iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D3039/D3039M-00e1

(Test Method)

Standard Test Method for Tensile Properties of Polymer Matrix Composite Materials

Standard Test Method for Tensile Properties of Polymer Matrix Composite Materials

SCOPE
1.1 This test method determines the in-plane tensile properties of polymer matrix composite materials reinforced by high-modulus fibers. The composite material forms are limited to continuous fiber or discontinuous fiber-reinforced composites in which the laminate is balanced and symmetric with respect to the test direction.
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the inch-pound units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
09-Apr-2000
ICS
49.025.40 - Rubber and plastics
Technical Committee
D30 - Composite Materials
Drafting Committee
D30.04 - Lamina and Laminate Test Methods
Current Stage
Ref Project

Relations

Replaces
ASTM D3039/D3039M-00 - Standard Test Method for Tensile Properties of Polymer Matrix Composite Materials
Effective Date
10-Apr-2000
Replaced By
ASTM D3039/D3039M-00e2 - Standard Test Method for Tensile Properties of Polymer Matrix Composite Materials
Effective Date
10-Apr-2000
Referred By
ASTM C364/C364M-16 - Standard Test Method for Edgewise Compressive Strength of Sandwich Constructions
Effective Date
10-Apr-2000
Referred By
ASTM D7205/D7205M-21 - Standard Test Method for Tensile Properties of Fiber Reinforced Polymer Matrix Composite Bars
Effective Date
10-Apr-2000
Referred By
ASTM D3479/D3479M-19(2023) - Standard Test Method for Tension-Tension Fatigue of Polymer Matrix Composite Materials
Effective Date
10-Apr-2000
Referred By
ASTM D5766/D5766M-23 - Standard Test Method for Open-Hole Tensile Strength of Polymer Matrix Composite Laminates
Effective Date
10-Apr-2000
Referred By
ASTM D5083-17 - Standard Test Method for Tensile Properties of Reinforced Thermosetting Plastics Using Straight-Sided Specimens
Effective Date
10-Apr-2000
Referred By
ASTM C1869-18(2023) - Standard Test Method for Open-Hole Tensile Strength of Fiber-Reinforced Advanced Ceramic Composites
Effective Date
10-Apr-2000
Referred By
ASTM D7565/D7565M-10(2017) - Standard Test Method for Determining Tensile Properties of Fiber Reinforced Polymer Matrix Composites Used for Strengthening of Civil Structures
Effective Date
10-Apr-2000
Referred By
ASTM D5813-04(2018) - Standard Specification for Cured-In-Place Thermosetting Resin Sewer Piping Systems
Effective Date
10-Apr-2000
Referred By
ASTM D6484/D6484M-20 - Standard Test Method for Open-Hole Compressive Strength of Polymer Matrix Composite Laminates
Effective Date
10-Apr-2000
Referred By
ASTM D7745-19 - Standard Practice for Testing Pultruded Composites
Effective Date
10-Apr-2000
Referred By
ASTM D8337/D8337M-21 - Standard Test Method for Evaluation of Bond Properties of FRP Composite Applied to Concrete Substrate using Single-Lap Shear Test
Effective Date
10-Apr-2000
Referred By
ASTM C1275-18 - Standard Test Method for Monotonic Tensile Behavior of Continuous Fiber-Reinforced Advanced Ceramics with Solid Rectangular Cross-Section Test Specimens at Ambient Temperature
Effective Date
10-Apr-2000
Referred By
ASTM D4762-18 - Standard Guide for Testing Polymer Matrix Composite Materials
Effective Date
10-Apr-2000

