EN 2731:2005

Aerospace series - Magnesium alloy MG-C46001 - T6 - Sand casting

This standard specifies the requirements relating to:
Magnesium alloy MG-C46001
T6
Sand casting
for aerospace application.

Luft- und Raumfahrt - Magnesiumlegierung MG-C46001 - T6 - Sandgussstück

Diese Norm legt die Anforderungen an
Magnesiumlegierung MG-C46001-
T6
Sandgussstück
für Anwendungen in der Luft- und Raumfahrt fest.

Série aérospatiale - Alliage de magnésium MG-C46001 - T6 - Produit coulé en sable

Aerospace series - Magnesium alloy MG-C46001 - T6 - Sand casting

General Information

• Status: Published
• Publication Date: 23-Aug-2005
• Withdrawal Date: 27-Feb-2006
• ICS: 49.025.15 - Non-ferrous alloys in general
• Technical Committee: ASD-STAN - Aerospace
• Drafting Committee: ASD-STAN/D 4 - Metallic
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 24-Aug-2005
• Completion Date: 24-Aug-2005
• Ref Project: SIST EN 2731:2005 - Aerospace series - Magnesium alloy MG-C46001 - T6 - Sand casting

Standards Content (Sample)

SLOVENSKI STANDARD
01-december-2005
Aerospace series - Magnesium alloy MG-C46001 - T6 - Sand casting
Aerospace series - Magnesium alloy MG-C46001 - T6 - Sand casting
Luft- und Raumfahrt - Magnesiumlegierung MG-C46001 - T6 - Sandgussstück
Série aérospatiale - Alliage de magnésium MG-C46001 - T6 - Produit coulé en sable
Ta slovenski standard je istoveten z: EN 2731:2005
ICS:
49.025.15 Neželezove zlitine na Non-ferrous alloys in general
splošno
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 2731
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2005
ICS 49.025.15
English Version
Aerospace series - Magnesium alloy MG-C46001 - T6 - Sand
casting
Série aérospatiale - Alliage de magnésium MG-C46001 - Luft- und Raumfahrt - Magnesiumlegierung MG-C46001 -
T6 - Produit coulé en sable T6 - Sandgußstück
This European Standard was approved by CEN on 22 April 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 2731:2005: E
worldwide for CEN national Members.

Contents
Foreword .3
Introduction.4
1 Scope .4
2 Normative references .4

Foreword
This document (EN 2731:2005) has been prepared by the European Association of Aerospace
Manufacturers - Standardization (AECMA-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this Standard has
received the approval of the National Associations and the Official Services of the member countries of
AECMA, prior to its presentation to CEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by February 2006, and conflicting national standards shall be withdrawn
at the latest by February 2006.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Ice
...