ASTM E1977-04
(Specification)Standard Specification for Shelter, Tactical, Expandable, One-Side
Standard Specification for Shelter, Tactical, Expandable, One-Side
SCOPE
1.1 This specification covers a rigid wall, one-side expandable shelter constructed of aluminum-faced, nonmetallic honeycomb sandwich panels, and meeting the International Organization for Standardization (ISO) Cargo Container specification in the transport mode. Nominal dimensions when closed (container mode) are: height 8 ft, width 8 ft and length 20 ft (2.4 by 2.4 by 6.1 m). Approximate dimensions, when expanded (shelter mode) are: height 8 ft, width 15 ft and length 20 ft (2.4 by 4.6 by 6.1 m).
1.2 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only.
1.3 The following precautionary statement pertains to the test method portion only, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
An American National Standard
Designation: E 1977 – 04
Standard Specification for
1
Shelter, Tactical, Expandable, One-Side
This standard is issued under the fixed designation E 1977; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope E 1091 Specification for Nonmetallic Honeycomb Core for
Use in Shelter Panels
1.1 This specification covers a rigid wall, one-side expand-
E 1749 Terminology Relating to Rigid Wall Relocatable
able shelter constructed of aluminum-faced, nonmetallic hon-
Shelters
eycomb sandwich panels, and meeting the International Orga-
E 1773 Practice for Sealing Rigid Wall Tactical Shelters
nization for Standardization (ISO) Cargo Container
with Polysulfide Based Sealants
specification in the transport mode. Nominal dimensions when
E 1826 Specification for Low Volatile Organic Compound
closed (container mode) are: height 8 ft, width 8 ft and length
(VOC) Corrosion-Inhibiting Adhesive Primer for Alumi-
20 ft. (2.4 by 2.4 by 6.1 m) Approximate dimensions, when
num Alloys to Be Adhesively Bonded
expanded(sheltermode)are:height8ft,width15ftandlength
E 1925 Specification for Engineering and Design Criteria
20 ft (2.4 by 4.6 by 6.1 m).
for Rigid Wall Relocatable Structures
1.2 The values stated in inch-pound units are to be regarded
3
2.2 ISO Standards:
as the standard. The SI units given in parentheses are for
ISO1161-1980 Series1-FreightContainers-CornerFittings,
information only.
Specification
1.3 The following precautionary statement pertains to the
ISO 1496/I Series 1-Freight Containers-Specification and
test method portion only. Section 7, of this specification; This
Testing Part I-General Cargo Containers
standard does not purport to address all of the safety concerns,
ISO 9001 Quality Systems—Model for Quality Assurance
if any, associated with its use. It is the responsibility of the user
in Design, Development, Production, Installation, and
of this standard to establish appropriate safety and health
Servicing
practices and determines the applicability of regulatory limi-
4
2.3 Military Standards:
tations prior to use.
MIL-STD-129 Marking for Shipping and Storage
2. Referenced Documents MIL-STD-810 Environmental Engineering Considerations
2
and Laboratory Tests
2.1 ASTM Standards:
2.4 ANSI/ASQC Standard:
E 864 Practice for Surface Preparation ofAluminumAlloys
ANSI/ASQC 21.4-1993 Sampling Procedures and Tables
to be Adhesively Bonded in Honeycomb Shelter Panels
5
for Inspection by Attributes
E 865 Specification for Structural Film Adhesives for Hon-
6
2.5 Drawings:
eycomb Sandwich Panels
5-4-2828 Shelter, Assembly, One-Side Expandable-60 amp
E 866 Specification for Corrosion-Inhibiting Adhesive
5-4-3200 Shelter, Assembly, One-Side Expandable-100
Primer for Aluminum Alloys to be Adhesively Bonded in
6
amp
Honeycomb Shelter Panels
7
2.6 SAE Standards
E 874 Practice forAdhesive Bonding ofAluminum Facings
SAE-AMS-STD-1595 Qualification of Aircraft, Missile,
to Nonmetallic Honeycomb Core for Shelter Panels
and Aerospace Fusion Welding
E 990 Specification for Core-Splice Adhesive for Honey-
comb Sandwich Shelter Panels
3
Available fromAmerican National Standards Institute (ANSI), 25 W. 43rd St.,
1
This specification is under the jurisdiction of ASTM Committee E06 on 4th Floor, New York, NY 10036.
4
Performance of Buildings and is the direct responsibility of Subcommittee E06.53 Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,
on Materials and Processes for Durable Rigidwall Relocatable Structures. Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098
5
Current edition approved April 1, 2004. Published April 2004. Originally Available from American Society for Quality (ASQ), 600 N. Plankinton Ave.,
e1
approved in 1998. Last previous edition approved in 2001 as E 1977 – 01 . Milwaukee, WI 53203.
2 6
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Copies of drawings are available from USArmy Natick Soldier Center,ATTN:
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM AMSRD-NSC-CP-CS, Kansas Street, Natick, MA 01760-5018.
7
Standards volume information, refer to the standard’s Document Summary page on Available from Society of Automotive Engineers (SAE), 400 Commonwealth
the ASTM website. Dr., Warrendale, PA 15096-0001.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
E1977–04
SAE-AMS-STD-2219 Fusion Welding for Aerospac
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.