iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM F1792-97(2010)

(Specification)

Standard Specification for Special Requirements for Valves Used in Gaseous Oxygen Service

Standard Specification for Special Requirements for Valves Used in Gaseous Oxygen Service

ABSTRACT
This specification covers the special requirements for valves used in gaseous oxygen service. The pressure containing/retaining envelope, bellows, and end nipples, shall be made of nickel-copper alloy. Internal trim which is in contact with the line media shall either be made of nickel-copper alloy, bronze, nickel-aluminum-bronze, Inconel alloy 600, brass or other materials which are compatible with oxygen service. Non-metallic seat, seat insert, or seals shall be manufacture from either TFE, reinforced TFE, CTFE, plastic, polyamide, or PEEK. Materials for lubricants shall be halocarbon, Dupont, Barycote 601, or other lubricants compatible with oxygen service. Valves shall be constructed to minimize the possibility of initiating ignition in gaseous oxygen service. Valves shall be constructed to minimize oxygen escape in the event of an internal or external fire. This shall be accomplished by pressure-boundary sealing, internal seating and pressure surge. The manual valves shall be of the packless design, with the stem sealed by a bellows.
SCOPE
1.1 This specification covers the special requirements for valves used in gaseous oxygen service. It is intended that this specification be invoked as an additional requirement in conjunction with primary valve specifications.
1.2 The values stated in this specification in inch-pound units are to be regarded as the standard. The SI equivalent shown in parenthesis are provided for information only.

General Information

Status
Historical
Publication Date
30-Apr-2010
ICS
23.060.01 - Valves in general
Technical Committee
F25 - Ships and Marine Technology
Drafting Committee
F25.11 - Machinery and Piping Systems
Current Stage
Ref Project

Relations

Replaces
ASTM F1792-97(2004) - Standard Specification for Special Requirements for Valves Used in Gaseous Oxygen Service
Effective Date
01-May-2010

