ASTM F2659-22

Standard Guide for Preliminary Evaluation of Comparative Moisture Condition of Concrete, Gypsum Cement and Other Floor Slabs and Screeds Using a Non-Destructive Electronic Moisture Meter

SIGNIFICANCE AND USE
5.1 Moisture in concrete floor slabs affects the performance of flooring systems such as resilient, wood, and textile floor coverings and coatings. Manufacturers of such systems generally require moisture testing be performed before installation of coverings on floor slabs and screeds. The measurement of sub-surface comparative moisture condition in the upper 1.0 in. (25.4 mm) stratum of a concrete slab with a non-destructive moisture meter is one such method.  
5.2 Excessive moisture in floor slabs after installation can cause floor covering system failures such as delamination, bonding failure, deterioration of finish flooring and coatings, and microbial growth.  
5.3 5.3 Comparative moisture content tests indicate the moisture in the slab, which is usually referenced to the percentage of dry weight. That is:
Results indicate conditions at the time of the test.  
5.4 Methods of meter calibration and factors affecting equilibration are described in Section 8.
SCOPE
1.1 This guide focuses on obtaining the comparative moisture condition within the upper 1.0 in. (25.4 mm) stratum in concrete, gypsum, anhydrite floor slabs and screeds for field tests. Due to the wide variation of material mixtures and additives used in floor slabs and screeds, this methodology may not be appropriate for all applications. See 1.2 through 1.8 and Section 11. Where appropriate or when specified, use further testing as outlined in Test Methods F1869 or F2170 before installing a resilient floor covering.  
1.2 This guide is intended for use to determine if there are moisture-related conditions existing on, or in, the floor slabs that could adversely impact the successful application and performance of resilient flooring products.  
1.3 This guide may be used to aid in the diagnosis of failures of installed resilient flooring.  
1.4 This guide is intended to be used in conjunction with meter manufacturer’s operation instructions and interpretive data where available.  
1.5 Where possible or when results need to be quantified, use this guide to determine where additional testing such as Test Methods F1869 or F2170 as specified to characterize the floor slab and the test area environment for moisture, humidity and temperature conditions.  
1.6 This guide may not be suitable for areas that have surface applied moisture migration systems, curing compounds or coatings that cannot be removed or cleaned off sufficiently to allow the moisture to move upwards through the slab. For a floor slab of 6 in. (150 mm) plus thickness, low porosity slabs, slabs with no vapor retarder installed, and slabs where the above surface environmental conditions can have a greater than normal influence on the moisture reduction gradient of the floor slab or screed, consider Test Method F2170 (below surface in situ rh method) as a more suitable test method under these circumstances.  
1.7 This guide is not intended to provide quantitative results as a basis for acceptance of a floor for installation of moisture sensitive flooring finishes systems. Test Methods F1869 or F2170 provide quantitative information for determining if moisture levels are within specific limits. Results from this guide do not provide vital information when evaluating thick slabs, slabs without effective vapor retarders directly under the slab, lightweight aggregate concrete floors, and slabs with curing compound or sealers on the surface.  
1.8 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use...

General Information

• Status: Historical
• Publication Date: 14-Jun-2022
• ICS: 91.060.30 - Ceilings. Floors. Stairs
• Technical Committee: F06 - Resilient Floor Coverings
• Drafting Committee: F06.40 - Practices

