ASTM D2065-03(2017)
(Test Method)Standard Test Method for Determination of Edge Performance of Composite Wood Products Under Surfactant Accelerated Moisture Stress
Standard Test Method for Determination of Edge Performance of Composite Wood Products Under Surfactant Accelerated Moisture Stress
SIGNIFICANCE AND USE
5.1 This test method provides a measure of the dimensional stability and integrity of the coated edge of various composite wood products under accelerated moisture stress. It is widely used as an indicator or predictor of the anticipated performance of composite wood products during exterior exposure. It may be used for developmental evaluation of coatings, substrates, or both. It may also be useful for quality control or monitoring of the production of coated or uncoated composite wood products.
SCOPE
1.1 This test method is intended to serve as a means for measurement of swelling and cracking of the coated or uncoated edge of a composite wood substrate that has been subjected to wetting by a test solution containing surface active agent.
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: D2065 − 03 (Reapproved 2017)
Standard Test Method for
Determination of Edge Performance of Composite Wood
1
Products Under Surfactant Accelerated Moisture Stress
This standard is issued under the fixed designation D2065; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 3.1.1 crack rating, n—a numerical value on a scale from 1
to 10, with 10 representing no evidence of cracking of the edge
1.1 This test method is intended to serve as a means for
(see Test Method D661).
measurement of swelling and cracking of the coated or
3.1.2 composite wood products, n—boards or other struc-
uncoated edge of a composite wood substrate that has been
tural or decorative materials manufactured from wood fibers,
subjectedtowettingbyatestsolutioncontainingsurfaceactive
flakes or strands and various resin binders consolidated under
agent.
heat, or pressure, or both.
1.2 The values stated in SI units are to be regarded as the
standard. The values given in parentheses are for information
4. Summary of Test Method
only.
4.1 A surfactant solution is placed in a tray that contains a
1.3 This standard does not purport to address all of the
sponge. A preweighed and calipered panel with a coated edge
safety concerns, if any, associated with its use. It is the
is placed with the edge in contact with the surfactant saturated
responsibility of the user of this standard to establish appro-
sponge for 2 h. The exposed panel is blotted dry, reweighed,
priate safety and health practices and determine the applica-
recalipered, and inspected for edge cracking. Percentage
bility of regulatory limitations prior to use.
weight and thickness changes are calculated and recorded.
1.4 This international standard was developed in accor-
Edge cracking is rated in accordance with Test Method D661
dance with internationally recognized principles on standard-
and recorded.
ization established in the Decision on Principles for the
Development of International Standards, Guides and Recom-
5. Significance and Use
mendations issued by the World Trade Organization Technical
5.1 This test method provides a measure of the dimensional
Barriers to Trade (TBT) Committee.
stability and integrity of the coated edge of various composite
wood products under accelerated moisture stress. It is widely
2. Referenced Documents
usedasanindicatororpredictoroftheanticipatedperformance
2
2.1 ASTM Standards:
of composite wood products during exterior exposure. It may
D661 Test Method for Evaluating Degree of Cracking of
beusedfordevelopmentalevaluationofcoatings,substrates,or
Exterior Paints
both. It may also be useful for quality control or monitoring of
E177 Practice for Use of the Terms Precision and Bias in
the production of coated or uncoated composite wood prod-
ASTM Test Methods
ucts.
E691 Practice for Conducting an Interlaboratory Study to
Determine the Precision of a Test Method
6. Apparatus
6.1 Wide Flat Tray or Pan, suitable to contain the required
3. Terminology
number of sponges and test boards. The sides must be high
3.1 Definitions of Terms Specific to This Standard:
1
enough to safely contain at least 6 mm ( ⁄4 in.) of solution.
6.2 Rack or Holder, suitable to support the required number
1
This test method is under the jurisdiction of ASTM Committee D01 on Paint of test boards at the nominal 60° angle.
and Related Coatings, Materials, andApplications and is the direct responsibility of
6.3 Micrometer or Vernier Caliper, of sufficient capacity for
Subcommittee D01.52 on Factory Coated Wood Products.
Current edition approved July 1, 2017. Published July 2017. Originally approved the board thickness to be measured and capable of 0.1 mm
in 1991. Last previous edition approved in 2011 as D2065 – 03 (2011). DOI:
accuracy.
10.1520/D2065-03R17.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or 6.4 Balance, with sufficient capacity (typically 400 g) and
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
0.01 g accuracy.
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. 6.5 Suitable Saw, for cutting of samples.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D2065 − 03 (2017)
FIG. 1 Test Apparatus Side View
6.6 Common Household Cellulose Sponges, cut to suitable
size.
7. Materi
...
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D2065 − 03 (Reapproved 2017)
Standard Test Method for
Determination of Edge Performance of Composite Wood
1
Products Under Surfactant Accelerated Moisture Stress
This standard is issued under the fixed designation D2065; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 3.1.1 crack rating, n—a numerical value on a scale from 1
to 10, with 10 representing no evidence of cracking of the edge
1.1 This test method is intended to serve as a means for
(see Test Method D661).
measurement of swelling and cracking of the coated or
3.1.2 composite wood products, n—boards or other struc-
uncoated edge of a composite wood substrate that has been
tural or decorative materials manufactured from wood fibers,
subjected to wetting by a test solution containing surface active
flakes or strands and various resin binders consolidated under
agent.
heat, or pressure, or both.
1.2 The values stated in SI units are to be regarded as the
standard. The values given in parentheses are for information
4. Summary of Test Method
only.
