ASTM C547-00

Standard Specification for Mineral Fiber Pipe Insulation

SCOPE
1.1 This specification covers mineral fiber insulation produced to form hollow cylinders for standard pipe and tubing sizes. The mineral fiber pipe insulation may be molded or precision v-grooved, with one or more walls split longitudinally for use on pipe temperatures up to 1200°F (650°C).
1.2 For satisfactory performance, properly installed protective vapor retarders or barriers should be used on sub-ambient temperature applications to reduce movement of moisture through or around the insulation to the colder surface. Failure to use a vapor barrier can lead to insulation and system damage. Refer to Practice C 921 to aid material selection.
1.3 Flexible mineral fiber wrap products such as perpendicular-oriented fiber insulation rolls, non-precision or manually scored block or board, or flexible boards or blankets used as pipe insulation, are not covered by this specification.
1.4 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
1.5 The following safety hazards caveat applies to the test methods portion, Section 11, only: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 09-Nov-2000
• ICS: 91.100.60 - Thermal and sound insulating materials
• Technical Committee: C16 - Thermal Insulation
• Drafting Committee: C16.20 - Homogeneous Inorganic Thermal Insulations

Relations

• Replaced By: ASTM C547-03 - Standard Specification for Mineral Fiber Pipe Insulation
• Effective Date: 10-Apr-2003
• Referred By: ASTM C1696-20 - Standard Guide for Industrial Thermal Insulation Systems
• Effective Date: 10-Nov-2000
• Referred By: ASTM C1558-19 - Standard Guide for Development of Standard Data Records for Computerization of Thermal Transmission Test Data for Thermal Insulation
• Effective Date: 10-Nov-2000
• Referred By: ASTM F683-23 - Standard Practice for Selection and Application of Thermal Insulation for Piping and Machinery
• Effective Date: 10-Nov-2000

Standards Content (Sample)

NOTICE: This standard has either been superceded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
Designation: C 547 – 00
Standard Specification for
1
Mineral Fiber Pipe Insulation
This standard is issued under the fixed designation C 547; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope C 302 Test Method for Density of Preformed Pipe-
2
Covering-Type Thermal Insulation
1.1 This specification covers mineral fiber insulation pro-
C 335 Test Method for Steady-State Heat Transfer Proper-
duced to form hollow cylinders for standard pipe and tubing
2
ties of Horizontal Pipe Insulation
sizes. The mineral fiber pipe insulation may be molded or
C 356 Test Method for Linear Shrinkage of Preformed
precision v-grooved, with one or more walls split longitudi-
High-Temperature Thermal Insulation Subjected to Soak-
nally for use on pipe temperatures up to 1200°F (650°C).
2
ing Heat
1.2 For satisfactory performance, properly installed protec-
C 390 Criteria for Sampling and Acceptance of Preformed
tive vapor retarders or barriers should be used on sub-ambient
2
Thermal Insulation Lots
temperature applications to reduce movement of moisture
C 411 Test Method for Hot-Surface Performance of High-
through or around the insulation to the colder surface. Failure
2
Temperature Thermal Insulation
to use a vapor barrier can lead to insulation and system
C 447 Practice for Estimating the Maximum Use Tempera-
damage. Refer to Practice C 921 to aid material selection.
2
ture of Insulations
1.3 Flexible mineral fiber wrap products such as
C 585 Practice for Inner and Outer Diameters of Rigid
perpendicular-oriented fiber insulation rolls, non-precision or
Thermal Insulation for Nominal Sizes of Pipe and Tubing
manually scored block or board, or flexible boards or blankets
2
(NPS System)
used as pipe insulation, are not covered by this specification.
C 612 Specification for Mineral Fiber Block and Board
1.4 The values stated in inch-pound units are to be regarded
2
Thermal Insulation
as the standard. The values given in parentheses are for
C 795 Specification for Thermal Insulation for Use in Con-
information only.
2
tact with Austenitic Stainless Steel
1.5 The following safety hazards caveat applies to the test
C 921 Practice for Determining the Properties of Jacketing
methods portion, Section 11, only: This standard does not
2
Materials for Thermal Insulation
purport to address all of the safety concerns, if any, associated
C 1045 Practice for Calculating Thermal Transmission
with its use. It is the responsibility of the user of this standard
2
Properties from Steady-State Heat Flux Measurements
to establish appropriate safety and health practices and
C 1058 Practice for Selecting Temperatures for Evaluating
determine the applicability of regulatory limitations prior to
2
and Reporting Thermal Properties of Thermal Insulation
use.
C 1104/C1104M Test Method for Determining the Water
2
2. Referenced Documents Vapor Sorption of Unfaced Mineral Fiber Insulation
E 84 Test Method for Surface Burning Characteristics of
2.1 ASTM Standards:
3
Building Materials
C 167 Test Methods for Thickness and Density of Blanket
2
2.2 Other Standards:
or Batt Thermal Insulations
UL 723 Tests for Surface Burning of Building Materials,
C 168 Terminology Relating to Thermal Insulating Materi-
2
available from Underwriters Laboratories, 333 Pfingsten
als
Road, Northbrook, IL 60062–2026
C 177 Test Method for Steady-State Heat Flux Measure-
NFPA 255 Method of Tests of Surface Burning Character-
ments and Thermal Transmission Properties by Means of
2
istics of Building Materials, available from the National
the Guarded-Hot-Plate Apparatus
Fire Protection Association, Batterymarch Park, Quincy,
MA 02269
1
This specification is under the jurisdiction of ASTM Committee C16 on
CAN/ULC-S102–M88 Standard Method of Test for Surface
Thermal Insulation and is the direct responsibility of Subcommittee C16.20 on
Burning Characteristics of Building Materials and Assem-
Homogeneous Inorganic Thermal Insulations.
blies, available from Underwriters Laboratories of
Current edition approved Nov. 10, 2000. Published January 2001. Originally
published as C 547 – 64 T to replace C 281 and C 300. Last previous edition
C 547 – 95.
2 3
Annual Book of ASTM Standards, Vol 04.06. Annual Book of ASTM Standards, Vol 04.07.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
NOTICE: This standard has either been superceded and replaced by a new version or discontinued.
Con
...