Metal bellows expansion joints for pressure applications

This European Standard specifies the requirements for design, manufacture and installation of metal bellows expansion joints for pressure applications, i.e. maximum allowable pressure greater than 0,5 bar.

Kompensatoren mit metallischen Bälgen für Druckanwendungen

Diese Europäische Norm legt Anforderungen an die Konstruktion, Herstellung und den Einbau von Kompen-satoren mit metallischen Bälgen für Druckanwendungen fest, d. h. für einen maximal zulässigen Druck über 0,5 bar.

Compensateurs de dilatation à soufflets métalliques pour appareils à pression

Cette Norme européenne décrit les exigences de conception, de fabrication et d’installation applicables aux
compensateurs de dilatation à soufflets métalliques pour applications sous pression, c’est-à-dire des
pressions maximales admissibles supérieures à 0,5 bar.

Kompenzatorji s kovinskimi mehovi v tlačnih cevovodih

Ta evropski standard določa zahteve za načrtovanje, izdelavo in namestitev kompenzatorjev s kovinskimi mehovi v tlačnih cevovodih, pri čemer je najvišji dovoljeni tlak višji od 0,5 bar.

General Information

Status
Withdrawn
Publication Date
06-Mar-2012
Withdrawal Date
27-Jul-2021
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
28-Jul-2021

Relations

Buy Standard

Standard
EN 14917:2009+A1:2012
English language
206 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kompensatoren mit metallischen Bälgen für DruckanwendungenCompensateurs de dilatation à soufflets métalliques pour appareils à pressionMetal bellows expansion joints for pressure applications23.040.99Drugi sestavni deli za cevovodeOther pipeline componentsICS:Ta slovenski standard je istoveten z:EN 14917:2009+A1:2012SIST EN 14917:2009+A1:2012en,fr,de01-julij-2012SIST EN 14917:2009+A1:2012SLOVENSKI
STANDARD



SIST EN 14917:2009+A1:2012



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 14917:2009+A1
March 2012 ICS 23.040.99 Supersedes EN 14917:2009English Version
Metal bellows expansion joints for pressure applications
Compensateurs de dilatation à soufflets métalliques pour appareils à pression
Kompensatoren mit metallischen Bälgen für Druckanwendungen This European Standard was approved by CEN on 6 September 2008 and includes Amendment 1 approved by CEN on 10 January 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14917:2009+A1:2012: ESIST EN 14917:2009+A1:2012



EN 14917:2009+A1:2012 (E) 2 Contents Page Foreword .5Introduction .61Scope .72Normative references .73Terms and definitions . 104Classification . 114.1Classification of expansion joints . 114.1.1Axial . 114.1.2Angular . 114.1.3Lateral . 114.1.4Universal . 114.2Classification of the parts of expansion joints . 164.2.1!!!!Main pressure-bearing parts (A)"""" . 164.2.2Pressure parts other than main pressure-bearing parts (B) . 164.2.3Attachments to main pressure-bearing parts and to pressure parts (C) . 164.2.4Other parts (D) . 165Materials . 185.1General .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.