ASTM C913-21
(Specification)Standard Specification for Precast Concrete Water and Wastewater Structures
Standard Specification for Precast Concrete Water and Wastewater Structures
SCOPE
1.1 This specification covers the recommended design requirements and manufacturing practices for monolithic or sectional precast concrete water and wastewater structures with the exception of concrete pipe, box culverts, utility structures, septic tanks, grease interceptor tanks, and items included under the scope of Specification C478/C478M.
Note 1: Water and wastewater structures are defined as solar heating reservoirs, cisterns, holding tanks, leaching tanks, extended aeration tanks, wet wells, pumping stations, distribution boxes, oil-water separators, treatment plants, manure pits, catch basins, drop inlets, and similar structures.
Note 2: Installation and sealant requirements should receive special consideration due to special features of the application.
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:C913 −21
Standard Specification for
1
Precast Concrete Water and Wastewater Structures
This standard is issued under the fixed designation C913; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope A416/A416M Specification for Low-Relaxation, Seven-
Wire Steel Strand for Prestressed Concrete
1.1 This specification covers the recommended design re-
A421/A421M Specification for Stress-Relieved Steel Wire
quirements and manufacturing practices for monolithic or
for Prestressed Concrete
sectionalprecastconcretewaterandwastewaterstructureswith
A615/A615M SpecificationforDeformedandPlainCarbon-
the exception of concrete pipe, box culverts, utility structures,
Steel Bars for Concrete Reinforcement
septic tanks, grease interceptor tanks, and items included under
A706/A706M Specification for Deformed and Plain Low-
the scope of Specification C478/C478M.
Alloy Steel Bars for Concrete Reinforcement
NOTE 1—Water and wastewater structures are defined as solar heating
A1064/A1064M Specification for Carbon-Steel Wire and
reservoirs,cisterns,holdingtanks,leachingtanks,extendedaerationtanks,
Welded Wire Reinforcement, Plain and Deformed, for
wet wells, pumping stations, distribution boxes, oil-water separators,
Concrete
treatment plants, manure pits, catch basins, drop inlets, and similar
C33/C33M Specification for Concrete Aggregates
structures.
NOTE 2—Installation and sealant requirements should receive special
C39/C39M Test Method for Compressive Strength of Cylin-
consideration due to special features of the application.
drical Concrete Specimens
1.2 The values stated in inch-pound units are to be regarded C94/C94M Specification for Ready-Mixed Concrete
as the standard. The values given in parentheses are for C125 Terminology Relating to Concrete and Concrete Ag-
information only. gregates
C150/C150M Specification for Portland Cement
1.3 This standard does not purport to address all of the
C173/C173M Test Method forAir Content of Freshly Mixed
safety concerns, if any, associated with its use. It is the
Concrete by the Volumetric Method
responsibility of the user of this standard to establish appro-
C231/C231M Test Method forAir Content of Freshly Mixed
priate safety, health, and environmental practices and deter-
Concrete by the Pressure Method
mine the applicability of regulatory limitations prior to use.
C260/C260M Specification for Air-Entraining Admixtures
1.4 This international standard was developed in accor-
for Concrete
dance with internationally recognized principles on standard-
C330/C330M Specification for Lightweight Aggregates for
ization established in the Decision on Principles for the
Structural Concrete
Development of International Standards, Guides and Recom-
C478/C478M Specification for Circular Precast Reinforced
mendations issued by the World Trade Organization Technical
Concrete Manhole Sections
Barriers to Trade (TBT) Committee.
C494/C494M Specification for Chemical Admixtures for
2. Referenced Documents Concrete
2 C595/C595M Specification for Blended Hydraulic Cements
2.1 ASTM Standards:
C618 Specification for Coal Fly Ash and Raw or Calcined
A184/A184M Specification for Welded Deformed Steel Bar
Natural Pozzolan for Use in Concrete
Mats for Concrete Reinforcement
C685/C685M Specification for Concrete Made by Volumet-
ric Batching and Continuous Mixing
1
This specification is under the jurisdiction ofASTM Committee C27 on Precast
C890 Practice for Minimum Structural Design Loading for
ConcreteProductsandisthedirectresponsibilityofSubcommitteeC27.30onWater
Monolithic or Sectional Precast Concrete Water and
and Wastewater Containers.