Buy Standard

ASTM F1792-97(2010) - Standard Specification for Special Requirements for Valves Used in Gaseous Oxygen ServiceASTM F1792-97(2010) - Standard Specification for Special Requirements for Valves Used in Gaseous Oxygen Service
PreviousNext
Technical specification
ASTM F1792-97(2010) - Standard Specification for Special Requirements for Valves Used in Gaseous Oxygen Service
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F1792 −97(Reapproved 2010) An American National Standard
Standard Specification for
Special Requirements for Valves Used in Gaseous Oxygen
1
Service
This standard is issued under the fixed designation F1792; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope MIL-STD-278 Fabrication,Welding and Inspection; Casting
Inspection and Repair for Machinery, Piping and Process
1.1 This specification covers the special requirements for
Vessels in Ships of the United States Navy
valves used in gaseous oxygen service. It is intended that this
MIL-STD-271 Non-destructive Testing Requirements for
specification be invoked as an additional requirement in
Metals
conjunction with primary valve specifications.
MIL-P-46122 Plastic Molding and Extrusion Material, Poly-
1.2 The values stated in this specification in inch-pound
vinylidene Fluoride Polymer and Copolymer
units are to be regarded as the standard. The SI equivalent
shown in parenthesis are provided for information only.
3. Ordering Information
3.1 Ordering documentation for valves under this specifica-
2. Referenced Documents
tion shall include the following information, as required, to
2
2.1 ASTM Standards:
describe the equipment adequately.
G63 Guide for Evaluating Nonmetallic Materials for Oxy-
3.1.1 ASTM designation and year of issue.
gen Service
3.1.2 Primary valve specification (see 1.1).
G88 Guide for Designing Systems for Oxygen Service
3.1.3 End preparations, if different than specified in 4.4.
G93 Practice for Cleaning Methods and Cleanliness Levels
3.1.4 Supplementary requirements, if any (see S1 through
for Material and Equipment Used in Oxygen-Enriched
S4).
Environments
G94 Guide for Evaluating Metals for Oxygen Service
4. Valve Design and Construction
3
2.2 American National Standards Institute (ANSI):
4.1 Valvesshallincorporatethefeaturesspecifiedin4.2-4.6.
ANSI B1.1 Unified Screw Threads
4
2.3 American Society of Mechanical Engineers (ASME):
4.2 Materials of Construction—Material requirements shall
ASME Boiler and Pressure Vessel Code
be as follows:
5
2.4 Military Standards and Specifications: 4.2.1 The pressure containing/retaining envelope (including
MIL-STD-1330 Standard Practice for Precision Cleaning
any bolting, union nuts, or other fastening devices establishing
and Testing of Shipboard Oxygen, Helium, Helium-
the integrity of the pressure containing/retaining envelope),
Oxygen, Nitrogen, and Hydrogen Systems
bellows (where applicable), and end nipples, shall be nickel-
MIL-V-5027 Valves, Check, Oxygen, High Pressure
copper (70-30). Internal trim which is in contact with the line
media shall be nickel-copper (70-30), bronze, nickel-
aluminum-bronze, InconelAlloy 600, brass, or other materials
1
This specification is under the jurisdiction of ASTM Committee F25 on Ships
which are compatible with oxygen service.
and Marine Technology and is the direct responsibility of Subcommittee F25.11 on
Machinery and Piping Systems. 4.2.2 Non-metallicseat,seatinsert,orseals.Thesematerials
Current edition approved May 1, 2010. Published June 2010. Originally
shall be selected from TFE, Reinforced TFE, CTFE, plastic in
approved in 1997. Last previous edition approved in 2004 as F1792 - 97 (2004).
accordance with MIL-P-46122, Polyamide (Vespel), or PEEK.
DOI: 10.1520/F1792-97R10.
2 The materials for O-rings and gaskets shall be compatible for
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
oxygen service.
Standards volume information, refer to the standard’s Document Summary page on
4.2.3 Lubricants—Materials for lubricants shall be halocar-
the ASTM website.
bon (25-5S), Dupont (Krytox 240AC, 240AZ), Braycote 601,
3
Available fromAmerican National Standards Institute (ANSI), 25 W. 43rd St.,
or other lubricants compatible with oxygen service.
4th Floor, New York, NY 10036, http://www.ansi.org.
4
Available from American Society of Mechanical Engineers (ASME), ASME
4.2.4 Guidance on the selection of materials for oxygen
International Headquarters, Three Park Ave., New York, NY 10016-5990, http://
service can be found in Guides G63 and G94. Guidance on
www.asme.org.
5
designing systems for oxygen service can be found in Guide
AvailablefromStandardizationDocumentsOrderDesk,Bldg.4SectionD,700
Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS. G88.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F1792−97 (2010)
4.3 General R
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM F1387-23(Specification)
Standard Specification for Performance of Piping and Tubing Mechanically Attached Fittings

ABSTRACT
This specification establishes the performance characteristics required for mechanically attached fittings (MAFs) for use in piping and tubing systems. These fittings directly attach to pipe or tube by mechanical deformation of the pipe or tube or fitting, or a combination thereof, creating a seal and a restrained joint. process. MAFs covered here are classified into the following design types: Type I—radially swaged MAF (permanent); Type II—flared MAF (separable); Type III—flareless (bite-type) MAF (separable); Type IV—grip-type MAF (separable); Type V—shape memory alloy (SMA) MAF (permanent); and Type VI—axially swaged MAF (permanent). Moreover, the MAFs shall be made from on or more of the following material grade: Grade A—carbon steel; Grade B—stainless steel; Grade C—nickel-copper; Grade D—copper-nickel; Grade E—brass; and Grade F—nickel titanium. The MAFs shall also be grouped into ten classes according to their pressure ratings. The standard qualification tests to which the MAFs shall perform satisfactorily are pneumatic proof test, hydrostatic proof test, impulse test, flexure fatigue test, tensile test, hydrostatic burst test, repeated assembly test, rotary flexure test, and mercurous nitrate test. Successful completion of the tests described constitutes completion of the technical portion of the qualification
SCOPE
1.1 This specification establishes the performance characteristics required for mechanically attached fittings (MAFs) for use in piping and tubing systems. These fittings directly attach to pipe or tube by mechanical deformation of the pipe or tube or fitting, or a combination thereof, creating a seal and a restrained joint. The seal may be created via the mechanical deformation or created independently. Successful completion of the tests described constitutes completion of the technical portion of the qualification process.  
1.2 Supplementary requirements are provided for use when additional testing or inspection is desired. These shall apply only when specified in part or whole by the purchaser in the order. Unless otherwise specified, U.S. Navy contracts shall invoke the supplementary requirements in whole.  
1.3 Unless specific MAF types are specified, the term “MAF” shall apply to all types described herein.  
1.4 The tests specified in Section 13 and described in Annex A1 and the Supplementary Requirements Section are applicable only to ascertain the performance characteristics of MAFs. These tests are not intended for use in the evaluation of non-MAF products.  
1.5 A fire performance test is specified in Supplementary Requirement S7. This test provides general guidelines to determine the responsiveness of MAFs when subjected to fire. This test should not be considered for use to evaluate non-MAF products.  
1.6 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.7 The following safety hazards caveat applies only to the tests listed in Section 13 and the tests described in the Supplementary Requirements Section and the annexes of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    31 pages
    English language
    sale 15% off
  • Technical specification
    31 pages
    English language
    sale 15% off
ASTM
ASTM F1792-97(2021)(Specification)
Standard Specification for Special Requirements for Valves Used in Gaseous Oxygen Service

