EN 14307:2015
(Main)Thermal insulation products for building equipment and industrial installations - Factory made extruded polystyrene foam (XPS) products - Specification
Thermal insulation products for building equipment and industrial installations - Factory made extruded polystyrene foam (XPS) products - Specification
This European Standard specifies the requirements for factory made extruded polystyrene foam products which are used for the thermal insulation of building equipment and industrial installations with an operating temperature in the range of approximately - 180 °C to + 75 °C.
Below an operating temperature of - 50 °C, special tests regarding the suitability of the material in the intended application are advised (e.g. liquefaction of oxygen). Manufacturer's advice should be heeded in all cases.
The products are manufactured in the form of faced or unfaced boards, pipe sections, segments and prefabricated ware.
This European Standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling.
Products covered by this standard are also used in prefabricated thermal insulating systems and composite panels; the performance of systems incorporating these products is not covered.
This European Standard does not specify the required level of a given property that should be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application can be found in regulations and invitations to tender.
Products with a declared thermal conductivity greater than 0,060 W/(m·K) at a mean temperature of 10 °C are not covered by this standard.
This European Standard does not cover products intended to be used for the insulation of the building structure nor for acoustical insulation.
Wärmedämmstoffe für die technische Gebäudeausrüstung und für betriebstechnische Anlagen in der Industrie - Werkmäßig hergestellte Produkte aus extrudiertem Polystyrolschaum (XPS) - Spezifikation
Diese Europäische Norm legt die Anforderungen an werkmäßig hergestellte Produkte aus extrudiertem Polystyrolschaum fest, die als Wärmedämmstoffe für die technische Gebäudeausrüstung und für betriebstechnische Anlagen in der Industrie in einem Betriebstemperaturbereich von etwa − 180 °C bis + 75 °C benutzt werden.
Bei einer Betriebstemperatur unterhalb von − 50 °C sind besondere Prüfungen bezüglich der Eignung der Produkte für den beabsichtigten Anwendungsfall ratsam (z. B. Sauerstoffverflüssigung). In jedem Fall sollten die Empfehlungen des Herstellers beachtet werden.
Die Produkte werden in Form von kaschierten oder unkaschierten Platten, Rohrschalen, Segmenten und vorgeformter Dämmung hergestellt.
Diese Europäische Norm beschreibt die Produkteigenschaften und enthält Verfahren zur Prüfung, Konformitätsbewertung, Kennzeichnung und Etikettierung.
Die von dieser Norm abgedeckten Produkte werden auch in vorgefertigten Wärmedämmsystemen und Mehrschicht-Verbundplatten angewendet; die Eigenschaften von Systemen, in die diese Produkte integriert sind, werden nicht behandelt.
Diese Europäische Norm legt für die einzelnen Eigenschaften keine Leistungsstufen fest, die ein Produkt erreichen sollte, um für einen bestimmten Anwendungsfall tauglich zu sein. Die für bestimmte Anwendungen benötigten Stufen können Regelwerken oder Ausschreibungen entnommen werden.
Diese Norm gilt nicht für Produkte mit einem Nennwert der Wärmeleitfähigkeit größer als 0,060 W/(m ⋅ K) bei einer Mitteltemperatur von 10 °C.
Diese Europäische Norm gilt nicht für Produkte, die zur Dämmung des Bauwerks bestimmt sind und Produkte, die zur Schalldämmung bestimmt sind.
Produits isolants thermiques pour l'équipement du bâtiment et les installations industrielles - Produits manufacturés en mousse de polystyrène extrudé (XPS) - Spécification
La présente Norme européenne spécifie les exigences relatives aux produits manufacturés en mousse de polystyrène extrudé, utilisés pour l’isolation thermique de l’équipement du bâtiment et des installations industrielles, dont la température de service est approximativement comprise entre - 180 °C et + 75 °C.
Pour une température de service inférieure à - 50 °C, des essais particuliers sont recommandés pour s'assurer de l'aptitude à l'emploi du produit dans l'application visée (liquéfaction de l'oxygène, par exemple). Il convient de se référer systématiquement aux conseils du fabricant.
