ASTM C1634-15
(Specification)Standard Specification for Concrete Facing Brick
Standard Specification for Concrete Facing Brick
ABSTRACT
This specification covers solid, dry-cast, concrete facing brick intended for interior and exterior use in constructing structural and facing masonry components and are made from portland cement, water, and suitable mineral aggregates with or without the inclusion of other materials. Concrete facing bricks shall be grouped into density classifications as either lightweight, medium weight, or normal weight. Specimens shall be sampled, tested, and conform accordingly to the specified physical requirements (oven-dry density, maximum water absorption, and minimum net area compressive strength) suitable for their density classification.
SCOPE
1.1 This specification covers solid, dry-cast, concrete facing brick intended for interior and exterior use in constructing structural and facing masonry components and are made from portland cement, water, and suitable mineral aggregates with or without the inclusion of other materials.
Note 1: Specification C55 addresses concrete building brick used in non-facing, utilitarian applications (previously referred to in earlier editions of Specification C55 as Grade S—for general use where moderate strength and resistance to frost action and moisture penetration are required). This specification differs from Specification C55 in that it includes expanded consideration for properties of concrete brick used in facing applications and other exposures (previously referred to in earlier editions of Specification C55 as Grade N—for use as architectural veneer and facing units in exterior walls and for use where high strength and resistance to moisture penetration and severe frost action are desired).
1.2 The text of this specification references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
Note 2: Concrete facing brick covered by this specification are made from lightweight or normal weight aggregates, or both.
Note 3: When particular features are desired, such as density classification, high compressive strength, surface textures for appearance or bond, finish, color, fire resistance, insulation, acoustical properties, or other special features, such properties should be specified separately by the purchaser. Suppliers should be consulted as to the availability of concrete facing brick having the desired features.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:C1634 −15
Standard Specification for
1
Concrete Facing Brick
This standard is issued under the fixed designation C1634; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* C55 Specification for Concrete Building Brick
C140 Test Methods for Sampling and Testing Concrete
1.1 This specification covers solid, dry-cast, concrete facing
Masonry Units and Related Units
brick intended for interior and exterior use in constructing
C150 Specification for Portland Cement
structural and facing masonry components and are made from
C331 Specification for LightweightAggregates for Concrete
portlandcement,water,andsuitablemineralaggregateswithor
Masonry Units
without the inclusion of other materials.
C426 Test Method for Linear Drying Shrinkage of Concrete
NOTE 1—Specification C55 addresses concrete building brick used in
Masonry Units
non-facing, utilitarian applications (previously referred to in earlier
C595 Specification for Blended Hydraulic Cements
editionsofSpecificationC55asGradeS—forgeneralusewheremoderate
C618 Specification for Coal Fly Ash and Raw or Calcined
strength and resistance to frost action and moisture penetration are
Natural Pozzolan for Use in Concrete
required). This specification differs from Specification C55 in that it
includes expanded consideration for properties of concrete brick used in
C989 Specification for Slag Cement for Use in Concrete and
facing applications and other exposures (previously referred to in earlier
Mortars
editions of Specification C55 as Grade N—for use as architectural veneer
C1157 Performance Specification for Hydraulic Cement
and facing units in exterior walls and for use where high strength and
C1232 Terminology of Masonry
resistance to moisture penetration and severe frost action are desired).
1.2 The text of this specification references notes and
3. Terminology
footnotes which provide explanatory material. These notes and
footnotes (excluding those in tables and figures) shall not be 3.1 Terminology defined in Terminology C1232 shall apply
considered as requirements of the standard.
for this specification.
1.3 The values stated in inch-pound units are to be regarded 3.2 Definitions of Terms Specific to This Standard:
as standard. The values given in parentheses are mathematical
3.2.1 concrete building brick, n—a concrete masonry unit,
conversions to SI units that are provided for information only
with a maximum width of four (4) inches and of a weight that
and are not considered standard.
will typically permit it to be lifted and placed with one hand,
that is manufactured for general use in non-facing, utilitarian
NOTE 2—Concrete facing brick covered by this specification are made
applications.
from lightweight or normal weight aggregates, or both.
NOTE 3—When particular features are desired, such as density
3.2.2 concrete facing brick, n—a concrete masonry unit,
classification, high compressive strength, surface textures for appearance
with a maximum width of four (4) inches and of a weight that
or bond, finish, color, fire resistance, insulation, acoustical properties, or
other special features, such properties should be specified separately by will typically permit it to be lifted and placed with one hand,
the purchaser. Suppliers should be consulted as to the availability of
that is manufactured to be typically used in an application
concrete facing brick having the desired features.
where one or more faces of the unit is intended to be exposed.
