ASTM A283/A283M-12
(Specification)Standard Specification for Low and Intermediate Tensile Strength Carbon Steel Plates
Standard Specification for Low and Intermediate Tensile Strength Carbon Steel Plates
ABSTRACT
This specification covers four grades of carbon steel plates of structural quality for general application. Steel samples shall be melt processed by either open-hearth, basic-oxygen, or electric furnace. Heat and product analysis shall be performed wherein steel materials shall conform to required chemical compositions of carbon, manganese, phosphorus, sulfur, silicon, and copper. Steel specimens shall also undergo tensile tests and shall conform to required values of tensile strength, yield point, and elongation.
SCOPE
1.1 This specification2 covers two grades (C and D) of carbon steel plates of structural quality for general application.
1.2 When the steel is to be welded, a welding procedure suitable for the grade of steel and intended use or service is to be utilized. See Appendix X3 of Specification A6/A6M for information on weldability.
1.3 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exactly equivalents; therefore, each system is to be used independently of the other, without combining values in any way.
1.4 For plate produced from coil and furnished without heat treatment or with stress relieving only, the additional requirements, including additional testing requirements and the reporting of additional test results, of Specification A6/A6M apply.
1.5 This specification contains notes or footnotes, or both, that provide explanatory material. Such notes and footnotes, excluding those in tables and figures, do not contain any mandatory requirements.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:A283/A283M −12
StandardSpecification for
1
Low and Intermediate Tensile Strength Carbon Steel Plates
This standard is issued under the fixed designationA283/A283M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope* 3. General Requirements for Delivery
2
1.1 This specification covers two grades (C and D) of 3.1 Plates furnished under this specification shall con-form
carbon steel plates of structural quality for general application. to the requirements of the current edition of Specification
A6/A6M, for the specific date ordered, unless a conflict exists,
1.2 When the steel is to be welded, a welding procedure
in which case this specification shall prevail.
suitable for the grade of steel and intended use or service is to
be utilized. See Appendix X3 of Specification A6/A6M for 3.2 Coils are excluded from qualification to this specifica-
information on weldability. tion until they are processed into finished plates. Plates
produced from coil means plates that have been cut to
1.3 The values stated in either inch-pound units or SI units
individual lengths from a coil. The processor directly controls,
are to be regarded separately as standard. Within the text, the
or is responsible for, the operations involved in the processing
SI units are shown in brackets. The values stated in each
ofacoilintofinishedplates.Suchoperationsincludedecoiling,
system are not exactly equivalents; therefore, each system is to
leveling, cutting to length, testing, inspection, conditioning,
be used independently of the other, without combining values
heat treatment (if applicable), packaging, marking, loading for
in any way.
shipment, and certification.
1.4 For plate produced from coil and furnished without heat
NOTE 1—For plates produced from coil and furnished without heat
treatment or with stress relieving only, the additional
treatment or with stress relieving only, two test results are to be reported
requirements,includingadditionaltestingrequirementsandthe
foreachqualifyingcoil.Additionalrequirementsregardingplateproduced
reporting of additional test results, of Specification A6/A6M
from coil are described in Specification A6/A6M.
apply.
4. Process
1.5 This specification contains notes or footnotes, or both,
that provide explanatory material. Such notes and footnotes, 4.1 The steel shall be made by one or more of the following
excluding those in tables and figures, do not contain any processes: open-hearth, basic-oxygen, or electric-furnace.
mandatory requirements.
5. Chemical Requirements
2. Referenced Documents
5.1 The heat analysis shall conform to the requirements
3
2.1 ASTM Standards:
prescribed in Table 1.
A6/A6M Specification for General Requirements for Rolled
5.2 The steel shall conform on product analysis to the
Structural Steel Bars, Plates, Shapes, and Sheet Piling
requirements prescribed in Table 1, subject to the product
analysis tolerances in Specification A6/A6M.
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee
6. Mechanical Properties
A01.02 on Structural Steel for Bridges, Buildings, Rolling Stock and Ships.