Les produits sont manufacturés sous forme de panneaux, coquilles, segments et articles préfabriqués, avec ou sans parement.
La présente Norme européenne décrit les caractéristiques de ces produits et comprend des modes opératoires d’essai, d’évaluation de la conformité, de marquage et d’étiquetage.
Les produits couverts par la présente norme sont également utilisés dans les systèmes d’isolation thermique préfabriqués et les panneaux composites ; les performances des systèmes incorporant ces produits ne sont pas traitées.
La présente Norme européenne ne spécifie pas le niveau requis d'une propriété donnée qu'il convient qu'un produit atteigne pour démontrer son aptitude à l'emploi dans une application particulière. Les niveaux requis pour une application donnée peuvent être trouvés dans les réglementations et les appels d’offre.
Les produits dont la conductivité thermique déclarée est supérieure à 0,060 W/(m·K) à une température moyenne de 10 °C ne sont pas couverts par la présente norme.
La présente Norme européenne ne couvre ni les produits destinés à l’isolation des structures de bâtiment ni les produits d’isolation acoustique.
Toplotnoizolacijski proizvodi za opremo stavb in industrijske inštalacije - Proizvodi iz ekstrudiranega polistirena (XPS) - Specifikacija
Ta evropski standard določa zahteve za proizvode iz ekstrudiranega polistirena, ki se uporabljajo za toplotno izolacijo opreme stavb in industrijskih inštalacij z razponom delovne temperature približno od –180 °C do 75 °C. OPOMBA Pod delovno temperaturo –50 °C se priporočajo posebni preskusi glede primernosti proizvodov za predvideno vrsto uporabe (npr. utekočinjenje kisika). V vseh primerih naj bi upoštevali napotke proizvajalca. Proizvodi so izdelani v obliki prevlečenih ali neprevlečenih plošč, vodovodnih odsekov, segmentov in montažne opreme. Ta standard opisuje lastnosti proizvodov ter zajema postopke za preskušanje, vrednotenje skladnosti, označevanje in etiketiranje. Proizvodi iz tega standarda se uporabljajo tudi v montažnih sistemih toplotne izolacije in vezanih ploščah; lastnosti sistemov iz teh proizvodov niso opisane. Ta evropski standard ne določa zahtevane ravni določene lastnosti, ki jo mora proizvod doseči, da se dokaže njegova primernost namenu za posamezno vrsto uporabe. Zahtevane ravni za posamezno uporabo je mogoče najti v uredbah in javnih razpisih. Proizvodi z deklarirano toplotno prevodnostjo, višjo od 0,060 W/mK pri povprečni temperaturi 10 °C, v tem standardu niso zajeti. Ta standard ne zajema proizvodov za izolacijo stavbne strukture ali za zvočno izolacijo.
General Information
Relations
Overview
EN 14307:2015 is the CEN European Standard that specifies requirements for factory-made extruded polystyrene foam (XPS) products used for the thermal insulation of building equipment and industrial installations. It covers XPS in forms such as faced or unfaced boards, pipe sections, segments and prefabricated ware. The standard defines product characteristics, test methods, conformity assessment, marking and labelling, and addresses regulatory compliance under the EU Construction Products Regulation (CPR).
Key limits and scope notes:
- Applicable operating temperature range: approximately -180 °C to +75 °C.
- Below -50 °C, special suitability tests are advised (e.g., risks such as oxygen liquefaction); follow manufacturer guidance.
- Excludes products with declared thermal conductivity > 0.060 W/(m·K) at a mean temperature of 10 °C.
- Does not cover insulation of the building structure or acoustical insulation, nor the performance of complete prefabricated systems or composite panels that incorporate the products.
Key Topics and Requirements
EN 14307:2015 focuses on the following technical topics and requirements:
- Thermal conductivity and procedures to determine declared and aged values.
- Dimensions and tolerances, and dimensional stability under defined conditions.
- Reaction to fire and requirements for fire classification as placed on the market.
- Durability characteristics, including long-term performance aspects.
- Mechanical properties for specific applications: compressive strength/stress, compressive creep, deformation under load.
