Aggregates for Use in Construction and Criteria for
1
This specification is under the jurisdiction of ASTM Committee C09 on
Laboratory Evaluation
Concrete and ConcreteAggregates and is the direct responsibility of Subcommittee
C1140 Practice for Preparing and Testing Specimens from
C09.42 on Fiber-Reinforced Concrete.
Shotcrete Test Panels
Current edition approved July 1, 2010. Published August 2010. Originally
C1385/C1385M Practice for Sampling Materials for Shot-
approved in 1989. Last previous edition approved in 2009 as C1116/C1116M–09.
DOI: 10.1520/C1116_C1116M-10.
crete
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
C1399 Test Method for Obtaining Average Residual-
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
Strength of Fiber-Reinforced Concrete
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
C1116/C1116M – 10
C1436 Specification for Materials for Sh
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:C1116/C1116M–09 Designation: C1116/C1116M – 10
Standard Specification for
1
Fiber-Reinforced Concrete
ThisstandardisissuedunderthefixeddesignationC1116/C1116M;thenumberimmediatelyfollowingthedesignationindicatestheyear
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
1.1 This specification covers all forms of fiber-reinforced concrete that are delivered to a purchaser with the ingredients
uniformlymixed,andthatcanbesampledandtestedatthepointofdelivery.Itdoesnotcovertheplacement,consolidation,curing,
or protection of the fiber-reinforced concrete after delivery to the purchaser.
1.2 Certain sections of this specification are also applicable to fiber-reinforced concrete intended for shotcreting by the dry-mix
process when sampling and testing of concrete is possible only at the point of placement. In this case, the sections dealing with
batching plant, mixing equipment, mixing and delivery, and measurement of workability and air content, are not applicable.
1.3 This specification does not cover thin-section glass fiber-reinforced concrete manufactured by the spray-up process that is
under the jurisdiction of ASTM Subcommittee C27.40.
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in non-conformance with the standard.
1.5 The following precautionary statement pertains only to the test method portion, Sections 15 and 18, of this specification:
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the
user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations
prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
A820/A820M Specification for Steel Fibers for Fiber-Reinforced Concrete
C31/C31M Practice for Making and Curing Concrete Test Specimens in the Field
C39/C39M Test Method for Compressive Strength of Cylindrical Concrete Specimens
C42/C42M Test Method for Obtaining and Testing Drilled Cores and Sawed Beams of Concrete
C94/C94M Specification for Ready-Mixed Concrete
C125 Terminology Relating to Concrete and Concrete Aggregates
C138/C138M Test Method for Density (Unit Weight), Yield, and Air Content (Gravimetric) of Concrete
C143/C143M Test Method for Slump of Hydraulic-Cement Concrete
C150 Specification for Portland Cement
C172 Practice for Sampling Freshly Mixed Concrete
C173/C173M Test Method for Air Content of Freshly Mixed Concrete by the Volumetric Method
C192/C192M Practice for Making and Curing Concrete Test Specimens in the Laboratory
C231 Test Method for Air Content of Freshly Mixed Concrete by the Pressure Method
C387 Specification for Packaged, Dry, Combined Materials for Mortar and Concrete
C567 Test Method for Determining Density of Structural Lightweight Concrete
C666/C666M Test Method for Resistance of Concrete to Rapid Freezing and Thawing
C684 Test Method for Making, Accelerated Curing, and Testing Concrete Compression Test Specimens
C685/C685M Specification for Concrete Made by Volumetric Batching and Continuous Mixing
1
This specification is under the jurisdiction of ASTM Committee C09 on Concrete and Concrete Aggregates and is the direct responsibility of Subcommittee C09.42 on
Fiber-Reinforced Concrete.
Current edition approved JuneJuly 1, 2009.2010. Published July 2009.August 2010. Originally approved in 1989. Last previous edition approved in 20082009 as
C1116/C1116M–08a.C1116/C1116M–09. DOI: 10.1520/C1116_C1116M-109.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
C1116/C1116M – 10
C1077 Practice for LaboratoriesTesting Concrete and ConcreteAggregates for Use in Const
...