iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 12023:1996

(Main)

Self-adhesive tapes - Measurement of water transmission in a warm humid atmosphere

Self-adhesive tapes - Measurement of water transmission in a warm humid atmosphere

This standard specifies the method to determine the mass of water vapour transmitted through the tape under specific test conditions. Details of the test method depend upon the width of the adhesive tape under test. For adhesive tapes less than 50 mm width it is necessary to use Annex A (normative).

Klebebänder - Messung der Wasserdampfdurchlässigkeit in feuchtwarmer Atmosphäre

Diese Norm legt das Verfahren zur Bestimmung der Masse des Wasserdampfes fest, die unter festgelegten Prüfbedingungen durch das Klebeband durchgelassen wird. Einzelheiten des Prüfverfahrens werden in Abhängigkeit von der Breite des untersuchten Klebebandes festgelegt. Für Klebebandbreiten unter 50 mm gilt der (normative) Anhang A.

Rubans auto-adhésifs - Mesure de la transmission de vapeur d'eau en atmosphère chaude et humide

La présente norme européenne prescrit une méthode pour déterminer la masse de vapeur d'eau transmise à travers un ruban adhésif dans des conditions d'essai spécifiées. Les détails de la méthode d'essai dépendent de la largeur de ruban adhésif soumis à l'essai. Pour des rubans adhésifs de largeur inférieure à 50 mm, il est nécessaire d'utiliser l'annexe A (normative).

Samolepilni trakovi - Merjenje prenosa vodne pare v topli vlažni atmosferi

General Information

Status
Withdrawn
Publication Date
20-Aug-1996
Withdrawal Date
09-Mar-2021
ICS
83.180 - Adhesives
Technical Committee
CEN/TC 193 - Adhesives
Drafting Committee
CEN/TC 193/WG 7 - Self adhesive tapes
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
10-Mar-2021
Ref Project
SIST EN 12023:1997 - Self-adhesive tapes - Measurement of water transmission in a warm humid atmosphere

Buy Standard

EN 12023:1997EN 12023:1997
PreviousNext
Standard
EN 12023:1997
English language
14 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Samolepilni trakovi - Merjenje prenosa vodne pare v topli vlažni atmosferiKlebebänder - Messung der Wasserdampfdurchlässigkeit in feuchtwarmer AtmosphäreRubans auto-adhésifs - Mesure de la transmission de vapeur d'eau en atmosphere chaude et humideSelf-adhesive tapes - Measurement of water transmission in a warm humid atmosphere83.180LepilaAdhesi
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 10364:2024(Main)
Structural adhesives - Determination of the pot life (working life) of multi-component adhesives (ISO 10364:2024)
SIST EN ISO 10364:2024

This document specifies methods for determining the pot life of multi-part adhesives, in order to be able to determine whether the pot life conforms to the minimum specified working life required of an adhesive.
The different methods described in this document to measure the property do not necessarily provide identical results.
The test methods described are suitable for assessing all multi–part adhesives, and especially epoxy based and polyurethane based adhesives, but they are not suitable for some acrylic-based adhesives.
NOTE 1       Some of the methods described in this document can also be suitable for determination of working life of one-part adhesives that react to humidity (e.g. PUR prepolymers).
NOTE 2       This document can also be used for assessing non-structural adhesives.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 21368:2023(Main)
Adhesives - Guidelines for the fabrication of adhesively bonded structures and reporting procedures suitable for the risk evaluation of such structures (ISO 21368:2022)
SIST EN ISO 21368:2023

This document provides guidelines describing the adhesive bonding quality requirements suitable for use by adhesive user-companies utilizing adhesive bonding as a means of fabrication. In particular, the guidelines define various approaches to meeting quality requirements for fabrication and reporting procedures, both in workshops and on site. These guidelines aim to convey the importance of maintaining quality standards in fabrication and reporting procedures, keeping records and thus enabling documentation to provide the basis for risk evaluation of adhesively bonded structures in service and in use.
These guidelines have been prepared such that:
a) they are independent of the type of adhesively bonded structure;
b) they are independent of adhesive user-companies’ and suppliers’ product recommendations;
c) they define the quality requirements for adhesive bonding in terms of fabrication and reporting procedures, both in workshops and on site;
d) they can be used as the basis for risk evaluation of adhesively bonded structures in service and in use;
e) they can be used as a basis for assessing a fabricator's capability to produce adhesively bonded structures fulfilling specified quality requirements when they are detailed in one or more of the following:
—    a contract between the parties involved;
—    an application standard;
—    a regulatory statement.
The guidelines contained within this document can be adopted in full or selectively chosen by the adhesive user to suit the structure concerned. The guidelines provide a flexible framework for the control of adhesive bonding activities in the following cases.
Case 1
The provision of specific requirements for adhesive bonding in contracts that require the adhesive user to have a quality system other than ISO 9001.
Case 2
The provision of specific requirements for adhesive bonding as guidance to an adhesive user developing a quality system.
Case 3
The provision of specific requirements for references in application standards that uses adhesive bonding as part of its requirements or in a contract between relevant parties.
Case 4
The provision of a framework for fabrication and reporting procedures to a quality standard, suitable in particular as a basis for the risk evaluation of adhesively bonded structures.