- Moisture-related properties: water vapour diffusion, short-term and long-term water absorption.
- Safety and environmental aspects: trace soluble ions, pH, release of dangerous substances, and continuous glowing combustion.
- Testing framework: sampling, conditioning and standard test methods; Annexes provide factory production control (Annex A) and ageing procedures for thermal conductivity (Annex B).
- Conformity & marking: assessment and verification of constancy of performance (AVCP), designation codes and CE marking clauses (Annex ZA).
Applications and Practical Use
EN 14307 applies where durable, factory-made XPS insulation is required for:
- District heating/cooling pipework, process piping and refrigeration lines.
- HVAC ductwork and technical building services.
- Industrial installations that operate within the specified temperature range.
- Prefabricated insulating elements used in industrial equipment (note: performance of whole systems is outside the standard).
Practical considerations:
- Select XPS products that meet the required thermal conductivity, mechanical and fire properties for the intended service conditions.
- For very low-temperature service (< -50 °C), require supplier validation and additional testing.
- Use the standard’s designation code, marking and AVCP rules to verify compliance for procurement and tendering.
Who Should Use This Standard
- XPS manufacturers and quality managers (FPC and product certification)
- Specifiers, engineers and thermal insulation designers
- Contractors and installers of building equipment and industrial systems
- Test laboratories, conformity assessment bodies and procurement authorities
- Regulatory/compliance officers implementing CPR requirements
Related Standards
EN 14307 is part of a CEN package of factory-made insulation specifications including EN 14303 (MW), EN 14304 (FEF), EN 14305 (CG), EN 14308 (PUR/PIR), EN 14309 (EPS) and others - consult these when selecting alternative insulation materials.
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Toplotnoizolacijski proizvodi za opremo stavb in industrijske inštalacije - Proizvodi iz ekstrudiranega polistirena (XPS) - SpecifikacijaWärmedämmstoffe für die technische Gebäudeausrüstung und für betriebstechnische Anlagen in der Industrie - Werkmäßig hergestellte Produkte aus extrudiertem Polystyrolschaum (XPS) - SpezifikationProduits isolants thermiques pour l'équipement du bâtiment et les installations industrielles - Produits manufacturés en mousse de polystyrène extrudé (XPS) - SpécificationThermal insulation products for building equipment and industrial installations - Factory made extruded polystyrene foam (XPS) products - Specification91.100.60Thermal and sound insulating materialsICS:Ta slovenski standard je istoveten z:EN 14307:2015SIST EN 14307:2016en,fr,de01-februar-2016SIST EN 14307:2016SLOVENSKI
STANDARDSIST EN 14307:2010+A1:20131DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 14307
December
t r s w ICS
{ sä s r rä x r Supersedes EN
s v u r yã t r r { ªA sã t r s uEnglish Version
Thermal insulation products for building equipment and industrial installations æ Factory made extruded roducts æ Specification Produits isolants thermiques pour l 5équipement du bâtiment et les installations industrielles æ Produits æ Spécification
Wärmedämmstoffe für die technische Gebäudeausrüstung und für betriebstechnische Anlagen in der Industrie æ Werkmäßig hergestellte Spezifikation This European Standard was approved by CEN on
t v October
t r s wä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey andUnited Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
t r s w CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s v u r yã t r s w ESIST EN 14307:2016
Factory production control . 20 Annex B (normative)
Determination of the aged values of thermal conductivity . 22 SIST EN 14307:2016
Additional properties . 24 C.1 General . 24 C.2 Behaviour under cyclic loading . 24 C.3 Compressive modulus of elasticity . 24 C.4 Bending strength . 24 C.5 Shear strength . 24 C.6 Deformation under specified compressive load and temperature conditions . 25 C.7 Compressive creep . 25 C.8 Tensile strength perpendicular to facings . 26 C.9 Long term water absorption by diffusion . 26 C.10 Long term water absorption by immersion . 26 C.11 Freeze–thaw resistance . 27 C.12 Apparent density . 27 C.13 Coefficient of thermal expansion . 27 C.14 Closed cell content . 27 Annex ZA (informative)
Clauses of this European Standard addressing the provisions of the EU Construction Products Regulation . 29 ZA.1 Scope and relevant characteristics . 29 ZA.2 Procedures for AVCP of factory made extruded polystyrene foam products . 31 ZA.3 CE Marking and labelling . 38 Bibliography . 40