Buy Standard

ASTM D3039/D3039M-00e1 - Standard Test Method for Tensile Properties of Polymer Matrix Composite MaterialsASTM D3039/D3039M-00e1 - Standard Test Method for Tensile Properties of Polymer Matrix Composite Materials
PreviousNext
Standard
ASTM D3039/D3039M-00e1 - Standard Test Method for Tensile Properties of Polymer Matrix Composite Materials
English language
13 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
e1
Designation:D3039/D3039M–00
Standard Test Method for
1
Tensile Properties of Polymer Matrix Composite Materials
This standard is issued under the fixed designation D3039/D3039M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1
e NOTE—Eq 5 was revised editorially in December 2002.
1. Scope Properties and Equilibrium Conditioning of Polymer Ma-
4
trix Composite Materials
1.1 This test method determines the in-plane tensile prop-
5
E4 Practices for Force Verification of Testing Machines
erties of polymer matrix composite materials reinforced by
E6 Terminology Relating to Methods of Mechanical Test-
high-modulus fibers.The composite material forms are limited
5
ing
to continuous fiber or discontinuous fiber-reinforced compos-
E83 Practice for Verification and Classification of Exten-
ites in which the laminate is balanced and symmetric with
5
someters
respect to the test direction.
E111 TestMethodforYoung’sModulus,TangentModulus,
1.2 The values stated in either SI units or inch-pound units
5
and Chord Modulus
are to be regarded separately as standard. Within the text, the
E122 Practice for Choice of Sample Size to Estimate a
inch-pound units are shown in brackets. The values stated in
6
Measure of Quality for a Lot or Process
each system are not exact equivalents; therefore, each system
E132 Test Method for Poisson’s Ratio at Room Tempera-
must be used independently of the other. Combining values
5
ture
from the two systems may result in nonconformance with the
E177 Practice for Use of the Terms Precision and Bias in
standard.
6
ASTM Test Methods
1.3 This standard does not purport to address all of the
E251 Test Methods for Performance Characteristics of
safety concerns, if any, associated with its use. It is the
5
Metallic Bonded Resistance Strain Gages
responsibility of the user of this standard to establish appro-
6
E456 Terminology Relating to Quality and Statistics
priate safety and health practices and determine the applica-
E691 Practice for Conducting an Interlaboratory Study to
bility of regulatory limitations prior to use.
6
Determine the Precision of a Test Method
2. Referenced Documents E1012 Practice for Verification of Specimen Alignment
5
Under Tensile Loading
2.1 ASTM Standards:
E 1237 Guide for Installing Bonded Resistance Strain
D792 TestMethodsforDensityandSpecificGravity(Rela-
5
2
Gages
tive Density) of Plastics by Displacement
2
D883 Terminology Relating to Plastics
3. Terminology
D2584 Test Method for Ignition Loss of Cured Reinforced
3
3.1 Definitions—TerminologyD3878definestermsrelating
Resins
to high-modulus fibers and their composites. Terminology
D2734 Test Method for Void Content of Reinforced Plas-
3
D883 defines terms relating to plastics. Terminology E6
tics
defines terms relating to mechanical testing. Terminology
D3171 Test Methods for Constituent Content of Compos-
4
E456 and Practice E177 define terms relating to statistics. In
ites Materials
4
the event of a conflict between terms, Terminology D3878
D3878 Terminology for Composite Materials
shall have precedence over the other standards.
D5229/D5229M Test Method for Moisture Absorption
3.2 Definitions of Terms Specific to This Standard:
NOTE—If the term represents a physical quantity, its
analytical dimensions are stated immediately following the
1
This test method is under the jurisidiction of ASTM Committee D30 on
term (or letter symbol) in fundamental dimension form, using
Composite Materials and is the direct responsibility of Subcommittee D30.04 on
Lamina and Laminate Test Methods.
the following ASTM standard symbology for fundamental
Current edition approved April 10, 2000. Published July 2000. Originally
published as D3039–71T. Last previous edition D3039–95a.
2
Annual Book of ASTM Standards, Vol 08.01.
3 5
Annual Book of ASTM Standards, Vol 08.02. Annual Book of ASTM Standards, Vol 03.01.
4 6
Annual Book of ASTM Standards, Vol 15.03. Annual Book of ASTM Standards, Vol 14.02.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
e1
D3039/D3039M–00
dimensions, shown within square brackets: [M] for mass, [L] 3.3.23 n—Poisson’s ratio.
for length, [T] for time, [Q] for thermodynamic temperature,
4. Summary of Test Method
and [nd] for nondimensional quantities. Use of these symbols
4.1 Athinflatstripofmaterialhavingaconstantrectangular
is restricted to analytical dimensions when used with square
brackets, as the symbols may hav
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D3518/D3518M-18(Test Method)
Standard Test Method for In-Plane Shear Response of Polymer Matrix Composite Materials by Tensile Test of a ±45° Laminate

