ASTM D4524-86(2005)
(Test Method)Standard Test Method for Composition of Plumage
Standard Test Method for Composition of Plumage
SIGNIFICANCE AND USE
This test method may be used for acceptance testing of commercial shipments of bulk plumage. Acceptance tolerances of content must be established between the purchaser and seller of bulk shipments of plumage, which also must comply with state and federal agency regulations, as appropriate.
5.1.1 In case of a dispute arising from differences in reported test results when using Test Method D 4524 for acceptance testing of commercial shipments, the purchaser and the supplier should conduct comparative tests to determine if there is a statistical bias between their laboratories. Competent statistical assistance is recommended for the investigation of bias. As a minimum, the two parties should take a group of test specimens that are as homogeneous as possible and that are from a lot of material of the type in question. The test specimens should then be randomly assigned in equal numbers to each laboratory for testing. The average results from the two laboratories should be compared using Student’t-test for unpaired data and an acceptable probability level chosen by the two parties before the testing is begun. If a bias is found, either its cause must be found and corrected or the purchaser and the supplier must agree to interpret test results in the light of the known bias.
This test method may also be applicable to the acceptance of consumer products that use plumage as a filling material. Such consumer products include pillows, comforters, sleeping bags, garments, furniture, and mattresses. Acceptance tolerances of content are established by distributors, importers, state or federal regulatory agencies. See 5.1.1.
SCOPE
1.1 This test method covers the quantitative determination of the components found in plumage. The test method is applicable for plumage found in bulk form or in finished consumer products.
1.2 The values stated in SI units are to be regarded as the standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D4524–86(Reapproved 2005)
Standard Test Method for
1
Composition of Plumage
This standard is issued under the fixed designation D4524; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 3. Terminology
1.1 This test method covers the quantitative determination 3.1 Definitions:
of the components found in plumage. The test method is 3.1.1 plumage, n—the outgrowth of fowl, consisting of
applicable for plumage found in bulk form or in finished feathers and down (waterfowl) or feathers only (nonwater-
consumer products. fowl).
1.2 The values stated in SI units are to be regarded as the 3.2 Forthedefinitionsoftermsusedinthisstandard,referto
standard. Terminology D123 and Terminology D4523.
1.3 This standard does not purport to address all of the
4. Summary of Test Method
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appro- 4.1 Arepresentative sample of plumage is selected from the
product being tested. The contents of the sample are identified
priate safety and health practices and determine the applica-
bility of regulatory limitations prior to use. and separated into component parts. Those component parts
are measured and reported as a percentage of the whole.
2. Referenced Documents
2
5. Significance and Use
2.1 ASTM Standards:
5.1 This test method may be used for acceptance testing of
D123 Terminology Relating to Textiles
D4523 Terminology Relating to Feather-Filled and Down- commercial shipments of bulk plumage.Acceptance tolerances
3
ofcontentmustbeestablishedbetweenthepurchaserandseller
Filled Products
2.2 Other Documents: of bulk shipments of plumage, which also must comply with
state and federal agency regulations, as appropriate.
Fed Std. No. 148a–1964 Method 2: Determination of Com-
4
position Feather Filling Materials 5.1.1 In case of a dispute arising from differences in
ABFLO: Quantitative Determination of Feather and reported test results when using Test Method D4524 for
5
acceptance testing of commercial shipments, the purchaser and
Down in Plumage
FTC Guides for the Feather and Down Products Industry, the supplier should conduct comparative tests to determine if
6
there is a statistical bias between their laboratories. Competent
1971
statistical assistance is recommended for the investigation of
bias.As a minimum, the two parties should take a group of test
specimens that are as homogeneous as possible and that are
1
This test method is under the jurisdiction ofASTM Committee D13 onTextiles
from a lot of material of the type in question. The test
and is the direct responsibility of Subcommittee D 13.61 on Apparel.
Current edition approved Sept. 1, 2005. Published December 2005. Originally specimens should then be randomly assigned in equal numbers
approved in 1986. Last previous edition approved in 2000 as D4524 – 86 (2000).
to each laboratory for testing.The average results from the two
DOI: 10.1520/D4524-86R05.
laboratories should be compared using Student’s t-test for
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
unpaireddataandanacceptableprobabilitylevelchosenbythe
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
two parties before the testing is begun. If a bias is found, either
the ASTM website.
its cause must be found and corrected or the purchaser and the
3
Withdrawn. The last approved version of this historical standard is referenced
supplier must agree to interpret test results in the light of the
on www.astm.org.
4
known bias.
Available from the General Services Administration Business Service Center,
1800 F Street, NW, Washington, DC 20407.
5.2 This test method may also be applicable to the accep-
5
Available from Association of Bedding and Law Officials, Texas Dept. of
tance of consumer products that use plumage as a filling
Health, 1100 W. 49th St., Austin, TX 78756.
6
material. Such consumer products include pillows, comforters,
Available from the Federal Trade Commission, 600 Pennsylvania Ave. N.W.,
Washington, DC 20580. sleeping bags, garments, furniture, and mattresses.Acceptance
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
D4524–86 (2005)
tolerances of content are established by distributors, importers, sample plumage to be analyzed. Another smaller mixing
state or federal regulatory agencies. See 5.1.1. container approximately
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.