iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D95-05e1

(Test Method)

Standard Test Method for Water in Petroleum Products and Bituminous Materials by Distillation

Standard Test Method for Water in Petroleum Products and Bituminous Materials by Distillation

SCOPE
1.1 This test method covers the determination of water in the range from 0 to 25 % volume in petroleum products, tars, and other bituminous materials by the distillation method.
Note 1—Volatile water-soluble material, if present, may be measured as water.
1.2 The specific products considered during the development of this test method are listed in Table 1. For bituminous emulsions refer to Test Method D 244. For crude oils, refer to Test Method D 4006 (API MPMS Chapter 10.2).
Note 2—With some types of oil, satisfactory results may be obtained from Test Method D 1796 (API MPMS Chapter 10.6).
1.3 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 6.

General Information

Status
Historical
Publication Date
31-May-2005
ICS
75.140 - Waxes, bituminous materials and other petroleum products
Technical Committee
D02 - Petroleum Products, Liquid Fuels, and Lubricants
Drafting Committee
D02.02 - Hydrocarbon Measurement for Custody Transfer (Joint ASTM-API)
Current Stage
Ref Project

Relations

Replaces
ASTM D95-05 - Standard Test Method for Water in Petroleum Products and Bituminous Materials by Distillation
Effective Date
01-Jun-2005
Replaced By
ASTM D95-05(2010) - Standard Test Method for Water in Petroleum Products and Bituminous Materials by Distillation
Effective Date
01-May-2010
Referred By
ASTM D2026/D2026M-15(2021)e1 - Standard Specification for Cutback Asphalt (Slow-Curing Type)
Effective Date
01-Jun-2005
Referred By
ASTM D2318-20 - Standard Test Method for Quinoline-Insoluble (QI) Content of Tar and Pitch
Effective Date
01-Jun-2005
Referred By
ASTM D4073/D4073M-06(2019)e1 - Standard Test Method for Tensile-Tear Strength of Bituminous Roofing Membranes
Effective Date
01-Jun-2005
Referred By
ASTM D3326-07(2017) - Standard Practice for Preparation of Samples for Identification of Waterborne Oils
Effective Date
01-Jun-2005
Referred By
ASTM D7665-22 - Standard Guide for Evaluation of Biodegradable Heat Transfer Fluids
Effective Date
01-Jun-2005
Referred By
ASTM D6224-22 - Standard Practice for In-Service Monitoring of Lubricating Oil for Auxiliary Power Plant Equipment
Effective Date
01-Jun-2005
Referred By
ASTM D7044-15 - Standard Specification for Biodegradable Fire Resistant Hydraulic Fluids
Effective Date
01-Jun-2005
Referred By
ASTM D1208-96(2019) - Standard Test Methods for Common Properties of Certain Pigments
Effective Date
01-Jun-2005
Referred By
ASTM D8125-18(2023) - Standard Specification for Re-Refined Engine Oil Bottoms (REOB)/Vacuum Tower Asphalt Extender (VTAE)
Effective Date
01-Jun-2005
Referred By
ASTM D2027/D2027M-19 - Standard Specification for Cutback Asphalt (Medium-Curing Type)
Effective Date
01-Jun-2005
Referred By
ASTM D7280-20 - Standard Test Method for Quinoline-Insoluble (QI) Content of Tar and Pitch by Stainless Steel Crucible Filtration
Effective Date
01-Jun-2005
Referred By
ASTM D4072-98(2018) - Standard Test Method for Toluene-Insoluble (TI) Content of Tar and Pitch
Effective Date
01-Jun-2005
Referred By
ASTM D2982-07(2019) - Standard Test Methods for Detecting Glycol-Base Antifreeze in Used Lubricating Oils
Effective Date
01-Jun-2005