SIGNIFICANCE AND USE
5.1 This test method is designed to produce in-plane shear property data for material specifications, research and development, quality assurance, and structural design and analysis. Factors that influence the shear response and should therefore be reported include the following: material, methods of material preparation and lay-up, specimen stacking sequence and overall thickness, specimen preparation, specimen conditioning, environment of testing, specimen alignment and gripping, speed of testing, time at temperature, void content, and volume percent reinforcement. Properties that may be derived from this test method include the following:  
5.1.1 In-plane shear stress versus shear strain response,  
5.1.2 In-plane shear chord modulus of elasticity,  
5.1.3 Offset shear properties,  
5.1.4 Maximum in-plane shear stress for a ±45° laminate, and  
5.1.5 Maximum in-plane engineering shear strain for a ±45° laminate.
SCOPE
1.1 This test method determines the in-plane shear response of polymer matrix composite materials reinforced by high-modulus fibers. The composite material form is limited to a continuous-fiber-reinforced composite ±45° laminate capable of being tension tested in the laminate x direction.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.2.1 Within the text, the inch-pound units are shown in brackets.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM D8101/D8101M-18(Test Method)
Standard Test Method for Measuring the Penetration Resistance of Composite Materials to Impact by a Blunt Projectile

SIGNIFICANCE AND USE
5.1 Advanced composite systems are used in a number of applications as shields to prevent penetration by projectiles. In general, the use of composites is more effective for blunt, rather than sharp, projectiles or in hybrid systems in which an additional shield can be used to blunt a sharp projectile. Knowledge of the penetration impact resistance of different material systems or the effects of environmental or in-service load exposure to the penetration resistance of given materials is useful for product development and material selection.  
5.2 An impact test used to measure the penetration resistance of a material can serve the following purposes:  
5.2.1 To quantify the effect of fiber architecture, stacking sequence, fiber and matrix material selection, and processing parameters on the penetration resistance of different composite materials;  
5.2.2 To measure the effects of environmental or in-service load exposure on the penetration impact resistance of a given material system; and  
5.2.3 As a tool for quality assurance requirements for materials designed for penetration resistance applications.  
5.3 The penetration resistance values obtained with this test method are most commonly used in material specification and selection and research and development activities. The data are not intended for use in establishing design allowables, as the results are specific to the geometry and physical conditions tested and are not generally scalable to other configurations.  
5.4 The reporting section requires items that tend to influence the penetration resistance of material systems. These include the following: fiber and matrix materials, fiber architecture, layup sequence, methods of material fabrication, environmental exposure parameters, specimen geometry and overall thickness, void content, specimen conditioning, testing environment and exposure time, specimen fixture and alignment, projectile mass and geometry, and projectile orientation at impact. Addit...
SCOPE
1.1 This test method measures the resistance of flat composite panels in one specific clamping configuration to penetration by a blunt projectile in free flight. In this test method, the term “penetration” is defined as the case in which the projectile travels completely through the composite panel and fully exits the back side. The composite materials may be continuous fiber angle-ply, woven or braided fiber-reinforced polymer matrix composites, or chopped fiber-reinforced composites. The resistance to penetration is quantified by a statistical function that defines the probability of penetration for a given kinetic energy.  
1.2 This test method is intended for composite test panels in which the thickness dimension is small compared with the test panel width and length (span to thickness on the order of 40 or greater).  
1.3 This test method is intended for applications such as jet engine fan containment, open rotor engine blade containment, or other applications in which protection is needed for projectiles at velocities typically lower than seen in ballistic armor applications. The typical impact velocity that this test is intended for is in the range of 100 to 500 m/s [300 to 1500 ft/s], as opposed to higher velocities associated with armor penetration.  
1.4 A flat composite panel is fixed between a circular-shaped clamping fixture and a large base fixture each with a large coaxial hole defining a region of the panel that is subjected to impact in the direction normal to the plane of the flat panel by a blunt projectile. Clamping pressure is provided by 28 through bolts that pass through the front clamp, the test specimen, and the back plate. The mass, geometry, desired impact kinetic energy, and impact orientation of the projectile with respect to the panel are specified before the test. Equipment and procedures are required for measuring the actual impact velocity and orientation during the test. The impact pe...

