ASTM D2714-94(2014)
(Test Method)Standard Test Method for Calibration and Operation of the Falex Block-on-Ring Friction and Wear Testing Machine
Standard Test Method for Calibration and Operation of the Falex Block-on-Ring Friction and Wear Testing Machine
SIGNIFICANCE AND USE
4.1 This test method is used for the calibration of a block-on-ring testing machine by measuring the friction and wear properties of a calibration fluid under the prescribed test conditions.
4.2 The user of this test method should determine to his or her own satisfaction whether results of this test procedure correlate with field performance or other bench test machines. If the test conditions are changed, wear values can change and relative ratings of fluids can be different.
SCOPE
1.1 This test method covers the calibration and operation of a block-on-ring friction and wear testing machine.
1.2 The values in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D2714 − 94 (Reapproved 2014)
Standard Test Method for
Calibration and Operation of the Falex Block-on-Ring
1
Friction and Wear Testing Machine
This standard is issued under the fixed designation D2714; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope 3. Summary of Test Method
1.1 This test method covers the calibration and operation of 3.1 The test machine is operated using a steel test ring
a block-on-ring friction and wear testing machine. rotating against a steel test block, the specimen assembly being
partially immersed in the lubricant sample. The velocity of the
1.2 The values in SI units are to be regarded as standard.
test ring is 7.9 6 0.16 m/min (26 6 0.52 ft/min) which is
The values given in parentheses are mathematical conversions
equivalenttoaspindlespeedof72 61rpm.Thespecimensare
to SI units that are provided for information only.
subjected to 68 kg (150 lb) normal load applied by 6.8 kg
1.3 This standard does not purport to address all of the
(15 lb) of dead weight on the 10:1 ratio lever system. Test
safety concerns, if any, associated with its use. It is the
duration is 5000 cycles.
responsibility of the user of this standard to establish appro-
3.2 Three determinations are made: (1) The friction force
priate safety and health practices and determine the applica-
after a certain number of revolutions, (2) the average width of
bility of regulatory limitations prior to use.
the wear scar on the stationary block at the end of the test, and
2. Terminology (3)theweightlossforthestationaryblockattheendofthetest.
2.1 Definitions:
4. Significance and Use
2.1.1 coeffıcient of friction, µ or f—in tribology, the dimen-
sionlessratioofthefrictionforce(F)betweentwobodiestothe 4.1 This test method is used for the calibration of a
normal force (N) pressing these two bodies together. block-on-ring testing machine by measuring the friction and
wear properties of a calibration fluid under the prescribed test
µ or f 5 ~F/N! (1)
conditions.
2.1.1.1 Discussion—A distinction is often made between
static coeffıcient of friction and kinetic coeffıcient of friction.
4.2 The user of this test method should determine to his or
her own satisfaction whether results of this test procedure
2.1.2 friction force—the resisting force tangential to the
correlate with field performance or other bench test machines.
interface between two bodies when, under the action of an
If the test conditions are changed, wear values can change and
external force, one body moves or tends to move relative to the
relative ratings of fluids can be different.
other.
2.1.3 kinetic coeffıcient of friction—the coefficient of fric-
5. Apparatus
tion under conditions of macroscopic relative motion between
2
5.1 Falex Block-on-Ring Test Machine, shown in Fig. 1
two bodies.
and Fig. 2 and described in detail in Annex A1.
2.1.4 wear—damage to a solid surface, generally involving
progressive loss of material, due to relative motion between
NOTE 1—Consult the instruction manual for each machine to determine
respective capabilities and limitations.
that surface and a contacting substance or substances.
5.2 Analytical Balance, capable of weighing to the nearest
0.1 mg.
1
This test method is under the jurisdiction of ASTM Committee D02 on
Petroleum Products, Liquid Fuels, and Lubricants and is the direct responsibility of
5.3 Measuring Magnifier Glass, with SI or inch-pound
Subcommittee D02.L0.05 on Solid Lubricants.
calibration so that the scar width can be measured with a
This test method was prepared under the joint sponsorship of the American
precision of 0.01 mm, or equivalent.