ABSTRACT
This specification covers the special requirements for valves used in gaseous oxygen service. The pressure containing/retaining envelope, bellows, and end nipples, shall be made of nickel-copper alloy. Internal trim which is in contact with the line media shall either be made of nickel-copper alloy, bronze, nickel-aluminum-bronze, Inconel alloy 600, brass or other materials which are compatible with oxygen service. Non-metallic seat, seat insert, or seals shall be manufacture from either TFE, reinforced TFE, CTFE, plastic, polyamide, or PEEK. Materials for lubricants shall be halocarbon, Dupont, Barycote 601, or other lubricants compatible with oxygen service. Valves shall be constructed to minimize the possibility of initiating ignition in gaseous oxygen service. Valves shall be constructed to minimize oxygen escape in the event of an internal or external fire. This shall be accomplished by pressure-boundary sealing, internal seating and pressure surge. The manual valves shall be of the packless design, with the stem sealed by a bellows.
SCOPE
1.1 This specification covers the special requirements for valves used in gaseous oxygen service. It is intended that this specification be invoked as an additional requirement in conjunction with primary valve specifications.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM F1793-97(2021)(Specification)
Standard Specification for Automatic Shut-Off Valves (Also Known as Excess Flow Valves, EFV) for Air or Nitrogen Service

ABSTRACT
This specification covers self-contained automatic shutoff valves (also known as excess flow valves) for air or nitrogen service. They are intended to be installed as safety devices to quickly and automatically shut off flow under certain excess flow conditions caused by a downstream failure or casualty, such as a hose rupture. Automatic shut-off valves shall be of the following types, styles, sizes, pressure ratings, and end connections: Types I and II; Styles 1 and 2. Each automatic shut-off valve must pass the following tests: visual examination; hydrostatic shell test; seal tightness test; external leakage test; and set-point test.
SCOPE
1.1 This specification covers self-contained automatic shut-off valves (also known as excess flow valves) for air or nitrogen service. They are intended to be installed as safety devices to quickly and automatically shut off flow under certain excess flow conditions caused by a downstream failure or casualty, such as a hose rupture.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off
ASTM
ASTM F1387-23(Specification)
Standard Specification for Performance of Piping and Tubing Mechanically Attached Fittings