  • Standard
    14 pages
    English language
    sale 15% off
  • Standard
    14 pages
    English language
    sale 15% off
ASTM
ASTM D3039/D3039M-17(Test Method)
Standard Test Method for Tensile Properties of Polymer Matrix Composite Materials

SIGNIFICANCE AND USE
5.1 This test method is designed to produce tensile property data for material specifications, research and development, quality assurance, and structural design and analysis. Factors that influence the tensile response and should therefore be reported include the following: material, methods of material preparation and lay-up, specimen stacking sequence, specimen preparation, specimen conditioning, environment of testing, specimen alignment and gripping, speed of testing, time at temperature, void content, and volume percent reinforcement. Properties, in the test direction, which may be obtained from this test method include the following:  
5.1.1 Ultimate tensile strength,  
5.1.2 Ultimate tensile strain,  
5.1.3 Tensile chord modulus of elasticity,  
5.1.4 Poisson's ratio, and  
5.1.5 Transition strain.
SCOPE
1.1 This test method determines the in-plane tensile properties of polymer matrix composite materials reinforced by high-modulus fibers. The composite material forms are limited to continuous fiber or discontinuous fiber-reinforced composites in which the laminate is balanced and symmetric with respect to the test direction.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the inch-pound units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    13 pages
    English language
    sale 15% off
  • Standard
    13 pages
    English language
    sale 15% off
ASTM
ASTM E471-22(Test Method)
Standard Test Method for Obtaining Char Density Profile of Ablative Materials by Machining and Weighing

ABSTRACT
This test method covers the determination of the char density profile of a charred ablator. The total thickness of the char and degradation zone must be larger than the machining thicknesses required. Density variation throughout a charred ablator material is determined by successively measuring, machining, and weighing a sample of known size to obtain the density of the material removed by machining. The apparatus required for this method includes a laboratory balance capable of measuring to the nearest ten thousandth gram, and a machining technique capable of removing material in increments as small as a thousandth mm.
SCOPE
1.1 This test method covers the determination of the char density profile of a charred ablator that can be used with the following limitations:  
1.1.1 The local surface imperfections must be removed, and the char must be able to be machined off in a plane parallel to the char-virgin material interface before the density profiles can be determined.  
1.1.2 The char must be strong enough to withstand the machining and handling techniques employed.  
1.1.3 The material should have orderly density variations. The total thickness of the char and degradation zone must be larger than the machining thicknesses required.  
1.2 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.2.1 Exception—Certain inch-pound equivalent units are included in parentheses for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM F734-17(2022)(Test Method)
Standard Test Method for Shear Strength of Fusion Bonded Polycarbonate Aerospace Glazing Material