is the thermal conductivity W/(m·K) D is the declared thermal conductivity W/(m·K)
is the water vapour diffusion resistance factor — Sb is the deviation from squareness of the edge (width or length) mm/m Sd is the deviation from squareness of the edge (thickness) mm/m Smax is the deviation from flatness mm 10 is the compressive stress at 10 % deformation kPa m is the compressive strength kPa v is the deviation from the squareness for pipe section mm/m Wp is the short-term water absorption by partial immersion kg/m2 Z is the water vapour resistance m2 · h · Pa/mg CL is the symbol of the declared level for soluble chloride ions
CS(10\Y) is the symbol of the declared level for compressive stress or strength
DS(TH) is the symbol of the declared value for the dimensional stability under specified temperature and humidity conditions
MU is the symbol of the declared level for water vapour diffusion resistance factor
NA is the symbol of the declared level of soluble sodium ions
pH is the symbol of the declared level of the pH value
SI is the symbol of the declared level of soluble silicate ions
ST(+) is the symbol of the declared level for maximum service temperature
ST(-) is the symbol of the declared level for minimum service temperature
T is the symbol of the declared class for thickness tolerances
WS is the symbol of the declared level for short-term water absorption by partial immersion
Z is the symbol of the declared value for water vapour resistance
3.2.2 Abbreviations used in this standard AVCP is Assessment and Verification of Constancy of Performance (previously named attestation of conformity) DoP is Declaration of Performance FPC is Factory Production Control PTD is Product Type Determination (previously named ITT for Initial Type Test) RtF is Reaction to Fire SBI is Single Burning Item ThIBEII is Thermal Insulation for Building Equipment and Industrial Installations VCP is Verification of Constancy of Performance (previously named evaluation of conformity) XPS is eXtruded PolyStyrene foam 4 Requirements 4.1 General Product properties shall be assessed in accordance with Clause 5. To comply with this standard, products shall meet the requirements of 4.2, and the requirements of 4.3 as appropriate. NOTE
Information on additional properties is given in Annex C. One test result for a product property is the average of the measured values on the number of test specimens given in Table 5. Apparent density is a useful parameter, among others, for the identification but it should not be used as a basis for the quality assessment of XPS products. Apparent density of XPS boards and billets, if voluntary declared by the manufacturer will be determined in accordance with EN 1602, Thermal insulating products for building applications — Determination of the apparent density. Apparent density of pipe sections, if voluntary declared by the manufacturer will be determined in accordance with EN 13470, Thermal insulating products for building equipment and industrial installations — Determination of the apparent density of preformed pipe insulation. SIST EN 14307:2016
values below 0,1 W/(m·K) and in 0,001 W/(m·K) for
values above 0,1 W/(m·K). This shall be used as a reference for the verification of the declaration. When thermal conductivity is declared as a table derived from the equation, rounding upwards to the next 0,001 W/(m·K) has to be done for the full range of the thermal conductivity. NOTE Determinations of the declared thermal conductivity of pipe sections, following EN ISO 8497, having joints in metering area, include the effects of these joints as defined in EN ISO 23993. 4.2.2 Dimensions and tolerances 4.2.2.1 Linear dimensions of boards The length, l, and width, b, shall be determined in accordance with EN 822, the squareness, Sb, in accordance with EN 824, and flatness, Smax, in accordance with EN 825. No test result shall deviate from the declared values by more than the tolerances given in Table 1. Table 1 — Tolerances of length, width, squareness and flatness of boards Length or width mm Tolerances Length or width mm Squareness on length and width Sb mm/m Flatness Smax. mm Less than 1 000 1 000 to 2 000 > 2 000 to 4 000 > 4 000 ±8 ±10 ±10 ±10 5 5 5 5 7,0 14,0 28,0 35,0 SIST EN 14307:2016
¶ dD
¶ 120 > 120 T2 – 1,5 – 1,5 – 1,5 + 1,5 + 1,5 + 1,5 < 50 50
¶ dD
¶ 120 > 120 T3 – 1 – 1 – 1 + 1 + 1 + 1 < 50 50
¶ dD
