ASTM D7344-11a
(Test Method)Standard Test Method for Distillation of Petroleum Products at Atmospheric Pressure (Mini Method)
Standard Test Method for Distillation of Petroleum Products at Atmospheric Pressure (Mini Method)
SIGNIFICANCE AND USE
The distillation (volatility) characteristics of hydrocarbons have an important effect on their safety and performance, especially in the case of fuels and solvents. The boiling range gives information on the composition, the properties, and the behavior of the fuel during storage and use. Volatility is the major determinant of the tendency of a hydrocarbon mixture to produce potentially explosive vapors.
The distillation characteristics are equally important for both automotive and aviation gasolines, affecting starting, warm-up, and tendency to vapor lock at high operating temperatures or high altitude, or both. The presence of high boiling point components in these and other fuels can significantly affect the degree of formation of solid combustion deposits.
Volatility, as it affects the rate of evaporation, is an important factor in the application of many solvents, particularly those used in paints.
Distillation limits are often included in petroleum product specifications, in commercial contract agreements, process refinery/control applications, and for compliance to regulatory rules.
SCOPE
1.1 This test method covers the procedure for the determination of the distillation characteristics of petroleum products in the range of 20 to 400°C (68 to 752°F) using miniaturized automatic distillation apparatus.
1.2 This test method is applicable to such products as: light and middle distillates, automotive spark-ignition engine fuels, automotive spark-ignition engine fuels containing up to 10 % ethanol, aviation gasolines, aviation turbine fuels, regular and low sulfur diesel fuels, biodiesel blends up to 20 % biodiesel, special petroleum spirits, naphthas, white spirits, kerosines, burner fuels, and marine fuels.
1.3 This test method is designed for the analysis of distillate products; it is not applicable to products containing appreciable quantities of residual material.
1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D7344 − 11a
StandardTest Method for
Distillation of Petroleum Products at Atmospheric Pressure
1
(Mini Method)
This standard is issued under the fixed designation D7344; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* D4177 Practice for Automatic Sampling of Petroleum and
Petroleum Products
1.1 This test method covers the procedure for the determi-
D4953 Test Method for Vapor Pressure of Gasoline and
nation of the distillation characteristics of petroleum products
Gasoline-Oxygenate Blends (Dry Method)
in the range of 20 to 400°C (68 to 752°F) using miniaturized
D5190 Test Method for Vapor Pressure of Petroleum Prod-
automatic distillation apparatus.
ucts (Automatic Method)
1.2 This test method is applicable to such products as: light
D5191 Test Method for Vapor Pressure of Petroleum Prod-
and middle distillates, automotive spark-ignition engine fuels,
ucts (Mini Method)
automotive spark-ignition engine fuels containing up to 10 %
D5482 Test Method for Vapor Pressure of Petroleum Prod-
ethanol, aviation gasolines, aviation turbine fuels, regular and
ucts (Mini Method—Atmospheric)
low sulfur diesel fuels, biodiesel blends up to 20 % biodiesel,
D6300 Practice for Determination of Precision and Bias
special petroleum spirits, naphthas, white spirits, kerosines,
Data for Use in Test Methods for Petroleum Products and
burner fuels, and marine fuels.
Lubricants
D6708 Practice for StatisticalAssessment and Improvement
1.3 This test method is designed for the analysis of distillate
products;itisnotapplicabletoproductscontainingappreciable of Expected Agreement Between Two Test Methods that
Purport to Measure the Same Property of a Material
quantities of residual material.
3
2.2 Energy Institute Standards:
1.4 The values stated in SI units are to be regarded as the
IP 69 Determination of Vapour Pressure—Reid Method
standard. The values given in parentheses are for information
IP 394 Determination of Air Saturated Vapour Pressure
only.
1.5 This standard does not purport to address all of the
3. Terminology
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appro-
3.1 Definitions:
priate safety and health practices and determine the applica-
3.1.1 decomposition, n—of a hydrocarbon, pyrolysis or
bility of regulatory limitations prior to use.
cracking of a molecule yielding smaller molecules with lower
boiling points than the original molecule.
2. Referenced Documents
3.1.1.1 decomposition point, n—in distillation,thecorrected
2
2.1 ASTM Standards:
temperature reading that coincides with the first indications of
D86 Test Method for Distillation of Petroleum Products at
thermal decomposition of the specimen.
Atmospheric Pressure
3.1.2 dynamic holdup, n—in D7344 distillation, amount of
D323 TestMethodforVaporPressureofPetroleumProducts
materialpresentinthedistillationcolumn,andinthecondenser
(Reid Method)
during the distillation.