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F2659 − 22
Standard Guide for
Preliminary Evaluation of Comparative Moisture Condition
of Concrete, Gypsum Cement and Other Floor Slabs and
1
Screeds Using a Non-Destructive Electronic Moisture Meter
This standard is issued under the fixed designation F2659; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope slab or screed, consider Test Method F2170 (below surface in
situ rh method) as a more suitable test method under these
1.1 This guide focuses on obtaining the comparative mois-
circumstances.
ture condition within the upper 1.0 in. (25.4 mm) stratum in
1.7 This guide is not intended to provide quantitative results
concrete, gypsum, anhydrite floor slabs and screeds for field
as a basis for acceptance of a floor for installation of moisture
tests. Due to the wide variation of material mixtures and
sensitive flooring finishes systems. Test Methods F1869 or
additives used in floor slabs and screeds, this methodology may
F2170 provide quantitative information for determining if
not be appropriate for all applications. See 1.2 through 1.8 and
moisture levels are within specific limits. Results from this
Section 11. Where appropriate or when specified, use further
guide do not provide vital information when evaluating thick
testing as outlined in Test Methods F1869 or F2170 before
slabs, slabs without effective vapor retarders directly under the
installing a resilient floor covering.
slab, lightweight aggregate concrete floors, and slabs with
1.2 This guide is intended for use to determine if there are
curing compound or sealers on the surface.
moisture-related conditions existing on, or in, the floor slabs
1.8 The values stated in inch-pound units are to be regarded
that could adversely impact the successful application and
as standard. The values given in parentheses are mathematical
performance of resilient flooring products.
conversions to SI units that are provided for information only
1.3 This guide may be used to aid in the diagnosis of
and are not considered standard.
failures of installed resilient flooring.
1.9 This standard does not purport to address all of the
1.4 This guide is intended to be used in conjunction with safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appro-
meter manufacturer’s operation instructions and interpretive
priate safety, health, and environmental practices and deter-
data where available.
mine the applicability of regulatory limitations prior to use.
1.5 Where possible or when results need to be quantified,
Specific warnings are given in Section 7.
use this guide to determine where additional testing such as
1.10 This international standard was developed in accor-
Test Methods F1869 or F2170 as specified to characterize the
dance with internationally recognized principles on standard-
floor slab and the test area environment for moisture, humidity
ization established in the Decision on Principles for the
and temperature conditions.
Development of International Standards, Guides and Recom-
mendations issued by the World Trade Organization Technical
1.6 This guide may not be suitable for areas that have
Barriers to Trade (TBT) Committee.
surface applied moisture migration systems, curing compounds
or coatings that cannot be removed or cleaned off sufficiently to
2. Referenced Documents
allow the moisture to move upwards through the slab. For a
2
floor slab of 6 in. (150 mm) plus thickness, low porosity slabs, 2.1 ASTM Standards:
D4259 Practice for Preparation of Concrete by Abrasion
slabs with no vapor retarder installed, and slabs where the
above surface environmental conditions can have a greater than Prior to Coating Application
F1869 Test Method for Measuring Moisture Vapor Emission
normal influence on the moisture reduction gradient of the floor
Rate of Concrete Subfloor Using Anhydrous Calcium
Chloride
1
This guide is under the jurisdiction of ASTM Committee F06 on Resilient Floor
2
Coverings and is the direct responsibility of Subcommittee F06.40 on Practices. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved June 15, 2022. Published July 2022. Originally contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
approved in 2010. Last previous edition approved in 2015 as F2659-10 (2015). DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/F2659-22. the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. U
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F2659 − 10 (Reapproved 2015) F2659 − 22
Standard Guide for
Preliminary Evaluation of Comparative Moisture Condition
of Concrete, Gypsum Cement and Other Floor Slabs and
1
Screeds Using a Non-Destructive Electronic Moisture Meter
This standard is issued under the fixed designation F2659; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This guide focuses on obtaining the comparative moisture condition within the upper 1.0 in. (25.4 mm) stratum in concrete,
gypsum, anhydrite floor slabs and screeds for field tests. Due to the wide variation of material mixtures and additives used in floor
slabs and screeds, this methodology may not be appropriate for all applications. See 1.2 through 1.8 and Section 11. Where
appropriate or when specified, use further testing as outlined in Test Methods F1869, or F2170 or F2420before installing a resilient
floor covering.
1.2 This guide is intended for use to determine if there are moisture-related conditions existing on, or in, the floor slabs that could
adversely impact the successful application and performance of resilient flooring products.
1.3 This guide may be used to aid in the diagnosis of failures of installed resilient flooring.
1.4 This guide is intended to be used in conjunction with meter manufacturer’s operation instructions and interpretive data where
available.
1.5 Where possible,possible or when results need to be quantified, use this standard guide to determine where additional testing
such as Test Methods F1869, F2170, oror F2170 F2420as specified to characterize the floor slab and the test area environment for
moisture, humidity and temperature conditions.
1.6 This guide may not be suitable for areas that have surface applied moisture migration systems, curing compounds or coatings
that cannot be removed or cleaned off sufficiently to allow the moisture to move upwards through the slab. For a floor slab of 6
in. (150 mm) plus thickness, low porosity slabs, slabs with no vapor retarder installed, and slabs where the above surface
environmental conditions can have a greater than normal influence on the moisture reduction gradient of the floor slab or screed,
consider Test Method F2170 (below surface in situ rh method) as a more suitable test method under these circumstances.
1.7 This guide is not intended to provide quantitative results as a basis for acceptance of a floor for installation of moisture
sensitive flooring finishes systems. Test Methods F1869, F2170, oror F2170 F2420provide quantitative information for
determining if moisture levels are within specific limits. Results from this guide do not provide vital information when evaluating
thick slabs, slabs without effective vapor retarders directly under the slab, lightweight aggregate concrete floors, and slabs with
curing compound or sealers on the surface.
1
This guide is under the jurisdiction of ASTM Committee F06 on Resilient Floor Coverings and is the direct responsibility of Subcommittee F06.40 on Practices.
Current edition approved May 1, 2015June 15, 2022. Published July 2015July 2022. Originally approved in 2010. Last previous edition approved in 20102015 as F2659-10.
F2659-10 (2015). DOI: 10.1520/F2659-10R15.10.1520/F2659-22.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F2659 − 22
1.8 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety safety, health, and healthenvironmental practices and determine the
applicability of regulatory limitations prior to use. Specific warnings are given in Section 7.
1.10 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Refer
...