¶ 120 > 120 4.2.2.3 Dimensions and tolerances of pipe sections and segments The length, l, thickness, d, inside diameter, Di, the deviation from the squareness, v, and the deviation from the linearity, L, of pipe sections and segments shall be tested in accordance with EN 13467. Products with a facing or natural skin shall be tested without removing them. No test result shall deviate from the declared values by more than the tolerances given in Table 3. Tolerances on prefabricated wares may be agreed between the parties. Table 3 — Tolerances for pipe sections and segments Length, l ±10 mm Thickness, d a, ±3 mm or ± 5 % b Inside diameter, Di – 0 mm / + 4 mm or + 2 % b Squareness, v ±6 mm or ± 2 % b Linearity, L ±6 mm a
The tolerances only apply to unfaced products. The thickness of any facing exceeding 2 mm shall be indicated in the manufacturer’s literature. b
The greater value applies. NOTE Smaller tolerances may be declared by a producer. 4.2.3 Dimensional stability Dimensional stability under specified temperature and humidity conditions shall be determined in accordance with EN 1604. The test shall be carried out after storage for 48 h at (23 ± 2) °C and (90 ± 5) % relative humidity. The relative changes in length, l, in width, b, and in thickness, d, shall not exceed 2 %. SIST EN 14307:2016
General The appropriate durability characteristics have been considered and are covered in 4.2.5.2, 4.2.5.3 and 4.2.5.4. 4.2.5.2 Durability of reaction to fire against ageing/degradation and high temperature The reaction to fire performance of XPS products does not change with time within their range of service temperature. 4.2.5.3 Durability of thermal resistance against ageing/degradation The declared thermal conductivity of XPS products does not change with time. This is covered by 4.2.1 thermal conductivity, Annex B determination of the aged value of thermal conductivity and 4.2.2 dimensions and tolerances. 4.2.5.4 Durability of thermal resistance against high temperature The thermal conductivity of XPS products does not change with time at a high temperature within their declared operating temperature range. This is covered by 4.3.2 maximum service temperature (dimensional stability). 4.3 For specific applications 4.3.1 General If there is no intended requirement for a property described in 4.3, for a product in use, then that property does not need to be determined and declared by the manufacturer. XPS pipe sections and prefabricated ware are sawed or abraded from flat boards. If not specified hereafter, the declarations for the specific characteristics correspond to the flat boards used for their fabrication. 4.3.2 Maximum service temperature The maximum service temperature, ST(+), shall be determined in accordance with EN 14706. At the maximum service temperature, ST(+), no test result shall have a variation of dimensions exceeding ± 3 %. SIST EN 14307:2016
· 100 CS(10\Y) 150
· 150 CS(10\Y) 200
· 200 CS(10\Y) 250
· 250 CS(10\Y) 300
· 300 CS(10\Y) 400
· 400 CS(10\Y) 500
· 500 CS(10\Y) 600
· 600 CS(10\Y) 700
· 700 CS(10\Y) 800
· 800 CS(10\Y) 1000
· 1 000 4.3.5 Water vapour diffusion transmission properties Water vapour diffusion transmission properties shall be determined in accordance with EN 12086, and declared as the water vapour diffusion resistance factor, , for homogeneous products and as the water vapour resistance, Z, for faced or non-homogeneous products. No test result of
shall be less than the declared level, MU, chosen from the following levels: 50; 80; 100; 150; 200; 250; 300. If Z is declared, no test result of Z shall be less than the declared value. Alternatively, for the declaration of water vapour transmission properties, the values quoted in EN ISO 10456 may be used. SIST EN 14307:2016
of the range. If facings have been removed, this and the reason for the remove shall be stated in the test report. 5.3.3 Reaction to fire The tests shall be carried out in accordance with EN 13501-1. Rules for mounting and fixing are given in EN 15715:2009. Annex A of EN 15715:2009 gives tables for product and installation parameters for flat products and pipe insulation products as placed on the market. Installation parameters for standardized assemblies are only given for flat products. A conditioning period of six weeks applies before testing. SIST EN 14307:2016
number of measurements to get one test result Specific conditions No. Title Flat / Board Cylindrical 4.2.1 Thermal conductivity EN 12667 or EN 12939 EN 12667 or EN 12939 for Di > 500 EN ISO 8497 for Di
¶ 500 See EN 12667, EN 12939 or EN ISO 8497 1
See Annex B 4.2.2.1 Board length and width EN 822
Full size 1
Board squareness EN 824