Buy Standard

ASTM D95-05e1 - Standard Test Method for Water in Petroleum Products and Bituminous Materials by DistillationASTM D95-05e1 - Standard Test Method for Water in Petroleum Products and Bituminous Materials by Distillation
PreviousNext
Standard
ASTM D95-05e1 - Standard Test Method for Water in Petroleum Products and Bituminous Materials by Distillation
English language
6 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information.
Highway Transportation Standard
´1
Designation: D95 – 05 AASHTO No. T55
Designation: Manual of Petroleum Measurement Standards (MPMS), Chapter 10.5
Designation: 74/82 (88)
Standard Test Method for
Water in Petroleum Products and Bituminous Materials by
1
Distillation
ThisstandardisissuedunderthefixeddesignationD95;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1
´ NOTE—Table 4 formatting and the last sentence of 7.1 were updated editorially in August 2005.
1. Scope* D1796 Test Method forWater and Sediment in Fuel Oils by
the Centrifuge Method (Laboratory Procedure)
1.1 This test method covers the determination of water in
D4006 Test Method for Water in Crude Oil by Distillation
the range from 0 to 25 % volume in petroleum products, tars,
D4057 Practice for Manual Sampling of Petroleum and
and other bituminous materials by the distillation method.
Petroleum Products
NOTE 1—Volatile water-soluble material, if present, may be measured
D4177 Practice for Automatic Sampling of Petroleum and
as water.
Petroleum Products
1.2 The specific products considered during the develop-
D5854 PracticeforMixingandHandlingofLiquidSamples
ment of this test method are listed in Table 1. For bituminous
of Petroleum and Petroleum Products
emulsions refer to Test Method D244. For crude oils, refer to
E123 Specification forApparatus for Determination of Wa-
Test Method D4006 (API MPMS Chapter 10.2).
ter by Distillation
3
2.2 API Standards:
NOTE 2—With some types of oil, satisfactory results may be obtained
MPMS Chapter 8.1 Manual Sampling of Petroleum and
from Test Method D1796 (API MPMS Chapter 10.6).
Petroleum Products (ASTM Practice D4057)
1.3 The values stated in SI units are to be regarded as the
MPMS Chapter 8.2 Automatic Sampling of Petroleum and
standard. The values in parentheses are for information only.
Petroleum Products (ASTM Practice D4177)
1.4 This standard does not purport to address all of the
MPMSChapter8.3 MixingandHandlingofLiquidSamples
safety concerns, if any, associated with its use. It is the
of Petroleum and Petroleum Products (ASTM Practice
responsibility of the user of this standard to establish appro-
D5854)
priate safety and health practices and determine the applica-
MPMS Chapter 10.2 Determination of Water in Crude Oil
bility of regulatory limitations prior to use. For specific hazard
by the Distillation Method (ASTM Test Method D4006)
statements, see Section 6.
MPMSChapter10.6 TestMethodforWaterandSedimentin
Fuel Oils by the Centrifuge Method (Laboratory Proce-
2. Referenced Documents
dure) (ASTM Test Method D1796)
2
2.1 ASTM Standards:
D244 Test Methods and Practices for Emulsified Asphalts
3. Terminology
3.1 Definitions:
1
This test method is under the jurisdiction of ASTM Committee D02 on
3.1.1 bituminous material, n—in petroleum technology,a
Petroleum Products and Lubricants and theAPI Committee on Petroleum Measure-
black or dark-colored very viscous liquid or semi-solid com-
ment, and is the direct responsibility of Subcommittee D02.02 /COMQ, the joint
posed principally of high molecular weight condensed aro-
ASTM-API Committee on Static Petroleum Measurement.
CurrenteditionapprovedJune1,2005.PublishedJuly2005.Originallyapproved
matic, or naphthenic compounds, or both.
´1
in1921.Lastpreviouseditionapprovedin1999asD95–99 .DOI:10.1520/D0095-
05E01.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on Published as Manual of Petroleum Measurement Standards.Available from the
the ASTM website. American Petroleum Institute (API), 1220 L St., NW, Washington, DC 20005.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
´1
D95–05
4. Summary of Test Method 6.2 Solvent Blank—The water content of the solvent shall
be determined by distilling an equivalent amount of the same
4.1 The material to be tested is heated under reflux with a
solventusedforthetestsampleinthedistillationapparatusand
water-immiscible solvent, which co-distills with the water in
testingasoutlinedinSection10.Theblankshallbedetermined
the sample. Condensed solvent and water are continuously
to the nearest scale division and used to correct the volume of
separated in a trap, the water settling in the gra
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D4072-23(Test Method)
Standard Test Method for Toluene-Insoluble (TI) Content of Tar and Pitch

SIGNIFICANCE AND USE
5.1 This test method is useful for evaluating and characterizing tars and pitches and as one element in establishing the uniformity of shipments or sources of supply.
SCOPE
1.1 This test method covers the determination of toluene-insoluble matter (TI) in tar and pitch.  
1.2 Since this test method is empirical, strict adherence to all details of the procedure is necessary.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard information, see Section 8.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D3235-23(Test Method)
Standard Test Method for Solvent Extractables in Petroleum Waxes