SIGNIFICANCE AND USE
5.1 At this writing, aerospace quality extruded transparent polycarbonate material is not available in thicknesses greater than 0.5 in. (12.7 mm). When a requirement exists for sheets thicker than 0.5 in. (12.7 mm), two or more sheets are fusion bonded together to form a single sheet of the desired thickness.  
5.2 The structural integrity of the completed transparency depends on the integrity of the fusion bond. This test applies torsional shear loads to measure the structural integrity of the fusion bond. This test method is considered more reliable and more reproducible than shear tests in tension or compression.
SCOPE
1.1 This test method determines the shear yield strength Fsy   and shear ultimate strength Fsu   of fusion bonds in polycarbonate by applying torsional shear loads to the fusion-bond line.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM F521-22(Test Method)
Standard Test Methods for Bond Integrity of Transparent Laminates

SIGNIFICANCE AND USE
4.1 These test methods provide a means to measure quantitatively the bond integrity between the outer layers of the transparency and the interlayer, or to measure the cohesive properties of the interlayer, under various loading conditions.  
4.2 These test methods provide empirical results useful for control purposes, correlation with service results, and as quality control tests for acceptance of production parts.  
4.3 Test results obtained on small, laboratory-size samples shown herein are indicative of full-size part capability, but not necessarily usable for design purposes.
SCOPE
1.1 These test methods cover determination of the bond integrity of transparent laminates. The laminates are usually made of two or more glass or hard plastic sheets held together by an elastomeric material. These test methods are intended to provide a means of determining the strength of the bond between the glass or plastic and the elastomeric interlayer under various mechanical or thermal loading conditions.  
1.2 The test methods appear as follows:    
Test Methods  
Sections  
Test Method A—Flatwise Bond Tensile Strength  
5 – 11  
Test Method B—Interlaminar Shear Strength  
12 – 17  
Test Method C—Creep Rupture  
18 – 25  
Test Method D—Thermal Exposure  
26 – 30  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    9 pages
    English language
    sale 15% off
  • Standard
    9 pages
    English language
    sale 15% off
ASTM
ASTM C1559-15(2021)(Test Method)
Standard Test Method for Determining Wicking of Fibrous Glass Blanket Insulation (Aircraft Type)

SIGNIFICANCE AND USE
5.1 The tendency of the insulation toward wicking can result in an increase in weight and a resultant potential degradation in the properties of the insulation.
SCOPE
1.1 This test method covers a laboratory procedure for evaluating the tendency of, aircraft type, fibrous glass blanket insulation to wick water.  
1.2 The wicking characteristics of materials can be affected by environmental conditions such as temperature and humidity. Values obtained as a result of this test method does not adequately describe the wicking characteristics of materials subject to conditions other than those indicated in the test method. (See Specification C800.)  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM C1511-15(2021)(Test Method)
Standard Test Method for Determining the Water Retention (Repellency) Characteristics of Fibrous Glass Insulation (Aircraft Type)

SIGNIFICANCE AND USE
5.1 The water retention of the insulation can result in an increase in weight and a resultant potential degradation in the properties of the insulation.
SCOPE
1.1 This test method covers a laboratory procedure for evaluating the water absorption potential of blanket insulation for aircraft, thereby providing a measure of potential weight increase due to water retention in an aircraft.  
1.2 The water repellency (or retention) characteristics of materials can be affected by conditions such as contamination or temperature of the water. Values obtained as a result of this test method does not adequately describe the water repellency characteristics of materials subject to these conditions.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM E2533-21(Guide)
Standard Guide for Nondestructive Examination of Polymer Matrix Composites Used in Aerospace Applications