Full size 1 Where relevant the method to determine the squareness of the edge of boards with special edge treatment shall be agreed between parties. Board flatness EN 825
Full size 1
4.2.2.2 Board thickness EN 823
Full size 1 Load (250 ± 5) Pa 4.2.2.3 Pipe section dimensions and tolerances
EN 13467 Full size 1
4.2.3 Dimensional stability EN 1604
200 × 200 2 Condition specimens for 45 days. Test conditions: 23 °C, 90 % RH. 4.2.4 Reaction to fire of the product as placed on the market See EN 13501–1, EN ISO 11925-2 and EN 13823 See EN 15715:2009 4.3.2 Maximum service temperature EN 14706
Boards (100 × 100) × d d = 50 or 100 3 Temperature gradient
50 K/h maximum Condition specimen
45 days
...
Frequently Asked Questions
EN 14307:2015 is a standard published by the European Committee for Standardization (CEN). Its full title is "Thermal insulation products for building equipment and industrial installations - Factory made extruded polystyrene foam (XPS) products - Specification". This standard covers: This European Standard specifies the requirements for factory made extruded polystyrene foam products which are used for the thermal insulation of building equipment and industrial installations with an operating temperature in the range of approximately - 180 °C to + 75 °C. Below an operating temperature of - 50 °C, special tests regarding the suitability of the material in the intended application are advised (e.g. liquefaction of oxygen). Manufacturer's advice should be heeded in all cases. The products are manufactured in the form of faced or unfaced boards, pipe sections, segments and prefabricated ware. This European Standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling. Products covered by this standard are also used in prefabricated thermal insulating systems and composite panels; the performance of systems incorporating these products is not covered. This European Standard does not specify the required level of a given property that should be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application can be found in regulations and invitations to tender. Products with a declared thermal conductivity greater than 0,060 W/(m·K) at a mean temperature of 10 °C are not covered by this standard. This European Standard does not cover products intended to be used for the insulation of the building structure nor for acoustical insulation.
This European Standard specifies the requirements for factory made extruded polystyrene foam products which are used for the thermal insulation of building equipment and industrial installations with an operating temperature in the range of approximately - 180 °C to + 75 °C. Below an operating temperature of - 50 °C, special tests regarding the suitability of the material in the intended application are advised (e.g. liquefaction of oxygen). Manufacturer's advice should be heeded in all cases. The products are manufactured in the form of faced or unfaced boards, pipe sections, segments and prefabricated ware. This European Standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling. Products covered by this standard are also used in prefabricated thermal insulating systems and composite panels; the performance of systems incorporating these products is not covered. This European Standard does not specify the required level of a given property that should be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application can be found in regulations and invitations to tender. Products with a declared thermal conductivity greater than 0,060 W/(m·K) at a mean temperature of 10 °C are not covered by this standard. This European Standard does not cover products intended to be used for the insulation of the building structure nor for acoustical insulation.
EN 14307:2015 is classified under the following ICS (International Classification for Standards) categories: 91.100.60 - Thermal and sound insulating materials. The ICS classification helps identify the subject area and facilitates finding related standards.
EN 14307:2015 has the following relationships with other standards: It is inter standard links to EN 14307:2009+A1:2013, EN 14307:2015/prA1. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
EN 14307:2015 is associated with the following European legislation: EU Directives/Regulations: 305/2011; Standardization Mandates: M/103 REV. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
You can purchase EN 14307:2015 directly from iTeh Standards. The document is available in PDF format and is delivered instantly after payment. Add the standard to your cart and complete the secure checkout process. iTeh Standards is an authorized distributor of CEN standards.