Wastewater Structures
Current edition approved Aug. 1, 2021. Published August 2021. Originally
C989/C989M Specification for Slag Cement for Use in
approved in 1979. Last previous edition approved in 2018 as C913 – 18. DOI:
10.1520/C0913-21.
Concrete and Mortars
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
C990 Specification for Joints for Concrete Pipe, Manholes,
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
and Precast Box Sections Using Preformed Flexible Joint
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. Sealants
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. Uni
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C913 − 18 C913 − 21
Standard Specification for
1
Precast Concrete Water and Wastewater Structures
This standard is issued under the fixed designation C913; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope
1.1 This specification covers the recommended design requirements and manufacturing practices for monolithic or sectional
precast concrete water and wastewater structures with the exception of concrete pipe, box culverts, utility structures, septic tanks,
grease interceptor tanks, and items included under the scope of Specification C478C478/C478M.
NOTE 1—Water and wastewater structures are defined as solar heating reservoirs, cisterns, holding tanks, leaching tanks, extended aeration tanks, wet
wells, pumping stations, distribution boxes, oil-water separators, treatment plants, manure pits, catch basins, drop inlets, and similar structures.
NOTE 2—Installation and sealant requirements should receive special consideration due to special features of the application.
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information
only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of
regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
A184/A184M Specification for Welded Deformed Steel Bar Mats for Concrete Reinforcement
A416/A416M Specification for Low-Relaxation, Seven-Wire Steel Strand for Prestressed Concrete
A421/A421M Specification for Stress-Relieved Steel Wire for Prestressed Concrete
A615/A615M Specification for Deformed and Plain Carbon-Steel Bars for Concrete Reinforcement
A706/A706M Specification for Deformed and Plain Low-Alloy Steel Bars for Concrete Reinforcement
A1064/A1064M Specification for Carbon-Steel Wire and Welded Wire Reinforcement, Plain and Deformed, for Concrete
C33/C33M Specification for Concrete Aggregates
C39/C39M Test Method for Compressive Strength of Cylindrical Concrete Specimens
C94/C94M Specification for Ready-Mixed Concrete
1
This specification is under the jurisdiction of ASTM Committee C27 on Precast Concrete Products and is the direct responsibility of Subcommittee C27.30 on Water
and Wastewater Containers.
Current edition approved May 1, 2018Aug. 1, 2021. Published May 2018August 2021. Originally approved in 1979. Last previous edition approved in 20162018 as
C913 – 16.C913 – 18. DOI: 10.1520/C0913-18.10.1520/C0913-21.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C913 − 21
C125 Terminology Relating to Concrete and Concrete Aggregates
C150/C150M Specification for Portland Cement
C173/C173M Test Method for Air Content of Freshly Mixed Concrete by the Volumetric Method
C231/C231M Test Method for Air Content of Freshly Mixed Concrete by the Pressure Method
C260/C260M Specification for Air-Entraining Admixtures for Concrete
C330/C330M Specification for Lightweight Aggregates for Structural Concrete
C478C478/C478M Specification for Circular Precast Reinforced Concrete Manhole Sections (Metric) C0478_C0478M
C494/C494M Specification for Chemical Admixtures for Concrete
C595/C595M Specification for Blended Hydraulic Cements
C618 Specification for Coal Fly Ash and Raw or Calcined Natural Pozzolan for Use in Concrete
C685/C685M Specification for Concrete Made by Volumetric Batching and Continuous Mixing
C890 Practice fo
...
