ASTM C92-95(2015)

Standard Test Methods for Sieve Analysis and Water Content of Refractory Materials

SIGNIFICANCE AND USE
3.1 Particle size distribution has a major affect upon most of the refractory properties. These test methods provide a means of measuring the distribution for the purpose of comparison to the desired distribution.  
3.2 These test methods also cover determination of the water content of refractory materials in the wet condition and of air-dried samples received, so that the sieve analysis can be calculated on the dry basis.  
3.3 These methods can produce data for specification acceptance, design purposes, manufacturing control, and research and development.  
3.4 A reference set of standard matched or calibrated sieves4 shall be provided for use in checking the set of sieves used in the actual sieve analysis of samples. The sieves for use in sieve analysis may also be standard matched sieves or may be unmatched sieves conforming to the Specification Table in Specification E11, provided that such sieves will give results that differ by no more than 5 % from those obtained with the reference set when the two sets are compared in accordance with the section of Test Method C429 on testing of sieves and samples splitters.
SCOPE
1.1 These test methods cover a wet and a dry method for sieve analysis of refractory materials.  
1.1.1 Wet Sieve Analysis—Water promotes the slaking of clays and helps to separate fine particles, washing them from the larger grains. This method is recommended for use with materials that require water addition, and that slake in normal industrial use.  
1.1.2 Dry Sieve Analysis—The dry method is not as effective as the wet method in determining the amount of material present in the smaller particle sizes. It is recommended (1) for clays, when the slaking action of water is undesirable, (2) when the material is in the form of coarsely ground grog and calcine, and (3) when the clay is to be used in such a way that the ultimate particle size is of secondary importance.  
1.2 These test methods also cover determination of the water content of refractory materials in the wet condition and of air-dried samples as received, so that the sieve analysis can be calculated on the dry basis. Included is a method for obtaining the water content of other refractory materials, such as plastic refractories and wet mixes.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 28-Feb-2015
• ICS: 81.080 - Refractories
• Technical Committee: C08 - Refractories
• Drafting Committee: C08.03 - Physical Properties