SIGNIFICANCE AND USE
5.1 This guide references requirements that are intended to control the quality of NDT data. The purpose of this guide, therefore, is not to establish acceptance criteria and therefore approve composite materials or components for aerospace service.  
5.2 Following the discretion of the cognizant engineering organization, NDT for fracture control of composite and bonded materials should follow additional guidance described in MIL-HDBK-6870, NASA-STD-(I)-5019, or MSFC-RQMT-3479, or a combination thereof, as appropriate (not covered in this guide).  
5.3 Certain procedures referenced in this guide are written so they can be specified on the engineering drawing, specification, purchase order, or contract, for example, Practice E1742/E1742M (Radiography).  
5.4 Acceptance Criteria—Determination about whether a composite material or component meets acceptance criteria and is suitable for aerospace service should be made by the cognizant engineering organization. When examinations are performed in accordance with the referenced documents in this guide, the engineering drawing, specification, purchase order, or contract should indicate the acceptance criteria.  
5.4.1 Accept/reject criteria should consist of a listing of the expected kinds of imperfections and the rejection level for each.  
5.4.2 The classification of the articles under test into zones for various accept/reject criteria should be determined from contractual documents.  
5.4.3 Rejection of Composite Articles—If the type, size, or quantities of defects are found to be outside the allowable limits specified by the drawing, purchase order, or contract, the composite article should be separated from acceptable articles, appropriately identified as discrepant, and submitted for material review by the cognizant engineering organization, and dispositioned as (1) acceptable as is, (2) subject to further rework or repair to make the materials or component acceptable, or (3) scrapped when required by contractu...
SCOPE
1.1 This guide provides information to help engineers select appropriate nondestructive testing (NDT) methods to characterize aerospace polymer matrix composites (PMCs). This guide does not intend to describe every inspection technology. Rather, emphasis is placed on established NDT methods that have been developed into consensus standards and that are currently used by industry. Specific practices and test methods are not described in detail, but are referenced. The referenced NDT practices and test methods have demonstrated utility in quality assurance of PMCs during process design and optimization, process control, after manufacture inspection, in-service inspection, and health monitoring.  
1.2 This guide does not specify accept-reject criteria and is not intended to be used as a means for approving composite materials or components for service.  
1.3 This guide covers the following established NDT methods as applied to PMCs: Acoustic Emission (AE, Section 7); Computed Tomography (CT, Section 8); Leak Testing (LT, Section 9); Radiographic Testing, Computed Radiography, Digital Radiography, and Radioscopy (RT, CR, DR, RTR, Section 10); Shearography (Section 11); Strain Measurement (Contact Methods, Section 12); Thermography (Section 13); Ultrasonic Testing (UT, Section 14); and Visual Testing (VT, Section 15).  
1.4 The value of this guide consists of the narrative descriptions of general procedures and significance and use sections for established NDT practices and test methods as applied to PMCs. Additional information is provided about the use of currently active standard documents (an emphasis is placed on applicable standard guides, practices, and test methods of ASTM Committee E07 on Nondestructive Testing), geometry and size considerations, safety and hazards considerations, and information about physical reference standards.  
1.5 To ensure proper use of the referenced standard documents, there are recogni...

  • Guide
    49 pages
    English language
    sale 15% off
  • Guide
    49 pages
    English language
    sale 15% off
ASTM
ASTM E377-08(2020)(Practice)
Standard Practice for Internal Temperature Measurements in Low-Conductivity Materials

SIGNIFICANCE AND USE
2.1 Internal temperature measurements are made on both in-flight vehicles and on-ground test specimens; and, because of the importance of the temperature measurements to the design of various missile and spacecraft heat shields, it is essential that care be taken to minimize the sources of error in obtaining these measurements.  
2.2 Over the past several years, the problems of using thermocouples to obtain accurate temperature measurements in low-conductivity specimens have been studied by various people to isolate the sources of error and to establish improved temperature measurement techniques. The major sources of error are listed in this document and recommended solutions to the problems are given.
SCOPE
1.1 This practice covers methods for instrumenting low-conductivity specimens for testing in an environment subject to rapid thermal changes such as produced by rocket motors, atmospheric re-entry, electric-arc plasma heaters, and so forth. Specifically, practices for bare-wire thermocouple instrumentation applicable to sheath-type thermocouples are discussed.  
1.2 The values stated in inch-pound units are to be regarded as the standard. The metric equivalents of inch-pound units may be approximate.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off