Society of Lubrication Engineers with the cooperation of the Coordinating Research
Council, Inc. (CRC) Aviation Committee on Bonded Solid-Film Lubricants.
Accepted by ASLE September 1968.
CurrenteditionapprovedMay1,2014.PublishedJuly2014.Originallyapproved
2
in 1968. Last previous edition approved in 2009 as D2714–94(2009). DOI: Trademarked and manufactured by Falex Corp., 1020 Airpark Dr., Sugar
10.1520/D2714-94R14. Grove, IL 60554.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D2714 − 94 (2014)
7.3 Place the block holder on the block and carefully place
block and holder in upper specimen holder in test chamber.
Mount the test ring on the test shaft, taking care not to touch
the test area. Tighten the test ring on the shaft with 440 N
(100 lb
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D2714 − 94 (Reapproved 2009) D2714 − 94 (Reapproved 2014)
Standard Test Method for
Calibration and Operation of the Falex Block-on-Ring
1
Friction and Wear Testing Machine
This standard is issued under the fixed designation D2714; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope
1.1 This test method covers the calibration and operation of a block-on-ring friction and wear testing machine.
1.2 The values in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI
units that are provided for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Terminology
2.1 Definitions:
2.1.1 coeffıcient of friction, μ or f—in tribology, the dimensionless ratio of the friction force (F) between two bodies to the
normal force (N) pressing these two bodies together.
µ or f 5 F/N (1)
~ !
1
This test method is under the jurisdiction of ASTM Committee D02 on Petroleum Products Products, Liquid Fuels, and Lubricants and is the direct responsibility of
Subcommittee D02.L0.05 on Solid Lubricants.
This test method was prepared under the joint sponsorship of the American Society of Lubrication Engineers with the cooperation of the Coordinating Research Council,
Inc. (CRC) Aviation Committee on Bonded Solid-Film Lubricants.
Accepted by ASLE September 1968.
Current edition approved Oct. 1, 2009May 1, 2014. Published November 2009 July 2014. Originally approved in 1968. Last previous edition approved in 20032009 as
D2714–94(2003).D2714–94(2009). DOI: 10.1520/D2714-94R09.10.1520/D2714-94R14.
2.1.1.1 Discussion—
A distinction is often made between static coeffıcient of friction and kinetic coeffıcient of friction.
2.1.2 friction force—the resisting force tangential to the interface between two bodies when, under the action of an external
force, one body moves or tends to move relative to the other.
2.1.3 kinetic coeffıcient of friction—the coefficient of friction under conditions of macroscopic relative motion between two
bodies.
2.1.4 wear—damage to a solid surface, generally involving progressive loss of material, due to relative motion between that
surface and a contacting substance or substances.
3. Summary of Test Method
3.1 The test machine is operated using a steel test ring rotating against a steel test block, the specimen assembly being partially
immersed in the lubricant sample. The velocity of the test ring is 7.9 6 0.16 m/min (26 6 0.52 ft/min) which is equivalent to a
spindle speed of 72 6 1 rpm. The specimens are subjected to 68 kg (150 lb) normal load applied by 6.8 kg (15 lb) of dead weight
on the 10:1 ratio lever system. Test duration is 5000 cycles.
3.2 Three determinations are made: (1) The friction force after a certain number of revolutions, (2) the average width of the wear
scar on the stationary block at the end of the test, and (3) the weight loss for the stationary block at the end of the test.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D2714 − 94 (2014)
4. Significance and Use
4.1 This test method is used for the calibration of a block-on-ring testing machine by measuring the friction and wear properties
of a calibration fluid under the prescribed test conditions.
4.2 The user of this test method should determine to his or her own satisfaction whether results of this test procedure correlate
with field performance or other bench test machines. If the test conditions are changed, wear values can change and relative ratings
of fluids can be different.
5. Apparatus
2
5.1 Falex Block-on-Ring Test Machine, shown in Fig. 1 and Fig. 2 and described in detail in Annex A1.
NOTE 1—Consult the instruction manual for each machine to determine respective capabilities and limitations.
5.2 Analytical Balance, capable of weighing to the nearest 0.1 mg.
5.3 Measuring Magnifier Glass, with SI or inch-pound calibration
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.