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: C92 − 95 (Reapproved 2015)
Standard Test Methods for
1
Sieve Analysis and Water Content of Refractory Materials
ThisstandardisissuedunderthefixeddesignationC92;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoptionor,inthecaseofrevision,theyearoflastrevision.Anumberinparenthesesindicatestheyearoflastreapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope 2. Referenced Documents
2
1.1 These test methods cover a wet and a dry method for 2.1 ASTM Standards:
sieve analysis of refractory materials. C429Test Method for Sieve Analysis of Raw Materials for
1.1.1 Wet Sieve Analysis—Water promotes the slaking of Glass Manufacture
clays and helps to separate fine particles, washing them from E11Specification forWovenWireTest Sieve Cloth andTest
the larger grains. This method is recommended for use with Sieves
materials that require water addition, and that slake in normal E105Practice for Probability Sampling of Materials
industrial use. E122PracticeforCalculatingSampleSizetoEstimate,With
1.1.2 Dry Sieve Analysis—The dry method is not as effec- Specified Precision, the Average for a Characteristic of a
tive as the wet method in determining the amount of material Lot or Process
present in the smaller particle sizes. It is recommended (1) for 2.2 Other Document:
3
clays,whentheslakingactionofwaterisundesirable,(2)when ASTM STP447Manual on Test Sieving Methods
thematerialisintheformofcoarselygroundgrogandcalcine,
3. Significance and Use
and (3) when the clay is to be used in such a way that the
3.1 Particlesizedistributionhasamajoraffectuponmostof
ultimate particle size is of secondary importance.
the refractory properties. These test methods provide a means
1.2 These test methods also cover determination of the
of measuring the distribution for the purpose of comparison to
water content of refractory materials in the wet condition and
the desired distribution.
of air-dried samples as received, so that the sieve analysis can
3.2 These test methods also cover determination of the
be calculated on the dry basis. Included is a method for
water content of refractory materials in the wet condition and
obtaining the water content of other refractory materials, such
of air-dried samples received, so that the sieve analysis can be
as plastic refractories and wet mixes.
calculated on the dry basis.
1.3 The values stated in inch-pound units are to be regarded
3.3 These methods can produce data for specification
as standard. The values given in parentheses are mathematical
acceptance, design purposes, manufacturing control, and re-
conversions to SI units that are provided for information only
search and development.
and are not considered standard.
4
3.4 Areferencesetofstandardmatchedorcalibratedsieves
1.4 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the shall be provided for use in checking the set of sieves used in
responsibility of the user of this standard to establish appro-
2
priate safety and health practices and determine the applica- For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
bility of regulatory limitations prior to use.
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
3
Available from ASTM International, 100 Barr Harbor Drive, West
1
These test methods are under the jurisdiction of ASTM Committee C08 on Conshohocken, PA 19428.
4
Refractories and are the direct responsibility of Subcommittee C08.03 on Physical The sole source of supply of matched sieves known to the committee at this
Properties. time is W. S. Tyler, Inc., Mentor, OH 44060. If you are aware of alternative
Current edition approved March 1, 2015. Published April 2015. Originally suppliers, please provide this information to ASTM International Headquarters.
approvedin1943.Lastpreviouseditionapprovedin2010asC92–95(2010).DOI: Your comments will receive careful consideration at a meeting of the responsible
1
10.1520/C0092-95R15. technical committee, which you may attend.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
C92 − 95 (2015)
theactualsieveanalysisofsamples.Thesievesforuseinsieve WET SIEVE ANALYSIS
analysis may also be standard matched sieves or may be
6. Dry Materials
unmatched sieves conforming to the Specification Table in
6.1 If the material is received in the dry condition, the test
Specification E11, provided that such sieves will give results
specimen (Note 1) shall consist of t
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C92 − 95 (Reapproved 2010) C92 − 95 (Reapproved 2015)
Standard Test Methods for
1
Sieve Analysis and Water Content of Refractory Materials
This standard is issued under the fixed designation C92; the number immediately following the designation indicates the year of original
adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope
1.1 These test methods cover a wet and a dry method for sieve analysis of refractory materials.
1.1.1 Wet Sieve Analysis—Water promotes the slaking of clays and helps to separate fine particles, washing them from the larger
grains. This method is recommended for use with materials that require water addition, and that slake in normal industrial use.
1.1.2 Dry Sieve Analysis—The dry method is not as effective as the wet method in determining the amount of material present
in the smaller particle sizes. It is recommended (1) for clays, when the slaking action of water is undesirable, (2) when the material
is in the form of coarsely ground grog and calcine, and (3) when the clay is to be used in such a way that the ultimate particle
size is of secondary importance.
1.2 These test methods also cover determination of the water content of refractory materials in the wet condition and of air-dried
samples as received, so that the sieve analysis can be calculated on the dry basis. Included is a method for obtaining the water
content of other refractory materials, such as plastic refractories and wet mixes.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
C429 Test Method for Sieve Analysis of Raw Materials for Glass Manufacture
E11 Specification for Woven Wire Test Sieve Cloth and Test Sieves
E105 Practice for Probability Sampling of Materials
E122 Practice for Calculating Sample Size to Estimate, With Specified Precision, the Average for a Characteristic of a Lot or
Process
2.2 Other Document:
3
ASTM STP 447 Manual on Test Sieving Methods
3. Significance and Use
3.1 Particle size distribution has a major affect upon most of the refractory properties. These test methods provide a means of
measuring the distribution for the purpose of comparison to the desired distribution.
3.2 These test methods also cover determination of the water content of refractory materials in the wet condition and of air-dried
samples received, so that the sieve analysis can be calculated on the dry basis.
3.3 These methods can produce data for specification acceptance, design purposes, manufacturing control, and research and
development.
1
These test methods are under the jurisdiction of ASTM Committee C08 on Refractories and are the direct responsibility of Subcommittee C08.03 on Physical Properties.
Current edition approved Nov. 1, 2010March 1, 2015. Published November 2010April 2015. Originally approved in 1943. Last previous edition approved in 20052010
as C92 – 95 (2005).(2010). DOI: 10.1520/C0092-95R10.10.1520/C0092-95R15.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from ASTM International, 100 Barr Harbor Drive, West Conshohocken, PA 19428.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
C92 − 95 (2015)
4
3.4 A reference set of standard matched or calibrated sieves shall be provided for use in checking the set of sieves used in the
actual sieve analysis of samples. The sieves for use in sieve analysis may also be standard matched sieves or may be unmatched
sieves conforming to the Specification Table in Specification E11, provided that such sieves will give results that differ by no
...