ASTM D3549/D3549M-17
(Test Method)Standard Test Method for Thickness or Height of Compacted Asphalt Mixture Specimens
Standard Test Method for Thickness or Height of Compacted Asphalt Mixture Specimens
SIGNIFICANCE AND USE
4.1 The thickness of a compacted asphalt mixture is often used as a construction check to ensure that the proper quantity of materials has been placed on a project, and to correct strength measurement on constant diameter specimens with varying heights.
Note 1: The text of this test method references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the test method.
Note 2: The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Specification D3666 are generally considered capable of competent and objective testing, sampling, inspection, etc. Users of this standard are cautioned that compliance with Specification D3666 alone does not completely ensure reliable results. Reliable results depend on many factors; following the suggestions of Specification D3666 or some similar acceptable guideline provides a means of evaluating and controlling some of those factors.
SCOPE
1.1 This test method covers determination of the thickness (or height) of compacted asphalt mixture specimens.
1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.
1.2.1 Section 7.4 specifies SI units because they are the units used in the equations for Test Methods D1188 and D2726. Performing calculations without first converting any measurements made in inch-pound units to SI units in 7.4 will result in nonconformance with the standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D3549/D3549M − 17
Standard Test Method for
Thickness or Height of Compacted Asphalt Mixture
1
Specimens
This standard is issued under the fixed designation D3549/D3549M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope D2726 Test Method for Bulk Specific Gravity and Density
of Non-Absorptive Compacted Asphalt Mixtures
1.1 This test method covers determination of the thickness
D3666 Specification for Minimum Requirements for Agen-
(or height) of compacted asphalt mixture specimens.
cies Testing and Inspecting Road and Paving Materials
1.2 Units—The values stated in either SI units or inch-
D5361/D5361M Practice for Sampling Compacted Asphalt
pound units are to be regarded separately as standard. The
Mixtures for Laboratory Testing
values stated in each system may not be exact equivalents;
therefore,eachsystemshallbeusedindependentlyoftheother.
3. Terminology
Combining values from the two systems may result in noncon-
3.1 Definitions—For definitions of terms used in this
formance with the standard.
standard, refer to Terminology D8.
1.2.1 Section 7.4 specifies SI units because they are the
units used in the equations for Test Methods D1188 and
4. Significance and Use
D2726. Performing calculations without first converting any
measurements made in inch-pound units to SI units in 7.4 will
4.1 The thickness of a compacted asphalt mixture is often
result in nonconformance with the standard.
used as a construction check to ensure that the proper quantity
1.3 This standard does not purport to address all of the of materials has been placed on a project, and to correct
safety concerns, if any, associated with its use. It is the
strength measurement on constant diameter specimens with
responsibility of the user of this standard to establish appro- varying heights.
priate safety, health, and environmental practices and deter-
NOTE 1—The text of this test method references notes and footnotes
mine the applicability of regulatory limitations prior to use.
which provide explanatory material.These notes and footnotes (excluding
1.4 This international standard was developed in accor-
those in tables and figures) shall not be considered as requirements of the
dance with internationally recognized principles on standard-
test method.
ization established in the Decision on Principles for the
NOTE 2—The quality of the results produced by this standard are
dependent on the competence of the personnel performing the procedure
Development of International Standards, Guides and Recom-
and the capability, calibration, and maintenance of the equipment used.
mendations issued by the World Trade Organization Technical
Agencies that meet the criteria of Specification D3666 are generally
Barriers to Trade (TBT) Committee.
considered capable of competent and objective testing, sampling,
inspection, etc. Users of this standard are cautioned that compliance with
2. Referenced Documents
Specification D3666 alone does not completely ensure reliable results.
2 Reliable results depend on many factors; following the suggestions of
2.1 ASTM Standards:
Specification D3666 or some similar acceptable guideline provides a
D8 Terminology Relating to Materials for Roads and Pave-
means of evaluating and controlling some of those factors.
ments
D1188 TestMethodforBulkSpecificGravityandDensityof
5. Apparatus
Compacted Bituminous Mixtures Using Coated Samples
5.1 Any of the following apparatus may be used to measure
1
thedimensionsoftestspecimenstothenearest0.1cm( ⁄16in.):
1
This test method is under the jurisdiction of ASTM Committee D04 on Road
NOTE 3—The specifying agency may establish alternate unit require-
and Paving Materials and is the direct responsibility of Subcommittee D04.21 on
ments for measurement.
Specific Gravity and Density of Asphalt Mixtures.
Current edition approved Oct. 1, 2017. Published October 2017. Originally
5.1.1 A metal tape or rule.
approved in 1977. Last previous edition approved in 2011 as D3549/D3549M – 11.
DOI: 10.1520/D3549_D3459M-17. 5.1.2 A set of calipers.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
5.1.3 A measurement jig or other device, fabricated in such
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
a manner that it is capable of measuring specimen thicknesses
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. in accordance with this procedure.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D3549/D3549M − 11 D3549/D3549M − 17
Standard Test Method for
Thickness or Height of Compacted Bituminous Paving
1
Asphalt Mixture Specimens
This standard is issued under the fixed designation D3549/D3549M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This test method covers determination of the thickness (or height) of compacted bituminous paving asphalt mixture
specimens.
1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated
in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values
from the two systems may result in non-conformancenonconformance with the standard.
1.2.1 Section 6.47.4 specifies SI units because they are the units used in the equations for ASTM D 1188Test Methods D1188
and D2726D 2726. . Performing calculations without first converting any measurements made in inch-pound units to SI units in
Section7.4 6.4 will result in non-conformancenonconformance with the standard.
1.3 This standard does not purport to address all of the safety problems,concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appropriate safety safety, health, and healthenvironmental practices and
determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D8 Terminology Relating to Materials for Roads and Pavements
D1188 Test Method for Bulk Specific Gravity and Density of Compacted Bituminous Mixtures Using Coated Samples
D2726 Test Method for Bulk Specific Gravity and Density of Non-Absorptive Compacted Asphalt Mixtures
D3666 Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
D5361/D5361M Practice for Sampling Compacted Asphalt Mixtures for Laboratory Testing
3. Terminology
3.1 Definitions—For definitions of terms used in this standard, refer to Terminology D8.
4. Significance and Use
4.1 The thickness of a compacted bituminous paving asphalt mixture is often used as a construction check to ensure that the
proper quantity of materials has been placed on a project, and to correct strength measurement on constant diameter specimens
with varying heights.
NOTE 1—The text of this test method references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those
in tables and figures) shall not be considered as requirements of the test method.
NOTE 2—The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the
capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Standard Practice Specification D3666 are generally
considered capable of competent and objective testing/sampling/inspection/etc. testing, sampling, inspection, etc. Users of this standard are cautioned that
compliance with PracticeSpecification D3666 alone does not completely assureensure reliable results. Reliable results depend on many factors; following
1
This test method is under the jurisdiction of ASTM Committee D04 on Road and Paving Materials and is the direct responsibility of Subcommittee D04.21 on Specific
Gravity and Density of Asphalt Mixtures.
Current edition approved Dec. 1, 2011Oct. 1, 2017. Published December 2011October 2017. Originally approved in 1977. Last previous edition approved in 20032011
as D3549 – 93aD3549/D3549M – 11. 03. DOI: 10.1520/D3549_D3459M-11.10.1520/D3549_D3459M-17.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ---
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.