ABSTRACT
This specification establishes the performance characteristics required for mechanically attached fittings (MAFs) for use in piping and tubing systems. These fittings directly attach to pipe or tube by mechanical deformation of the pipe or tube or fitting, or a combination thereof, creating a seal and a restrained joint. process. MAFs covered here are classified into the following design types: Type I—radially swaged MAF (permanent); Type II—flared MAF (separable); Type III—flareless (bite-type) MAF (separable); Type IV—grip-type MAF (separable); Type V—shape memory alloy (SMA) MAF (permanent); and Type VI—axially swaged MAF (permanent). Moreover, the MAFs shall be made from on or more of the following material grade: Grade A—carbon steel; Grade B—stainless steel; Grade C—nickel-copper; Grade D—copper-nickel; Grade E—brass; and Grade F—nickel titanium. The MAFs shall also be grouped into ten classes according to their pressure ratings. The standard qualification tests to which the MAFs shall perform satisfactorily are pneumatic proof test, hydrostatic proof test, impulse test, flexure fatigue test, tensile test, hydrostatic burst test, repeated assembly test, rotary flexure test, and mercurous nitrate test. Successful completion of the tests described constitutes completion of the technical portion of the qualification
SCOPE
1.1 This specification establishes the performance characteristics required for mechanically attached fittings (MAFs) for use in piping and tubing systems. These fittings directly attach to pipe or tube by mechanical deformation of the pipe or tube or fitting, or a combination thereof, creating a seal and a restrained joint. The seal may be created via the mechanical deformation or created independently. Successful completion of the tests described constitutes completion of the technical portion of the qualification process.  
1.2 Supplementary requirements are provided for use when additional testing or inspection is desired. These shall apply only when specified in part or whole by the purchaser in the order. Unless otherwise specified, U.S. Navy contracts shall invoke the supplementary requirements in whole.  
1.3 Unless specific MAF types are specified, the term “MAF” shall apply to all types described herein.  
1.4 The tests specified in Section 13 and described in Annex A1 and the Supplementary Requirements Section are applicable only to ascertain the performance characteristics of MAFs. These tests are not intended for use in the evaluation of non-MAF products.  
1.5 A fire performance test is specified in Supplementary Requirement S7. This test provides general guidelines to determine the responsiveness of MAFs when subjected to fire. This test should not be considered for use to evaluate non-MAF products.  
1.6 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.7 The following safety hazards caveat applies only to the tests listed in Section 13 and the tests described in the Supplementary Requirements Section and the annexes of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    31 pages
    English language
    sale 15% off
  • Technical specification
    31 pages
    English language
    sale 15% off
ASTM
ASTM F1792-97(2021)(Specification)
Standard Specification for Special Requirements for Valves Used in Gaseous Oxygen Service

ABSTRACT
This specification covers the special requirements for valves used in gaseous oxygen service. The pressure containing/retaining envelope, bellows, and end nipples, shall be made of nickel-copper alloy. Internal trim which is in contact with the line media shall either be made of nickel-copper alloy, bronze, nickel-aluminum-bronze, Inconel alloy 600, brass or other materials which are compatible with oxygen service. Non-metallic seat, seat insert, or seals shall be manufacture from either TFE, reinforced TFE, CTFE, plastic, polyamide, or PEEK. Materials for lubricants shall be halocarbon, Dupont, Barycote 601, or other lubricants compatible with oxygen service. Valves shall be constructed to minimize the possibility of initiating ignition in gaseous oxygen service. Valves shall be constructed to minimize oxygen escape in the event of an internal or external fire. This shall be accomplished by pressure-boundary sealing, internal seating and pressure surge. The manual valves shall be of the packless design, with the stem sealed by a bellows.
SCOPE
1.1 This specification covers the special requirements for valves used in gaseous oxygen service. It is intended that this specification be invoked as an additional requirement in conjunction with primary valve specifications.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM F1793-97(2021)(Specification)
Standard Specification for Automatic Shut-Off Valves (Also Known as Excess Flow Valves, EFV) for Air or Nitrogen Service

ABSTRACT
This specification covers self-contained automatic shutoff valves (also known as excess flow valves) for air or nitrogen service. They are intended to be installed as safety devices to quickly and automatically shut off flow under certain excess flow conditions caused by a downstream failure or casualty, such as a hose rupture. Automatic shut-off valves shall be of the following types, styles, sizes, pressure ratings, and end connections: Types I and II; Styles 1 and 2. Each automatic shut-off valve must pass the following tests: visual examination; hydrostatic shell test; seal tightness test; external leakage test; and set-point test.
SCOPE
1.1 This specification covers self-contained automatic shut-off valves (also known as excess flow valves) for air or nitrogen service. They are intended to be installed as safety devices to quickly and automatically shut off flow under certain excess flow conditions caused by a downstream failure or casualty, such as a hose rupture.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off
ASTM
ASTM A592/A592M-10(2020)(Specification)
Standard Specification for High-Strength Quenched and Tempered Low-Alloy Steel Forged Parts for Pressure Vessels