D4057 Practice for Manual Sampling of Petroleum and
3.1.3 end point (EP) or final boiling point (FBP),
Petroleum Products
n—maximum corrected temperature reading obtained during
the test.
1
This test method is under the jurisdiction of ASTM Committee D02 on
Petroleum Products and Lubricants and is the direct responsibility of Subcommittee
3.1.4 initial boiling point (IBP), n—in D7344 distillation,
D02.08 on Volatility.
corrected temperature reading at the instant of the first detec-
Current edition approved Dec. 1, 2011. Published January 2012. Originally
tion of condensate in the receiver.
approved in 2007. Last previous edition approved in 2011 as D7344–11. DOI:
10.1520/D7344-11A.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on Available from Energy Institute, 61 New Cavendish St., London, WIG 7AR,
the ASTM website. U.K., http://www.energyinst.org.uk.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D7344 − 11a
3.1.5 percent evaporated, n—in distillation, sum of the 5. Significance and Use
percent recovered and the percent loss.
5.1 The distillation (volatility) characteristics of hydrocar-
3.1.6 percent loss, n— in distillation,onehundredminusthe bons have an important effect on their safety and performance,
percent total recovery.
es
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:D7344–11 Designation: D7344 – 11a
Standard Test Method for
Distillation of Petroleum Products at Atmospheric Pressure
1
(Mini Method)
This standard is issued under the fixed designation D7344; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This test method covers the procedure for the determination of the distillation characteristics of petroleum products in the
range of 20 to 400°C (68 to 752°F) using miniaturized automatic distillation apparatus.
1.2 This test method is applicable to such products as: light and middle distillates, automotive spark-ignition engine fuels,
automotive spark-ignition engine fuels containing up to 10 % ethanol, aviation gasolines, aviation turbine fuels, regular and low
sulfur diesel fuels, biodiesel blends up to 20 % biodiesel, special petroleum spirits, naphthas, white spirits, kerosines, burner fuels,
and marine fuels.
1.3 This test method is designed for the analysis of distillate products; it is not applicable to products containing appreciable
quantities of residual material.
1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D86 Test Method for Distillation of Petroleum Products at Atmospheric Pressure
D323 Test Method for Vapor Pressure of Petroleum Products (Reid Method)
D4057 Practice for Manual Sampling of Petroleum and Petroleum Products
D4177 Practice for Automatic Sampling of Petroleum and Petroleum Products
D4953 Test Method for Vapor Pressure of Gasoline and Gasoline-Oxygenate Blends (Dry Method)
D5190 Test Method for Vapor Pressure of Petroleum Products (Automatic Method)
D5191 Test Method for Vapor Pressure of Petroleum Products (Mini Method)
D5482 Test Method for Vapor Pressure of Petroleum Products (Mini MethodAtmospheric)
D6300 Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants
D6708 Practice for Statistical Assessment and Improvement of Expected Agreement Between Two Test Methods that Purport
to Measure the Same Property of a Material
3
2.2 Energy Institute Standards:
IP 69 Determination of Vapour Pressure—Reid Method
IP 394 Determination of Air Saturated Vapour Pressure
3. Terminology
3.1 Definitions:
3.1.1 charge volume, n—in petroleum products, in distillation, volume of the liquid sample transferred to the specimen
container.
3.1.2decomposition, n—of a hydrocarbon , pyrolysis or cracking of a molecule yielding smaller molecules with lower boiling
points than the original molecule.
3.1.2.1
1
This test method is under the jurisdiction of ASTM Committee D02 on Petroleum Products and Lubricants and is the direct responsibility of Subcommittee D02.08 on
Volatility.
Current edition approved JulyDec. 1, 2011. Published August 2011.January 2012. Originally approved in 2007. Last previous edition approved in 20082011 as
D7344–08.D7344–11. DOI: 10.1520/D7344-11A.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from Energy Institute, 61 New Cavendish St., London, WIG 7AR, U.K., http://www.energyinst.org.uk.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
D7344 – 11a
3.1.1.1 decomposition point, n—in distillation, the corrected temperature reading that coincides with the first indications of
thermal decomposition of the specimen.
3.1.3
3.1.2 dynamic holdup, n—in D7344 distillation, amount of material present in the distillation column, and in the condenser
during the distillation.
3.1.4
3.1.3 end point (EP) or final boiling point (FBP), n—maximum corrected temperature reading obtained during the test
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.