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: C913 − 21
Standard Specification for
1
Precast Concrete Water and Wastewater Structures
This standard is issued under the fixed designation C913; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope A416/A416M Specification for Low-Relaxation, Seven-
Wire Steel Strand for Prestressed Concrete
1.1 This specification covers the recommended design re-
A421/A421M Specification for Stress-Relieved Steel Wire
quirements and manufacturing practices for monolithic or
for Prestressed Concrete
sectional precast concrete water and wastewater structures with
A615/A615M Specification for Deformed and Plain Carbon-
the exception of concrete pipe, box culverts, utility structures,
Steel Bars for Concrete Reinforcement
septic tanks, grease interceptor tanks, and items included under
A706/A706M Specification for Deformed and Plain Low-
the scope of Specification C478/C478M.
Alloy Steel Bars for Concrete Reinforcement
NOTE 1—Water and wastewater structures are defined as solar heating
A1064/A1064M Specification for Carbon-Steel Wire and
reservoirs, cisterns, holding tanks, leaching tanks, extended aeration tanks,
Welded Wire Reinforcement, Plain and Deformed, for
wet wells, pumping stations, distribution boxes, oil-water separators,
Concrete
treatment plants, manure pits, catch basins, drop inlets, and similar
C33/C33M Specification for Concrete Aggregates
structures.
NOTE 2—Installation and sealant requirements should receive special
C39/C39M Test Method for Compressive Strength of Cylin-
consideration due to special features of the application.
drical Concrete Specimens
1.2 The values stated in inch-pound units are to be regarded C94/C94M Specification for Ready-Mixed Concrete
as the standard. The values given in parentheses are for C125 Terminology Relating to Concrete and Concrete Ag-
information only. gregates
C150/C150M Specification for Portland Cement
1.3 This standard does not purport to address all of the
C173/C173M Test Method for Air Content of Freshly Mixed
safety concerns, if any, associated with its use. It is the
Concrete by the Volumetric Method
responsibility of the user of this standard to establish appro-
C231/C231M Test Method for Air Content of Freshly Mixed
priate safety, health, and environmental practices and deter-
Concrete by the Pressure Method
mine the applicability of regulatory limitations prior to use.
C260/C260M Specification for Air-Entraining Admixtures
1.4 This international standard was developed in accor-
for Concrete
dance with internationally recognized principles on standard-
C330/C330M Specification for Lightweight Aggregates for
ization established in the Decision on Principles for the
Structural Concrete
Development of International Standards, Guides and Recom-
C478/C478M Specification for Circular Precast Reinforced
mendations issued by the World Trade Organization Technical
Concrete Manhole Sections
Barriers to Trade (TBT) Committee.
C494/C494M Specification for Chemical Admixtures for
Concrete
2. Referenced Documents
2 C595/C595M Specification for Blended Hydraulic Cements
2.1 ASTM Standards:
C618 Specification for Coal Fly Ash and Raw or Calcined
A184/A184M Specification for Welded Deformed Steel Bar
Natural Pozzolan for Use in Concrete
Mats for Concrete Reinforcement
C685/C685M Specification for Concrete Made by Volumet-
ric Batching and Continuous Mixing
1
This specification is under the jurisdiction of ASTM Committee C27 on Precast C890 Practice for Minimum Structural Design Loading for
Concrete Products and is the direct responsibility of Subcommittee C27.30 on Water
Monolithic or Sectional Precast Concrete Water and
and Wastewater Containers.
Wastewater Structures
Current edition approved Aug. 1, 2021. Published August 2021. Originally
C989/C989M Specification for Slag Cement for Use in
approved in 1979. Last previous edition approved in 2018 as C913 – 18. DOI:
10.1520/C0913-21.
Concrete and Mortars
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
C990 Specification for Joints for Concrete Pipe, Manholes,
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
and Precast Box Sections Using Preformed Flexible Joint
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. Sealants
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C913 − 21
C1157/C1157M Per
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.