ABSTRACT
ASTM A592/A592M-04 covers the standard specification for high-strength quenched and tempered low-alloy steel forged fittings and parts used for pressure vessels. The steel shall be made by a melting process and shall be fully killed and fine grained. After forging and before reheating, the forgings shall be cooled to provide substantially complete transformation of austenite. Samples for mechanical test specimens shall be removed after the quenching and tempering heat treatment. The test specimens may be machined from a production forging or from special forged blocks suitably worked and heat treated with the production forgings. Such special blocks shall be obtained from an ingot, slab, or billet from the same heat as the forgings they represent and shall be reduced by forging in a manner similar to that for the products to be represented. The specimens shall undergo tension and Charpy V-notch impact tests.
SCOPE
1.1 This specification2 covers high-strength quenched and tempered low-alloy steel forged parts for pressure vessels. The maximum thickness of forgings under this specification shall be 11/2 in. [38 mm] for Grade A, and 4 in. [100 mm] for Grades E and F.
Note 1: These grades are similar to corresponding grades in Specification A517/A517M.  
1.2 Although no provision is made for supplementary requirements in this standard, the supplementary requirements in Specification A788/A788M may be considered by the purchaser.  
1.3 Welding technique is of fundamental importance and it is presupposed that welding procedures will be in accordance with approved methods for the class of material used.  
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.5 Unless the order specifies the applicable “M” specification designation, the material shall be furnished to the inch-pound units.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM B637-23(Specification)
Standard Specification for Precipitation-Hardening and Cold Worked Nickel Alloy Bars, Forgings, and Forging Stock for Moderate or High Temperature Service

ABSTRACT
This specification covers hot- and cold-worked precipitation-hardenable nickel alloy rod, bar, forgings, and forging stock for high-temperature service. Chemical analysis shall be performed on the alloy and shall conform to the chemical composition requirement in carbon, manganese, silicon, phosphorus, sulfur, chromium, cobalt, molybdenum, columbium, tantalum, titanium, aluminum, zirconium, boron, iron, copper, and nickel. The material shall follow recommended annealing treatment, solution treatment, stabilizing treatment, and precipitation hardening treatment. Tension testing, hardness testing and stress-rupture testing shall be performed on the material and shall comply to the required tensile strength, yield strength, elongation, reduction in area, and Brinell hardness.
SCOPE
1.1 This specification2 covers hot- and cold-worked precipitation-hardenable nickel alloy rod, bar, forgings, and forging stock for moderate or high temperature service (Table 1).  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off
  • Technical specification
    7 pages
    English language
    sale 15% off
ASTM
ASTM C596-23(Test Method)
Standard Test Method for Drying Shrinkage of Mortar Containing Hydraulic Cement

SIGNIFICANCE AND USE
4.1 This test method establishes a selected set of conditions of temperature, relative humidity and rate of evaporation of the environment to which a mortar specimen of stated composition shall be subjected for a specified period of time during which its change in length is determined and designated “drying shrinkage.”  
4.2 The drying shrinkage of mortar as determined by this test method has a linear relation to the drying shrinkage of concrete made with the same cement and exposed to the same drying conditions.4 Hence this test method may be used when it is desired to develop data on the effect of a hydraulic cement on the drying shrinkage of concrete made with that cement.
SCOPE
1.1 This test method determines the change in length on drying of mortar bars containing hydraulic cement and graded standard sand.  
1.2 The values stated in SI units are to be regarded as standard. When combined standards are referenced, the selection of measurement system is at the user’s discretion subject to the requirements of the referenced standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Warning—Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and tissue upon prolonged exposure).2  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM F3337-23(Guide)
Standard Guide for Taking Property and Behavior Measurements on Weathered Fractions of Oil

SIGNIFICANCE AND USE
5.1 A standard procedure is necessary to establish property changes for spilled oils or petroleum products at different oil weathering stages.  
5.2 This procedure employs standardized equipment, and test procedures.  
5.3 This procedure should be performed at the stages of weathering corresponding to the spill conditions of interest.
SCOPE
1.1 This guide summarizes methods to fractionate oil by evaporative weathering and then measure the properties and behavior of the weathered oil. The results of this guide can provide oil behavior data for input into oil spill models and response method selection.  
1.2 This guide covers general procedures for oil weathering and behavior and does not cover all possible procedures which may be applicable to this topic.  
1.3 The results obtained using this guide are intended to provide baseline data for the behavior of oil and petroleum products when spilled and input to oil spill models.  
1.4 The results obtained using this guide can be used directly to predict certain facets of oil spill behavior or as input to oil spill models.  
1.5 The accuracy of the guide depends very much on the representative nature of the oil sample used. Certain oils can have different properties depending on their chemical contents at the moment a sample is taken.  
1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    4 pages
    English language
    sale 15% off
  • Guide
    4 pages
    English language
    sale 15% off