Metal bellows expansion joints for pressure applications

This European Standard specifies the requirements for design, manufacture and installation of metal bellows expansion joints for pressure applications, i.e. maximum allowable pressure greater than 0,5 bar.

Kompensatoren mit metallischen Bälgen für Druckanwendungen

Dieser Europäische Normentwurf legt Anforderungen an die Konstruktion, Herstellung und den Einbau von
Kompensatoren mit metallischen Bälgen für Druckanwendungen fest, d. h. für einen maximal zulässigen
Druck über 0,5 bar.

Compensateurs de dilatation à soufflets métalliques pour appareils à pression

Cette Norme européenne décrit les exigences de conception, de fabrication et d’installation applicables aux compensateurs de dilatation à soufflets métalliques pour applications sous pression, c’est-à-dire des pressions maximales admissibles supérieures à 0,5 bar.
Les compensateurs de dilatation à soufflets métalliques sont utilisés comme composants de tuyauteries ou comme éléments de récipients sous pression.

Kompenzatorji s kovinskimi mehovi v tlačnih cevovodih

General Information

Status
Withdrawn
Publication Date
20-Jan-2009
Withdrawal Date
28-Feb-2012
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
29-Feb-2012
Completion Date
29-Feb-2012

Relations

Buy Standard

Standard
EN 14917:2009
English language
198 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN 14917:2004
English language
145 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kompensatoren mit Metellischen Bälgen für DruckanwendungenCompensateurs de dilatation a soufflets métalliques pour tuyauteurs et appareils a pressionMetal bellows expansion joints for pressure applications23.040.99Drugi sestavni deli za cevovodeOther pipeline componentsICS:Ta slovenski standard je istoveten z:EN 14917:2009SIST EN 14917:2009en01-april-2009SIST EN 14917:2009SLOVENSKI
STANDARD



SIST EN 14917:2009



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 14917January 2009ICS 23.040.99 English VersionMetal bellows expansion joints for pressure applicationsCompensateurs de dilatation à soufflets métalliques pourappareils à pressionKompensatoren mit metallischen Bälgen fürDruckanwendungenThis European Standard was approved by CEN on 6 September 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2009 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 14917:2009: ESIST EN 14917:2009



EN 14917:2009 (E) 2 Contents Page Foreword .5Introduction .61Scope .72Normative references .73Terms and definitions . 104Classification . 114.1Classification of expansion joints . 114.1.1Axial . 114.1.2Angular . 114.1.3Lateral . 114.1.4Universal . 114.2Classification of the parts of expansion joints . 164.2.1Main pressure bearing parts (A) . 164.2.2Pressure parts other than main pressure-bearing parts (B) . 164.2.3Attachments to main pressure-bearing parts and to pressure parts (C) . 164.2.4Other parts (D) . 165Materials . 185.1General . 185.1.1Materials for pressure-bearing parts .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.