以下は、英語の記事の要約です。 記事タイトル：EN 14307:2015 - ビル用機器および産業設備用断熱材 - 工場製造の発泡ポリスチレンフォーム（XPS）製品 - 仕様 記事内容：このヨーロッパ規格は、-180℃から+75℃程度の動作温度範囲で使用されるビル用機器および産業設備の断熱材として使用される工場製造の発泡ポリスチレンフォーム製品の要件を定めています。 -50℃未満の温度では、材料の適用性に関する特別なテスト（例：酸素の液化）が推奨されています。すべての場合において、製造業者のアドバイスに従うことが重要です。 製品は、表面が付いたまたは付いていないボード、パイプセクション、セグメント、およびプレファブリケートされた製品の形態で製造されます。 このヨーロッパ規格では、製品の特性について説明し、試験、適合性の評価、マーキング、およびラベリング手続きを含めています。 この規格によってカバーされる製品は、プレファブリケートされた断熱システムおよび複合パネルにも使用されますが、これらの製品を組み込んだシステムの性能はカバーされていません。 このヨーロッパ規格では、特定の応用において製品が目的に適合するために達成する必要がある特性の要求レベルを特定しません。特定の応用における要求レベルは、規制および入札案に明記されています。 10℃の平均温度で宣言された熱伝導率が0.060 W/(m·K)を超える製品は、この規格の対象外となります。 このヨーロッパ規格では、建物の構造物の断熱や音響断熱用の製品は対象としていません。
記事タイトル：EN 14307:2015 - 建築設備および産業設備用の断熱材 - 工場製造の発泡スチロール（XPS）製品 - 仕様 記事内容：このヨーロッパ標準は、約-180°Cから+75°Cの範囲で動作する建築設備および産業設備の断熱材として使用される工場製造の発泡スチロール製品の要件を指定しています。-50°C未満の動作温度では、材料の予定された用途に対する適合性に関する特別なテストが推奨されます（例：酸素の液化）。すべての場合において、製造業者のアドバイスに従う必要があります。 製品は、表面処理されたボード、非表面処理のボード、パイプセクション、セグメント、およびプレファブリケート製品の形態で製造されます。 このヨーロッパ標準では、製品の特性について説明し、試験、適合性評価、マーキング、ラベリングの手順を含みます。 この標準で対象とされる製品は、プレファブリケートされた断熱システムや複合パネルでも使用されますが、これらの製品を含むシステムの性能はカバーされていません。 このヨーロッパ標準では、特定の応用における製品の適合性を示すために必要な特性のレベルを具体的に規定していません。特定の応用に必要なレベルは、規制や入札要求に記載されています。 平均温度10°Cでの宣言された熱伝導率が0.060 W /（m·K）を超える製品には、この標準は適用されません。 また、このヨーロッパ標準では、建築構造物の断熱や音響断熱に使用される製品を対象としていません。
아래는 영어로 된 기사의 요약입니다. 기사 제목: EN 14307:2015 - 건물 설비 및 산업 설치용 열 절연제품 - 공장 제조 포스토렌 발포 폼(XPS) 제품 - 사양 기사 내용: 이 유럽 표준은 약 -180℃에서 +75℃까지의 운영 온도 범위를 가지는 건물 설비 및 산업 설치의 열 절연을 위해 사용되는 공장 제조 포스토렌 발포 폼 제품의 요구 사항을 규정합니다. -50℃ 이하의 온도에서는 재료의 적합성에 대한 특수시험(예: 산소 액화)이 권장됩니다. 모든 경우에 제조업체의 권고사항을 따르는 것이 좋습니다. 제품은 마감된 또는 마감되지 않은 보드, 파이프 부분, 세그먼트 및 사전 제작된 제품 형태로 제조됩니다. 이 유럽 표준은 제품 특성을 설명하며, 시험, 준수 평가, 표시 및 라벨링 절차를 포함합니다. 이 표준으로 규정된 제품은 또한 사전 제작된 열 절연 시스템과 복합 패널에 사용되며, 이러한 제품을 포함하는 시스템의 성능은 규정되지 않습니다. 이 유럽 표준은 특정 응용 분야에서 용도에 적합한 제품이 달성해야 하는 주어진 특성의 요구 수준을 규정하지 않습니다. 특정 응용을 위한 요구 수준은 규정과 입찰 초청에서 확인할 수 있습니다. 10℃ 평균 온도에서 선언된 열 전도율이 0.060 W/(m·K)보다 큰 제품은 이 표준에 해당하지 않습니다. 이 유럽 표준은 건물 구조물 절연 및 음향 절연용으로 사용되는 제품은 다루지 않습니다.