2. Referenced Documents
4. Materials and Manufacture
2
2.1 ASTM Standards:
4.1 Cementitious Materials—Materials shall conform to the
C33 Specification for Concrete Aggregates
following applicable specifications:
1 4.1.1 Portland Cement—Specification C150.
This specification is under the jurisdiction of ASTM Committee C15 on
Manufactured Masonry Units and is the direct responsibility of Subcommittee
4.1.2 Modified Portland Cement—Portland cement con-
C15.03 on Concrete Masonry Units and Related Units.
forming to Specification C150, modified as follows:
Current edition approved Sept. 1, 2015. Published September 2015. Originally
4.1.2.1 Limestone—Calcium carbonate, with a minimum
approved in 2006. Last previous edition approved in 2011 as C1634 – 11. DOI:
3
10.1520/C1634-15.
85 % CaCO content, is permitted to be added to the cement,
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
provided these requirements of Specification C150 as modified
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
are met:
Standards volume information, refer to the standard’s Document Summary page on
the
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C1634 − 11 C1634 − 15
Standard Specification for
1
Concrete Facing Brick
This standard is issued under the fixed designation C1634; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification covers solid, dry-cast, concrete facing brick intended for interior and exterior use in constructing structural
and facing masonry components and are made from portland cement, water, and suitable mineral aggregates with or without the
inclusion of other materials.
NOTE 1—Specification C55 addresses concrete building brick used in non-facing, utilitarian applications (previously referred to in earlier editions of
Specification C55 as Grade S—for general use where moderate strength and resistance to frost action and moisture penetration are required). This
specification differs from Specification C55 in that it includes expanded consideration for properties of concrete brick used in facing applications and other
exposures (previously referred to in earlier editions of Specification C55 as Grade N—for use as architectural veneer and facing units in exterior walls
and for use where high strength and resistance to moisture penetration and severe frost action are desired).
1.2 The text of this specification references notes and footnotes which provide explanatory material. These notes and footnotes
(excluding those in tables and figures) shall not be considered as requirements of the standard.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
NOTE 2—Concrete facing brick covered by this specification are made from lightweight or normal weight aggregates, or both.
NOTE 3—When particular features are desired, such as density classification, high compressive strength, surface textures for appearance or bond, finish,
color, fire resistance, insulation, acoustical properties, or other special features, such properties should be specified separately by the purchaser. Suppliers
should be consulted as to the availability of concrete facing brick having the desired features.
2. Referenced Documents
2
2.1 ASTM Standards:
C33 Specification for Concrete Aggregates
C55 Specification for Concrete Building Brick
C140 Test Methods for Sampling and Testing Concrete Masonry Units and Related Units
C150 Specification for Portland Cement
C331 Specification for Lightweight Aggregates for Concrete Masonry Units
C426 Test Method for Linear Drying Shrinkage of Concrete Masonry Units
C595 Specification for Blended Hydraulic Cements
C618 Specification for Coal Fly Ash and Raw or Calcined Natural Pozzolan for Use in Concrete
C989 Specification for Slag Cement for Use in Concrete and Mortars
C1157 Performance Specification for Hydraulic Cement
C1232 Terminology of Masonry
3. Terminology
3.1 Terminology defined in Terminology C1232 shall apply for this specification.
3.2 Definitions of Terms Specific to This Standard:
3.2.1 concrete building brick, n—a concrete masonry unit, with a maximum width of four (4) inches and of a weight that will
typically permit it to be lifted and placed with one hand, that is manufactured for general use in non-facing, utilitarian applications.
1
This specification is under the jurisdiction of ASTM Committee C15 on Manufactured Masonry Units and is the direct responsibility of Subcommittee C15.03 on
Concrete Masonry Units and Related Units.
Current edition approved June 1, 2011Sept. 1, 2015. Published June 2011September 2015. Originally approved in 2006. Last previous edition approved in 20092011 as
C1634 – 09.C1634 – 11. DOI: 10.1520/C1634-11.10.1520/C1634-15.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1634 − 15
3.2.2 concrete facing brick, n—a concrete masonry unit, with a maximum width of four (4) inches and of a weight that wi
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.