ASTM D5971/D5971M-13
(Practice)Standard Practice for Sampling Freshly Mixed Controlled Low-Strength Material
Standard Practice for Sampling Freshly Mixed Controlled Low-Strength Material
SIGNIFICANCE AND USE
4.1 This practice shall be used to provide a representative sample of the material for the purpose of testing various properties. The procedures used in sampling shall include the use of every precaution that will assist in obtaining samples that are truly representative of the nature and condition of the CLSM.Note 2—The quality of the result produced by this standard is dependent on the competence of the personnel performing it and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice D3740 are generally considered capable of competent and objective testing/sampling/inspection/ and the like. Users of this standard are cautioned that compliance with Practice D3740 does not in itself assure reliable results. Reliable results depend on many factors. Practice D3740 provides a means of evaluating some of these factors.
SCOPE
1.1 This practice explains the procedure for obtaining a representative sample of freshly mixed controlled low-strength material (CLSM) as delivered to the project site on which tests are to be performed to determine compliance with quality requirements of the specifications under which the CLSM is furnished (Note 1). This practice includes sampling from revolving-drum truck mixers and from agitating equipment used to transport central-mixed CLSM. This Practice is based on Practice C172 for concrete.
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.Note 1—Composite samples are required by this practice unless specifically excepted by procedures governing the tests to be performed, such as tests to determine uniformity of consistency and mixer efficiency. Procedures used to select the specific test batches are not described in this practice. It is recommended that random sampling be used to determine overall specification compliance.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. (Warning—Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and tissue upon prolonged exposure.2)
1.4 This practice offers a set of instructions for performing one or more specific operations. This document cannot replace education or experience and should be used in conjunction with professional judgement. Not all aspects of this practice may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a projects many unique aspects. The word “standard” in the title of this document means only that the document has been approved through the ASTM consensus process.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D5971/D5971M − 13
Standard Practice for
1
Sampling Freshly Mixed Controlled Low-Strength Material
This standard is issued under the fixed designation D5971/D5971M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* judged, nor should this document be applied without consid-
eration of a projects many unique aspects. The word “stan-
1.1 This practice explains the procedure for obtaining a
dard” in the title of this document means only that the
representative sample of freshly mixed controlled low-strength
document has been approved through the ASTM consensus
material (CLSM) as delivered to the project site on which tests
process.
are to be performed to determine compliance with quality
requirements of the specifications under which the CLSM is
2. Referenced Documents
furnished (Note 1). This practice includes sampling from
3
2.1 ASTM Standards:
revolving-drum truck mixers and from agitating equipment
C172 Practice for Sampling Freshly Mixed Concrete
used to transport central-mixed CLSM. This Practice is based
D653 Terminology Relating to Soil, Rock, and Contained
on Practice C172 for concrete.
Fluids
1.2 The values stated in either SI units or inch-pound units
D3740 Practice for Minimum Requirements for Agencies
are to be regarded separately as standard. The values stated in
Engaged in Testing and/or Inspection of Soil and Rock as
each system may not be exact equivalents; therefore, each
Used in Engineering Design and Construction
system shall be used independently of the other. Combining
D4832 Test Method for Preparation and Testing of Con-
values from the two systems may result in non-conformance
trolled Low Strength Material (CLSM) Test Cylinders
with the standard.
D6023 Test Method for Density (Unit Weight), Yield, Ce-
ment Content, and Air Content (Gravimetric) of Con-
NOTE 1—Composite samples are required by this practice unless
specifically excepted by procedures governing the tests to be performed,
trolled Low-Strength Material (CLSM)
such as tests to determine uniformity of consistency and mixer efficiency.
D6103 Test Method for Flow Consistency of Controlled
Procedures used to select the specific test batches are not described in this
4
Low Strength Material (CLSM) (Withdrawn 2013)
practice. It is recommended that random sampling be used to determine
overall specification compliance.
