EN 12350-3:2019
(Main)Testing fresh concrete - Part 3: Vebe test
Testing fresh concrete - Part 3: Vebe test
This document specifies a method for determining the consistency of fresh concrete by means of the Vebe time.
The test is suitable for specimens having a declared value of D of the coarsest fraction of aggregates actually used in the concrete (Dmax) not greater than 63 mm.
If the Vebe time is less than 5 s or more than 30 s, the concrete has a consistency for which the Vebe test is unsuitable.
Prüfung von Frischbeton - Teil 3: Vébé-Prüfung
Dieses Dokument legt ein Verfahren zur Bestimmung der Konsistenz von Frischbeton mit Hilfe der Vébé Zeit fest.
Die Prüfung ist für Proben geeignet, deren deklarierter Wert D des Größtkorns der tatsächlich im Beton verwendeten Gesteinskörnungen (Dmax) nicht größer als 63 mm ist.
Wenn die Vébé Zeit weniger als 5 s oder mehr als 30 s beträgt, hat der Beton eine Konsistenz, für die die Vébé Prüfung nicht geeignet ist.
Essais pour béton frais - Partie 3 : Essai Vébé
Le présent document spécifie une méthode de détermination de la consistance du béton frais par l’essai Vébé.
L’essai est adapté aux échantillons ayant une valeur déclarée de D pour les plus gros granulats effectivement utilisés dans le béton (Dmax) inférieure ou égale à 63 mm.
Si le résultat à l’essai Vébé (temps Vébé) est inférieur à 5 s ou supérieur à 30 s, le béton présente une consistance qui ne peut être déterminée au moyen de l’essai Vébé.
Preskušanje svežega betona - 3. del: Vebe preskus
Ta evropski standard določa metodo za določanje konsistence svežega betona s pomočjo časa Vebe.
Preskus je primeren za primerke, pri katerih je deklarirana vrednost D najbolj grobega agregata, ki je dejansko uporabljen v betonu (Dmax), manjša od 63 mm.
Če je čas Vebe manj kot 5 s ali več kot 30 s, ima beton konsistenco, za katero preskus Vebe ni primeren.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2019
Nadomešča:
SIST EN 12350-3:2009
Preskušanje svežega betona - 3. del: Vebe preskus
Testing fresh concrete - Part 3: Vebe test
Prüfung von Frischbeton - Teil 3: Vébé-Prüfung
Essais pour béton - Partie 3 : Essai Vébé
Ta slovenski standard je istoveten z: EN 12350-3:2019
ICS:
91.100.30 Beton in betonski izdelki Concrete and concrete
products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 12350-3
EUROPEAN STANDARD
NORME EUROPÉENNE
June 2019
EUROPÄISCHE NORM
ICS 91.100.30 Supersedes EN 12350-3:2009
English Version
Testing fresh concrete - Part 3: Vebe test
Essais pour béton frais - Partie 3 : Essai Vébé Prüfung von Frischbeton - Teil 3: Vébé-Prüfung
This European Standard was approved by CEN on 29 April 2019.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12350-3:2019 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Principle . 4
5 Apparatus . 4
6 Sampling . 5
7 Procedure. 5
8 Test result . 6
9 Test report . 6
10 Precision . 7
European foreword
This document (EN 12350-3:2019) has been prepared by Technical Committee CEN/TC 104 “Concrete
and related products”, the secretariat of which is held by SN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by December 2019, and conflicting national standards
shall be withdrawn at the latest by December 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 12350-3:2009.
This standard is one of a series on testing concrete.
EN 12350, Testing fresh concrete, consists of the following parts:
— Part 1: Sampling and common apparatus
— Part 2: Slump test
— Part 3: Vebe test
— Part 4: Degree of compactability
— Part 5: Flow table test
— Part 6: Density
— Part 7: Air content – Pressure methods
— Part 8: Self-compacting concrete – Slump-flow test
— Part 9: Self-compacting concrete – V-funnel test
— Part 10: Self-compacting concrete – L-box test
— Part 11: Self-compacting concrete – Sieve segregation test
— Part 12: Self-compacting concrete – J-ring test
The following amendments have been made to the 2009 edition of this standard:
a) editorial revision;
b) use of a trowel to strike off concrete;
c) reference to common apparatus and specification given in EN 12350-1.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
1 Scope
This document specifies a method for determining the consistence of fresh concrete by means of the
Vebe time.
The test is suitable for specimens having a declared value of D of the coarsest fraction of aggregates
actually used in the concrete (D ) not greater than 63 mm.
max
If the Vebe time is less than 5 s or more than 30 s, the concrete has a consistence for which the Vebe test
is unsuitable.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 12350-1, Testing fresh concrete — Part 1: Sampling and common apparatus
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at http://www.electropedia.org/
— ISO Online browsing platform: available at http://www.iso.org/obp
4 Principle
The fresh concrete is compacted into a slump cone. The cone is lifted clear of the concrete and a
transparent disc is swung over the top of the concrete and carefully lowered until it comes in contact
with the concrete. The slump of the concrete is recorded. The vibrating table is started and the time
taken for the lower surface of the transparent disc to be fully in contact with the grout (the Vebe time),
is measured.
5 Apparatus
5.1 Common app
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.