ASTM D3786/D3786M-12
(Test Method)Standard Test Method for Bursting Strength of Textile Fabrics—Diaphragm Bursting Strength Tester Method
Standard Test Method for Bursting Strength of Textile Fabrics—Diaphragm Bursting Strength Tester Method
SIGNIFICANCE AND USE
5.1 This method for the determination of diaphragm bursting strength of knitted, nonwoven and woven fabrics is being used by the textile industry for the evaluation of a wide variety of end uses.
5.2 In cases where test results obtained using the procedures in Test Method D3786 have not been correlated with actual performance, Test Method D3786 is considered satisfactory for acceptance testing of commercial shipments of textile fabrics for bursting strength since the method has been used extensively in the trade for acceptance testing. In cases where disagreement arising from differences in values reported by the purchaser and the supplier when using Test Method D3786 for acceptance testing, the statistical bias, if any, between the laboratory of the purchaser and the laboratory of the supplier should be determined with comparison based on testing specimens randomly drawn from one sample of material of the type being evaluated.Note 2—The kind of load transfer and stretch that occur when knitted goods and nonwoven fabrics are worn are prevented by clamping them as described in this method.
SCOPE
1.1 This test method describes the measurement of the resistance of textile fabrics to bursting using a hydraulic or pneumatic diaphragm bursting tester. This test method is generally applicable to a wide variety of textile products.
1.2 This test method may also be applicable for stretch woven and woven industrial fabrics such as inflatable restraints.
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.Note 1—For the measurement of the bursting strength by means of a ball burst mechanism, refer to Test Method D3787.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D3786/D3786M − 12
StandardTest Method for
Bursting Strength of Textile Fabrics—Diaphragm Bursting
1
Strength Tester Method
This standard is issued under the fixed designation D3786/D3786M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope 2.2 Other Standard:
3
TAPPI Method T 403 , Bursting Strength of Paper
1.1 This test method describes the measurement of the
resistance of textile fabrics to bursting using a hydraulic or
3. Terminology
pneumatic diaphragm bursting tester. This test method is
3.1 For all terminology related to D13.59, Fabric Test
generally applicable to a wide variety of textile products.
Methods, see Terminology D4850.
1.2 This test method may also be applicable for stretch
3.1.1 The following terms are relevant to this standard:
woven and woven industrial fabrics such as inflatable re-
bursting strength, knitted fabric, nonwoven fabric, stretch
straints.
woven fabric, woven fabric.
1.3 The values stated in either SI units or inch-pound units
3.2 For all other terminology related to textiles, see Termi-
are to be regarded separately as standard. The values stated in
nology D123.
each system may not be exact equivalents; therefore, each
system shall be used independently of the other. Combining
4. Summary of Test Method
values from the two systems may result in non-conformance
4.1 A specimen is clamped over an expandable diaphragm.
with the standard.
The diaphragm is expanded by fluid pressure to the point of
NOTE 1—For the measurement of the bursting strength by means of a
specimen rupture. The difference between the total pressure
ball burst mechanism, refer to Test Method D3787.
required to rupture the specimen and the pressure required to
1.4 This standard does not purport to address all of the
inflate the diaphragm is reported as the bursting strength.
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appro- 5. Significance and Use
priate safety and health practices and determine the applica-
5.1 This method for the determination of diaphragm burst-
bility of regulatory limitations prior to use.
ing strength of knitted, nonwoven and woven fabrics is being
used by the textile industry for the evaluation of a wide variety
2. Referenced Documents
of end uses.