EN 14307:2015 is a European Standard that specifies the requirements for factory-made extruded polystyrene foam products used for thermal insulation in building equipment and industrial installations. These products are suitable for operating temperatures ranging from approximately -180 °C to +75 °C. Special tests are recommended for temperatures below -50 °C. The products come in various forms such as faced or unfaced boards, pipe sections, segments, and prefabricated ware. The standard describes product characteristics, testing procedures, evaluation of conformity, marking, and labeling. However, it does not specify the required level of a property for a specific application. The standard also excludes products with a declared thermal conductivity of greater than 0.060 W/(m·K) at a mean temperature of 10 °C. Additionally, it does not cover products used for building structure insulation or acoustical insulation.
제목: EN 14307:2015 - 건축 설비 및 산업 설치물을 위한 열 절연 제품 - 공장 제조된 발포 스티로폼 (XPS) 제품 - 사양 내용: 이 유럽 표준은 약 -180 °C에서 + 75 °C의 작동 온도 범위를 갖는 건축 설비 및 산업 설치물의 열 절연에 사용되는 공장 제조된 발포 스티로폼 제품에 대한 요구 사항을 정의합니다. -50 °C 이하의 작동 온도에서는 (산소 액화등과 같은) 지정된 용도에 대한 재료의 적합성에 대한 특수 시험을 권장합니다. 모든 경우에 제조업체의 조언은 따라야 합니다. 제품은 마감 된 또는 마감되지 않은 판, 파이프 섹션, 세그먼트 및 사전 제조된 제품의 형태로 제조됩니다. 이 유럽 표준은 제품 특성을 설명하고 시험, 준수 평가, 표시 및 표시 방법을 포함합니다. 이 표준으로 다루는 제품은 사전 제조된 열 절연 시스템과 복합 패널에도 사용됩니다. 그러나 이러한 제품을 포함한 시스템의 성능은 다루지 않습니다. 특정 응용 프로그램에서 제품의 적합성을 입증하기 위해 얻어야 하는 특정 속성 수준을 명시하지 않습니다. 주어진 응용 프로그램에 필요한 수준은 규정 및 입찰 초대에 찾을 수 있습니다. 평균 온도 10 °C에서 선언되는 열 전도율이 0.060 W / (m·K)보다 큰 제품은 이 표준의 적용 대상이 아닙니다. 이 유럽 표준은 건축 구조물 절연용이나 음향 절연용으로 사용되는 제품은 다루지 않습니다.
The article discusses the specifications for factory-made extruded polystyrene foam (XPS) products used for thermal insulation in building equipment and industrial installations. It states that these products should be suitable for operating temperatures ranging from -180 °C to +75 °C. Special tests are advised for temperatures below -50 °C. The products can be in the form of boards, pipe sections, segments, or prefabricated ware. The article describes the characteristics of these products and provides procedures for testing, conformity evaluation, marking, and labeling. It emphasizes that the performance of systems incorporating these products is not covered by this standard. The article also notes that the required level of a property for a specific application is not specified by this standard, and that regulations and invitations to tender should be consulted for the appropriate levels. Additionally, it states that products with a declared thermal conductivity greater than 0.060 W/(m·K) at a mean temperature of 10 °C are not covered. Lastly, the article clarifies that this standard does not include products for building insulation or acoustic insulation.
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...