3. Terminology
1.3 This standard does not purport to address all of the
3.1 Definitions—For common definitions of terms in this
safety concerns, if any, associated with its use. It is the
standard, refer to Terminology D653.
responsibility of the user of this standard to establish appro-
priate safety and health practices and determine the applica-
3.2 Definitions of Terms Specific to This Standard:
bility of regulatory limitations prior to use. (Warning—Fresh
3.2.1 composite sample, n—a sample that is constructed by
hydraulic cementitious mixtures are caustic and may cause
combiningequalportionsofgrabsamplestakenattwoormore
2
chemical burns to skin and tissue upon prolonged exposure. )
regularly spaced intervals during discharge of the middle
1.4 This practice offers a set of instructions for performing
portion of the batch of CLSM.
one or more specific operations. This document cannot replace
3.2.2 controlled low-strength material (CLSM), n—a mix-
education or experience and should be used in conjunction
ture of Portland cement, fly ash, aggregates, water, and
with professional judgement. Not all aspects of this practice
possibly chemical admixtures that, as the cement hydrates,
may be applicable in all circumstances. This ASTM standard is
forms a soil replacement material. The CLSM is a self
not intended to represent or replace the standard of care by
compacting, flowable, cementitious material that is primarily
which the adequacy of a given professional service must be
used as a backfill or structural fill instead of compacted fill or
unsuitable native soil. Depending on the amount of water used
1
This practice is under the jurisdiction of ASTM Committee D18 on Soil and
Rock and is the direct responsibility of Subcommittee D18.15 on Stabilization With
3
Admixtures. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Aug. 1, 2013. Published August 2013. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 1995. Last previous edition approved in 2007 as D5971 – 07. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/D5971-13. the ASTM website.
2 4
Section on Safety Precautio
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D5971 − 07 D5971/D5971M − 13
Standard Practice for
1
Sampling Freshly Mixed Controlled Low-Strength Material
This standard is issued under the fixed designation D5971;D5971/D5971M; the number immediately following the designation indicates
the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This practice explains the procedure for obtaining a representative sample of freshly mixed controlled low-strength material
(CLSM) as delivered to the project site on which tests are to be performed to determine compliance with quality requirements of
the specifications under which the CLSM is furnished (Note 1). This practice includes sampling from revolving-drum truck mixers
and from agitating equipment used to transport central-mixed CLSM. This Practice is based on Practice C172 for concrete.
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as the standard. The inch-pound
equivalents are shown for information only.standard. The values stated in each system may not be exact equivalents; therefore,
each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with
the standard.
NOTE 1—Composite samples are required by this practice unless specifically excepted by procedures governing the tests to be performed, such as tests
to determine uniformity of consistency and mixer efficiency. Procedures used to select the specific test batches are not described in this practice. It is
recommended that random sampling be used to determine overall specification compliance.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use. (Warning—Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and
2
tissue upon prolonged exposure. )
1.4 This practice offers a set of instructions for performing one or more specific operations. This document cannot replace
education or experience and should be used in conjunction with professional judgement. Not all aspects of this practice may be
applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the
adequacy of a given professional service must be judged, nor should this document be applied without consideration of a projects
many unique aspects. The word “standard” in the title of this document means only that the document has been approved through
the ASTM consensus process.
2. Referenced Documents
3
2.1 ASTM Standards:
C172 Practice for Sampling Freshly Mixed Concrete
D653 Terminology Relating to Soil, Rock, and Contained Fluids
D3740 Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in
Engineering Design and Construction
D4832 Test Method for Preparation and Testing of Controlled Low Strength Material (CLSM) Test Cylinders
D6023 Test Method for Density (Unit Weight), Yield, Cement Content, and Air Content (Gravimetric) of Controlled
Low-Strength Material (CLSM)
4
D6103 Test Method for Flow Consistency of Controlled Low Strength Material (CLSM) (Withdrawn 2013)
3. Terminology
3.1 Definitions—For common definitions of terms in this standard, refer to Terminology D653.
3.2 Definitions of Terms Specific to This Standard:
1
This practice is under the jurisdiction of ASTM Committee D18 on Soil and Rock and is the direct responsibility of Subcommittee D18.15 on Stabilization With
Admixtures.
Current edition approved Nov. 1, 2007Aug. 1, 2013. Published December 2007August 2013. Originally approved in 1995. Last previous edition approved in 20012007
as D5971 – 01.D5971 – 07. DOI: 10.1520/D5971-07.10.1520/D5971-13.
2
Section on Safety Precautions, Manual of Aggregate and Concrete Testing, Annual Book of ASTM Standards, Vol 04.02.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
4
The last approved version of this historical standard is referenced on www.astm.org.
*A Summary of Changes sect
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.