2
2.1 ASTM Standards:
5.2 In cases where test results obtained using the procedures
D123 Terminology Relating to Textiles
in Test Method D3786 have not been correlated with actual
D1776 Practice for Conditioning and Testing Textiles
performance,Test Method D3786 is considered satisfactory for
D3787 Test Method for Bursting Strength of Textiles—
acceptance testing of commercial shipments of textile fabrics
Constant-Rate-of-Traverse (CRT) Ball Burst Test
for bursting strength since the method has been used exten-
D4850 Terminology Relating to Fabrics and Fabric Test
sively in the trade for acceptance testing. In cases where
Methods
disagreement arising from differences in values reported by the
purchaser and the supplier when using Test Method D3786 for
acceptance testing, the statistical bias, if any, between the
1
This test method is under the jurisdiction ofASTM Committee D13 on Textiles
laboratory of the purchaser and the laboratory of the supplier
and is the direct responsibility of Subcommittee D13.59 on Fabric Test Methods,
General. should be determined with comparison based on testing speci-
Current edition approved Dec. 15, 2012. Published January 2013. Originally
mens randomly drawn from one sample of material of the type
approved in 1979. Last previous edition approved in 2009 as D3786–09. DOI:
being evaluated.
10.1520/D3786_D3786M-12.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on Available from TechnicalAssociation of the Pulp and Paper Industry (TAPPI),
the ASTM website. 15 Technology Parkway South, Norcross, GA 30092, http://www.tappi.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D3786/D3786M − 12
NOTE 2—The kind of load transfer and stretch that occur when knitted NOTE 5—Use of an aluminum sheet from one tester manufacturer may
goods and nonwoven fabrics are worn are prevented by clamping them as not be suitable for burst testing machine
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D3786/D3786M − 09 D3786/D3786M − 12
Standard Test Method for
Bursting Strength of Textile Fabrics—Diaphragm Bursting
1
Strength Tester Method
This standard is issued under the fixed designation D3786/D3786M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope
1.1 This test method describes the measurement of the resistance of textile fabrics to bursting using a hydraulic or pneumatic
diaphragm bursting tester. This test method is generally applicable to a wide variety of textile products.
1.2 This test method may also be applicable for stretch woven and woven industrial fabrics such as inflatable restraints.
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in non-conformance with the standard.
NOTE 1—For the measurement of the bursting strength by means of a ball burst mechanism, refer to Test Method D3787.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D123 Terminology Relating to Textiles
D1776 Practice for Conditioning and Testing Textiles
D3787 Test Method for Bursting Strength of Textiles—Constant-Rate-of-Traverse (CRT) Ball Burst Test
D4850 Terminology Relating to Fabrics and Fabric Test Methods
2.2 Other Standard:
3
TAPPI Method T 403,403 OM.91, Bursting Strength of Paper
3. Terminology
3.1 For all terminology related to D13.59, Fabric Test Methods, see Terminology D4850.
3.1.1 The following terms are relevant to this standard: bursting strength, knitted fabric, nonwoven fabric, stretch woven fabric,
woven fabric.
3.2 For all other terminology related to textiles, see Terminology D123.
4. Summary of Test Method
4.1 A specimen is clamped over an expandable diaphragm. The diaphragm is expanded by fluid pressure to the point of
specimen rupture. The difference between the total pressure required to rupture the specimen and the pressure required to inflate
the diaphragm is reported as the bursting strength.
1
This test method is under the jurisdiction of ASTM Committee D13 on Textiles and is the direct responsibility of Subcommittee D13.59 on Fabric Test Methods, General.
Current edition approved July 1, 2009Dec. 15, 2012. Published August 2009January 2013. Originally approved in 1979. Last previous edition approved in 20082009 as
D3786–08a.–09. DOI: 10.1520/D3786_D3786M-09.10.1520/D3786_D3786M-12.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from Technical Association of the Pulp and Paper Industry (TAPPI), 15 Technology Parkway South, Norcross, GA 30092, http://www.tappi.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D3786/D3786M − 12
5. Significance and Use
5.1 This method for the determination of diaphragm bursting strength of knitted, nonwoven and woven fabrics is being used
by the textile industry for the evaluation of a wide variety of end uses.
5.2 In cases where test results obtained using the procedures in Test Method D3786 have not been correlated with actual
performance, Test Method D3786 is considered satisfactory for acceptance testing of commercial shipments of textile fabrics for
bursting strength since the method has been used extensively in the trade for acceptance testing. In cases where disagreement
arising from differences in values reported by the purchaser and the supplier when using Test Method D3786 for acceptance testing,
the statistical bias, if any, between the laboratory of the purchaser and the laboratory of the supplier should be determined with
comp
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.