SIGNIFICANCE AND USE
5.1 The solvent extractables in a wax may have significant effects on several of its properties such as strength, hardness, flexibility, scuff resistance, coefficient of friction, coefficient of expansion, melting point, and staining characteristics. Whether these effects are desirable or undesirable depends on the intended use of the wax.
SCOPE
1.1 This test method covers the determination of solvent extractables in petroleum waxes.  
1.2 The values stated in SI units are to be regarded as standard.  
1.2.1 Exception—The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM D5018-23(Test Method)
Standard Test Method for Shear Viscosity of Coal-Tar and Petroleum Pitches

SIGNIFICANCE AND USE
5.1 This test method is useful as one element in establishing the uniformity of shipments.  
5.2 Viscosity is also valuable for rheological characterization of binder pitches. Binder pitch imparts consistency to carbonaceous mixes and affects their resistance to deformation. Binder pitch viscosity is important for assessing mix consistency and for evaluating the ease of mix extrusion or molding into artifacts.
SCOPE
1.1 This test method covers the determination of the apparent shear viscosity of coal-tar and petroleum-based pitches having a Mettler softening point (SP) range of approximately 95 °C to 120 °C (see Test Method D3104).  
1.2 This test method is applicable only for rotational viscometers.  
1.3 Since this test method is based on theoretical grounds, strict adherence to details of the procedure is necessary to comply with the theoretical requirements.  
1.4 The values stated in SI units are to be regarded as standard.  
1.4.1 Exception—The values stated in conventional units (centipoise) are to be regarded as the standard for viscosity measurement only. The SI unit is the pascal second (Pa·s) and one millipascal second (mPa·s) = one centipoise (cP); centipoise is in cgs units.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in Section 8.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D95-23(Test Method)
Standard Test Method for Water in Petroleum Products and Bituminous Materials by Distillation

SIGNIFICANCE AND USE
5.1 A knowledge of the water content of petroleum products is important in the refining, purchase, sale, and transfer of products.  
5.2 The amount of water as determined by this test method (to the nearest 0.05 % or 0.1 % by volume, depending on the trap size used) may be used to correct the volume involved in the custody transfer of petroleum products and bituminous materials.  
5.3 The allowable amount of water may be specified in contracts.
SCOPE
1.1 This test method covers the determination of water in the range from 0 % to 25 % by volume in petroleum products, tars, and other bituminous materials by the distillation method.  
Note 1: Volatile water-soluble material, if present, may be measured as water.  
1.2 The specific products considered during the development of this test method are listed in Table 1. For bituminous emulsions refer to Test Method D244. For crude oils, refer to Test Method D4006 (API MPMS Chapter 10.2).
Note 2: With some types of oil, satisfactory results may be obtained from Test Method D1796 (API MPMS Chapter 10.6).  
1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 6.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM D2320-98(2022)e1(Test Method)
Standard Test Method for Density (Relative Density) of Solid Pitch (Pycnometer Method)

SIGNIFICANCE AND USE
5.1 Values of density and relative density are used for converting volumes to units of mass as required in other ASTM standards and in sales transactions.
SCOPE
1.1 This test method covers the determination of density and relative density by pycnometer, and can be used for pitch that can be handled in fragments.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D4715-98(2022)e1(Test Method)
Standard Test Method for Coking Value of Tar and Pitch (Alcan)

SIGNIFICANCE AND USE
4.1 This test method is useful for indicating the relative coke-forming propensities and for evaluating and characterizing tars and pitches. The test method can also be used as one element in establishing the uniformity of shipments or sources of supply.
SCOPE
1.1 This test method covers the determination of the coking value of tar and pitch having an ash content not over 0.5 %, as determined by Test Method D2415.  
1.2 Coking values by this test method are higher than those obtained by Test Method D2416. See the bias statement in Section 13.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D5442-17(2021)(Test Method)
Standard Test Method for Analysis of Petroleum Waxes by Gas Chromatography