Current edition approved Aug. 1, 2012. Published September 2012. Originally 6.1 Tensile Properties:
approved in 1946. Last previous edition approved in 2007 as A283/A283M – 03
6.1.1 Material as represented by the test specimens shall
(2007). DOI: 10.1520/A0283_A0283M-12.
conform to the requirements as to tensile properties prescribed
2
For ASME Boiler and Pressure Vessel Code applications, see related Specifi-
in Table 2.
cation SA-283/SA 283M in Section II of that Code.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
7. Keywords
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. 7.1 carbon steel; plates; structural quality
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
A283/A283M−12
TABLE 1 Chemical Requirements
Elements Heat Analysis, %
Grade C Grade D
Carbon, max 0.24 0.27
Manganese, max 0.90 0.90
Phosphorus, max 0.035 0.035
Sulfur, max 0.04 0.04
Silicon
1
Plates 1 ⁄2 in. [40 mm] and under, max 0.40 0.40
1
Plates over 1 ⁄2 in. [40 mm] 0.15–0.40 0.15–0.40
Copper, min %
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: A283/A283M − 03 (Reapproved 2007) A283/A283M − 12
Standard Specification for
1
Low and Intermediate Tensile Strength Carbon Steel Plates
This standard is issued under the fixed designation A283/A283M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
2
1.1 This specification covers four grades (A, B, C, two grades (C and D) of carbon steel plates of structural quality for general
application.
1.2 When the steel is to be welded, a welding procedure suitable for the grade of steel and intended use or service is to be
utilized. See Appendix X3 of Specification A6/A6M for information on weldability.
1.3 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units
are shown in brackets. The values stated in each system are not exactly equivalents; therefore, each system is to be used
independently of the other, without combining values in any way.
1.4 For plate produced from coil and furnished without heat treatment or with stress relieving only, the additional requirements,
including additional testing requirements and the reporting of additional test results, of Specification A6/A6M apply.
1.5 This specification contains notes or footnotes, or both, that provide explanatory material. Such notes and footnotes,
excluding those in tables and figures, do not contain any mandatory requirements.
2. Referenced Documents
3
2.1 ASTM Standards:
A6/A6M Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling
3. General Requirements for Delivery
3.1 Plates furnished under this specification shall con-form to the requirements of the current edition of Specification A6/A6M,
for the specific date ordered, unless a conflict exists, in which case this specification shall prevail.
3.2 Coils are excluded from qualification to this specification until they are processed into finished plates. Plates produced from
coil means plates that have been cut to individual lengths from a coil. The processor directly controls, or is responsible for, the
operations involved in the processing of a coil into finished plates. Such operations include decoiling, leveling, cutting to length,
testing, inspection, conditioning, heat treatment (if applicable), packaging, marking, loading for shipment, and certification.
NOTE 1—For plates produced from coil and furnished without heat treatment or with stress relieving only, two test results are to be reported for each
qualifying coil. Additional requirements regarding plate produced from coil are described in Specification A6/A6M.
4. Process
4.1 The steel shall be made by one or more of the following processes: open-hearth, basic-oxygen, or electric-furnace.
5. Chemical Requirements
5.1 The heat analysis shall conform to the requirements prescribed in Table 1.
5.2 The steel shall conform on product analysis to the requirements prescribed in Table 1, subject to the product analysis
tolerances in Specification A6/A6M.
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel, Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee A01.02
on Structural Steel for Bridges, Buildings, Rolling Stock and Ships.
Current edition approved Sept. 1, 2007Aug. 1, 2012. Published September 2007September 2012. Originally approved in 1946. Last previous edition approved in 20032007
as A283/A283M – 03.A283/A283M – 03 (2007). DOI: 10.1520/A0283_A0283M-03R07.10.1520/A0283_A0283M-12.
2
For ASME Boiler and Pressure Vessel Code applications, see related Specification SA-283/SA 283M in Section II of that Code.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
A283/A283M − 12
TABLE 1 Chemical Requirements
Elements Heat Analysis,
Grade A Grade B Grade C Grade
Carbon, max 0.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.