  • Standard
    111 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    108 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 6076:2023(Main)
Adhesives - Installation of floor coverings, wood flooring, levelling compounds and tiles - Specification of trowel notch sizes (ISO 6076:2023, Corrected version 2023-09)
SIST EN ISO 6076:2023

This document specifies the individual measurements of notches. It assigns specific codes used to label notched tools according to the measurements and tolerances specified in this document.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 302-8:2023(Main)
Adhesives for load-bearing timber structures - Test methods - Part 8: Static load test of multiple bond line specimens in compression shear
SIST EN 302-8:2023

This document specifies a method of determining the ability of adhesive bonds to resist static load. It is applicable to adhesives used in load bearing timber structures.
It is applicable for the following applications:
a) for assessing the compliance of adhesives according to EN 301, EN 15425, EN 16254, EN 17334 and EN 17418;
b) for assessing the suitability and quality of adhesives for load-bearing timber structures;
c) for assessing the effect on the bond strength resulting from constant load at different climate conditions.
This method is intended primarily to obtain performance data for the classification of adhesives for load bearing timber structures according to their suitability for use in defined climatic environments.
This method is not intended to provide data for structural design and does not necessarily represent the performance of the bonded member in service.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 302-5:2023(Main)
Adhesives for load-bearing timber structures - Test methods - Part 5: Determination of maximum assembly time under referenced conditions
SIST EN 302-5:2023

This document specifies a laboratory method of determining the maximum assembly time at two spread rate levels in standard atmosphere [20/65].
This document is applicable to obtaining a reliable base of comparison of the maximum assembly time between adhesives at referenced conditions.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 302-4:2023(Main)
Adhesives for load-bearing timber structures - Test methods - Part 4: Determination of the effects of wood shrinkage on the shear strength
SIST EN 302-4:2023

This document specifies a method for determining the influence of shear strength in crosswise gluing by wood shrinkage under drying conditions.
It is applicable for the following applications:
a)   for assessing the compliance of adhesives with EN 301, EN 15425, EN 16254, EN 17334 and EN 17418;
b)   for assessing the suitability and quality of adhesives for load-bearing timber structures;
c)   for determining if the adhesive is capable of withstanding stresses due to wood shrinkage without unacceptable loss of strength.
This test is intended primarily to obtain performance data for the classification of adhesives for load-bearing timber structures according to their suitability for use in defined climatic environments. This test is carried out on Norway spruce (Picea abies L.).
This method is not intended to provide data for structural design and does not necessarily represent the performance of the bonded member in service.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 302-7:2023(Main)
Adhesives for load-bearing timber structures - Test methods - Part 7: Determination of the working life under referenced conditions
SIST EN 302-7:2023

This document specifies a method for determining the working life for adhesives mixed with hardener for load-bearing timber structures, by a viscosity test.
This method does not apply to determining the working life of a multi-component adhesive whose actual working life is very short.
This document is only intended for obtaining a reliable basis for comparison between adhesives. The method gives results which cannot be applied to the safe manufacture of timber structures without modifications for the influences of factory temperature and relative air humidity.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15425:2023(Main)
Adhesives - One component polyurethane (PUR) for load-bearing timber structures - Classification and performance requirements
SIST EN 15425:2023

This document establishes a classification for one component polyurethane (PUR) adhesives according to their suitability for use in load-bearing timber products in defined climatic exposure conditions, and specifies performance requirements for such adhesives for the factory manufacture or factory-like manufacturing of load-bearing timber products only.
It also classifies “adhesive product lines” where all the products within the line have the same chemical composition except for a different amount of catalyst.
This document only specifies the performance of adhesives for use in an environment corresponding to the defined conditions.
The performance requirements of this document are applicable to the adhesives only, not to the manufactured timber products. This document does not cover the performance of adhesives for on-site gluing (except for factory-like conditions) or the production of wood-based panels, except solid wood panels, or modified and stabilized wood with considerably reduced swelling and shrinkage properties, e.g. acetylated wood, heat treated wood and polymer impregnated wood.
This document is primarily intended for use by adhesive manufacturers and for use in timber products bonded with adhesives, to assess or control the quality of adhesives. The requirements are applicable to the type testing of the adhesives. Production control activities are outside the scope of this document.
Adhesives meeting the requirements of this document are adequate for use in load-bearing timber products, provided that the bonding process has been carried out according to an appropriate product standard.
This document does not address the classification and use of adhesives in combination with the spraying of water before or during the bonding process; see informative Annex C of this document.
This does neither allow nor forbid the use of adhesives in combination with the spraying of water.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 302-2:2023(Main)
Adhesives for load-bearing timber structures - Test methods - Part 2: Determination of resistance to delamination
SIST EN 302-2:2023

This document specifies a method for determining the resistance to delamination in glue lines.
It is applicable to the following applications:
a)   for assessing the compliance of adhesives with EN 301, EN 15425, EN 16254, EN 17334 and EN 17418;
b)   for assessing the suitability and quality of adhesives for load-bearing timber structures;
c)   for comparing the effects on the bond strength resulting from the choice of bonding conditions, from different climatic conditioning and from the treatment of the test pieces before and after bonding.
This test does not apply to modified and stabilized wood with strongly reduced swelling and shrinkage properties, such as acetylated wood, heat-treated wood and polymer impregnated wood.
This test is intended primarily to obtain performance data for the classification of adhesives for load-bearing timber structures according to their suitability for use in defined climatic environments.
This method is not intended to provide data for structural design and does not necessarily represent the performance of the bonded member in service.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 302-6:2023(Main)
Adhesives for load-bearing timber structures - Test methods - Part 6: Determination of the minimum pressing time under referenced conditions
SIST EN 302-6:2023

This document specifies a method of determining the minimum pressing time for two glue line thicknesses, close contact glue line and thick glue line (between 0,3 mm and 8 mm), at three temperatures. It is applicable to adhesives used in load-bearing timber products.
This document is only intended for obtaining a reliable base of comparison of pressing time between adhesives. The method gives results that cannot be applied to the safe manufacture of timber structures without modifications for the influences of timber density/absorbency, moisture content, factory temperature and relative air humidity.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day