SIGNIFICANCE AND USE
5.1 The determination of the carbon number distribution of petroleum waxes and the normal and non-normal hydrocarbons in each can be used for control of production processes as well as a guide to performance in many end uses.  
5.2 Data resulting from this test method are particularly useful in evaluating petroleum waxes for use in rubber formulations.
SCOPE
1.1 This test method covers the quantitative determination of the carbon number distribution of petroleum waxes in the range from n-C17 through n-C44 by gas chromatography using internal standardization. In addition, the content of normal and non-normal hydrocarbons for each carbon number is also determined. Material with a carbon number above n-C44 is determined by its difference from 100 % by mass and reported as C45+.  
1.2 This test method is applicable to petroleum derived waxes, including blends of waxes. This test method is not applicable to oxygenated waxes, such as synthetic polyethylene glycols (for example, Carbowax2), or natural products such as beeswax or carnauba.  
1.3 This test method is not directly applicable to waxes with oil content greater than 10 % as determined by Test Method D721.  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to consult and establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM D1465-10(2021)(Test Method)
Standard Test Method for Blocking and Picking Points of Petroleum Wax

SIGNIFICANCE AND USE
5.1 Blocking of waxed paper, because of the relatively low temperatures at which it may occur, can be a major problem to the paper-coating industry. For example, when the waxed surfaces in a roll of waxed paper stick together, upon separation the surface films are marred and the glossy finish is destroyed. The wax picking point and the wax blocking point indicate an approximate temperature range at or above which waxed surfaces in contact with each other are likely to cause surface film injury.
SCOPE
1.1 This test method covers the determination of the blocking point and picking point of petroleum wax.  
1.2 WARNING—Mercury has been designated by many regulatory agencies as a hazardous substance that can cause serious medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Use Caution when handling mercury and mercury-containing products. See the applicable product Safety Data Sheet (SDS) for additional information. The potential exists that selling mercury or mercury-containing products, or both, is prohibited by local or national law. Users must determine legality of sales in their location.  
1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are provided for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D4419-90(2021)(Test Method)
Standard Test Method for Measurement of Transition Temperatures of Petroleum Waxes by Differential Scanning Calorimetry (DSC)

SIGNIFICANCE AND USE
5.1 DSC in a convenient and rapid method for determining the temperature limits within which a wax undergoes during transitions. The highest temperature transition is a solid-liquid transition associated with complete melting; it can guide the choice of wax storage and application temperatures. The solid-solid temperature transition is related to the properties of the solid, that is, hardness and blocking temperature.
Note 2: For a relatively narrow cut petroleum wax, the lowest transition will be a solid-solid transition. A narrow cut wax is one obtained by deoiling a single petroleum distillate with a maximum range of 120 °F between its 5 % and 95 % vol in accordance with Test Method D1160 boiling points (converted to 760 torr). The DSC method cannot differentiate between solid-liquid and solid-solid transitions. Such information must be predetermined by other techniques. In the case of blends, the lower temperature transition may be envelopes of both solid-liquid and solid-solid transitions.  
5.2 Since petroleum wax is a mixture of hydrocarbons with different molecular weights, its transitions occur over a temperature range. This range is one factor that influences the width, expressed in °C, of the DSC peaks. The highest temperature transition is a first-order transition. If, for a series of waxes, there is supporting evidence that the highest temperature transition of each wax is the major first-order transition, its relative width should correlate with the relative width of the wax's molecular weight distribution.
SCOPE
1.1 This test method covers the transition temperatures of petroleum waxes, including microcrystalline waxes, by differential scanning calorimetry (DSC). These transitions may occur as a solid-solid transition or as a solid-liquid transition.  
1.2 The normal operating temperature range extends from 15 °C to 150 °C (Note 1).  
1.3 The values stated in SI units are to be regarded as the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D2269-10(2020)(Test Method)
Standard Test Method for Evaluation of White Mineral Oils by Ultraviolet Absorption

SIGNIFICANCE AND USE
5.1 The ultraviolet absorption of white mineral oils is used to determine their suitability for use in food, drug, and cosmetic applications.  
5.2 The U.S. Pharmacopeia and the National Formulary specifications for mineral oil require the measurement of ultraviolet absorption.
SCOPE
1.1 This test method describes a procedure for the examination and evaluation of NF and USP grade white mineral oils.  
1.2 This test method is not applicable to oils containing additives soluble in dimethyl sulfoxide (DMSO) that exhibit fluorescence or fluorescence quenching properties.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see 7.1.1 – 7.1.3.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off