4.1 A surfactant solution is placed in a tray that contains a
1.3 This standard does not purport to address all of the
sponge. A preweighed and calipered panel with a coated edge
safety concerns, if any, associated with its use. It is the
is placed with the edge in contact with the surfactant saturated
responsibility of the user of this standard to establish appro-
sponge for 2 h. The exposed panel is blotted dry, reweighed,
priate safety and health practices and determine the applica-
recalipered, and inspected for edge cracking. Percentage
bility of regulatory limitations prior to use.
weight and thickness changes are calculated and recorded.
1.4 This international standard was developed in accor-
Edge cracking is rated in accordance with Test Method D661
dance with internationally recognized principles on standard-
and recorded.
ization established in the Decision on Principles for the
Development of International Standards, Guides and Recom-
5. Significance and Use
mendations issued by the World Trade Organization Technical
5.1 This test method provides a measure of the dimensional
Barriers to Trade (TBT) Committee.
stability and integrity of the coated edge of various composite
wood products under accelerated moisture stress. It is widely
2. Referenced Documents
used as an indicator or predictor of the anticipated performance
2
2.1 ASTM Standards:
of composite wood products during exterior exposure. It may
D661 Test Method for Evaluating Degree of Cracking of
be used for developmental evaluation of coatings, substrates, or
Exterior Paints
both. It may also be useful for quality control or monitoring of
E177 Practice for Use of the Terms Precision and Bias in
the production of coated or uncoated composite wood prod-
ASTM Test Methods
ucts.
E691 Practice for Conducting an Interlaboratory Study to
Determine the Precision of a Test Method
6. Apparatus
6.1 Wide Flat Tray or Pan, suitable to contain the required
3. Terminology
number of sponges and test boards. The sides must be high
3.1 Definitions of Terms Specific to This Standard:
1
enough to safely contain at least 6 mm ( ⁄4 in.) of solution.
6.2 Rack or Holder, suitable to support the required number
1
This test method is under the jurisdiction of ASTM Committee D01 on Paint of test boards at the nominal 60° angle.
and Related Coatings, Materials, and Applications and is the direct responsibility of
6.3 Micrometer or Vernier Caliper, of sufficient capacity for
Subcommittee D01.52 on Factory Coated Wood Products.
Current edition approved July 1, 2017. Published July 2017. Originally approved the board thickness to be measured and capable of 0.1 mm
in 1991. Last previous edition approved in 2011 as D2065 – 03 (2011). DOI:
accuracy.
10.1520/D2065-03R17.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or 6.4 Balance, with sufficient capacity (typically 400 g) and
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
0.01 g accuracy.
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. 6.5 Suitable Saw, for cutting of samples.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D2065 − 03 (2017)
FIG. 1 Test Apparatus Side View
6.6 Common Household Cellulose Sponges, cut to suitable
size.
7. Materials
7.1 A sufficient supply of test solution.
7.2 Appropriately identified test boards cut to proper size.
8. Hazards
8.1 Wh
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D2065 − 03 (Reapproved 2011) D2065 − 03 (Reapproved 2017)
Standard Test Method for
Determination of Edge Performance of Composite Wood
1
Products Under Surfactant Accelerated Moisture Stress
This standard is issued under the fixed designation D2065; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This test method is intended to serve as a means for measurement of swelling and cracking of the coated or uncoated edge
of a composite wood substrate that has been subjected to wetting by a test solution containing surface active agent.
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D661 Test Method for Evaluating Degree of Cracking of Exterior Paints
E177 Practice for Use of the Terms Precision and Bias in ASTM Test Methods
E691 Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
3. Terminology
3.1 Definitions of Terms Specific to This Standard:
3.1.1 crack rating, n—a numerical value on a scale from 1 to 10, with 10 representing no evidence of cracking of the edge (see
Test Method D661).
3.1.2 composite wood products, n—boards or other structural or decorative materials manufactured from wood fibers, flakes or
strands and various resin binders consolidated under heat, or pressure, or both.
4. Summary of Test Method
4.1 A surfactant solution is placed in a tray that contains a sponge. A preweighed and calipered panel with a coated edge is
placed with the edge in contact with the surfactant saturated sponge for 2 h. The exposed panel is blotted dry, reweighed,
recalipered, and inspected for edge cracking. Percentage weight and thickness changes are calculated and recorded. Edge cracking
is rated in accordance with Test Method D661 and recorded.
5. Significance and Use
5.1 This test method provides a measure of the dimensional stability and integrity of the coated edge of various composite wood
products under accelerated moisture stress. It is widely used as an indicator or predictor of the anticipated performance of
composite wood products during exterior exposure. It may be used for developmental evaluation of coatings, substrates, or both.
It may also be useful for quality control or monitoring of the production of coated or uncoated composite wood products.
1
This test method is under the jurisdiction of ASTM Committee D01 on Paint and Related Coatings, Materials, and Applications and is the direct responsibility of
Subcommittee D01.52 on Factory Coated Wood Products.
Current edition approved Nov. 1, 2011July 1, 2017. Published November 2011July 2017. Originally approved in 1991. Last previous edition approved in 20032011 as
D2065 – 03. 03 (2011). DOI: 10.1520/D2065-03R11.10.1520/D2065-03R17.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D2065 − 03 (2017)
6. Apparatus
6.1 Wide Flat Tray or Pan, suitable to contain the required number of sponges and test boards. The sides must be high enough
1
to safely contain at least 6 mm ( ⁄4 in.) of solution.
6.2 Rack or Holder, suitable to support the required number of test boards at the nominal 60° angle.
6.3 Micrometer or Vernier Caliper, of sufficient capacity for the board thickness to be measured and capable of 0.1 mm
accuracy.
6.4 B
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.