EN ISO 7623:2015

Steel cord conveyor belts - Cord-to-coating bond test - Initial test and after thermal treatment (ISO 7623:2015)

ISO 7623:2015 specifies a method for determining the bond strength of metal cords to their surrounding coating, either in the initial state or after thermal treatment.
It applies exclusively to metal-carcass conveyor belts.

Stahlseil-Fördergurte - Haftung zwischen den Seilen und der Kernschicht - Prüfung im Anlieferungszustand und nach thermischer Behandlung (ISO 7623:2015)

Courroies transporteuses à câbles d'acier - Adhérence des câbles dans l'enrobage - Essais à l'état original et après traitement thermique (ISO 7623:2015)

ISO 7623:2015 spécifie une méthode pour la détermination de l´adhérence des câbles métalliques dans l´enrobage soit à l´état original, soit après traitement thermique.
Elle est applicable exclusivement aux courroies transporteuses à câbles d´acier.

Naprave za kontinuirni transport - Trakovi tračnih transporterjev z jeklenim vložkom - Sprijemnost med vložkom in prevleko - Preskus novega traku in traku po toplotni obdelavi (ISO 7623:2015)

Ta mednarodni standard določa metodo za določanje moči sprijema kovinskih vložkov z njihovimi prevlekami, in sicer v prvotnem stanju ali po toplotni obdelavi. Uporablja se izključno za trakove tračnih transporterjev s kovinskim trupom.

General Information

• Status: Withdrawn
• Publication Date: 10-Nov-2015
• Withdrawal Date: 22-Nov-2022
• ICS: 53.040.20 - Components for conveyors
• Technical Committee: CEN/TC 188 - Conveyor belts
• Drafting Committee: CEN/TC 188/WG 1 - Technical test methods
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 23-Nov-2022
• Ref Project: SIST EN ISO 7623:2016 - Steel cord conveyor belts - Cord-to-coating bond test - Initial test and after thermal treatment (ISO 7623:2015)

Relations

• Replaces: EN ISO 7623:1997 - Steel cord conveyor belts - Cord-to-coating bond test - Initial test and after thermal treatment (ISO 7623:1996)
• Effective Date: 18-Nov-2015
• Replaced By: EN ISO 7623:2022 - Steel cord conveyor belts - Cord-to-coating bond test - Initial test and after thermal treatment (ISO 7623:2022)
• Effective Date: 15-Dec-2021

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 7623:2016
01-februar-2016
1DGRPHãþD
SIST EN ISO 7623:2001
1DSUDYH]DNRQWLQXLUQLWUDQVSRUW7UDNRYLWUDþQLKWUDQVSRUWHUMHY]MHNOHQLP
YORåNRP6SULMHPQRVWPHGYORåNRPLQSUHYOHNR3UHVNXVQRYHJDWUDNXLQWUDNX
SRWRSORWQLREGHODYL,62
Steel cord conveyor belts - Cord-to-coating bond test - Initial test and after thermal
treatment (ISO 7623:2015)
Stahlseil-Fördergurte - Haftung zwischen den Seilen und Kernschicht - Prüfung im
Anlieferzustand und nach thermischer Behandlung (ISO 7623:2015)
Courroies transporteuses à câbles d'acier - Adhérence des câbles dans l'enrobage -
Essais à l'état original et après traitement thermique (ISO 7623:2015)
Ta slovenski standard je istoveten z: EN ISO 7623:2015
ICS:
53.040.20 Deli za transporterje Components for conveyors
SIST EN ISO 7623:2016 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 7623:2016

---------------------- Page: 2 ----------------------

SIST EN ISO 7623:2016


EN ISO 7623
EUROPEAN STANDARD

NORME EUROPÉENNE

November 2015
EUROPÄISCHE NORM
ICS 53.040.20 Supersedes EN ISO 7623:1997
English Version

Steel cord conveyor belts - Cord-to-coating bond test -
Initial test and after thermal treatment (ISO 7623:2015)
Courroies transporteuses à câbles d'acier - Adhérence Stahlseil-Fördergurte - Haftung zwischen den Seilen
des câbles dans l'enrobage - Essais à l'état original et und Kernschicht - Prüfung im Anlieferzustand und
après traitement thermique (ISO 7623:2015) nach thermischer Behandlung (ISO 7623:2015)
This European Standard was approved by CEN on 26 September 2015.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 7623:2015 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 7623:2016
EN ISO 7623:2015 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 7623:2016
EN ISO 7623:2015 (E)
European foreword
This document (EN ISO 7623:2015) has been prepared by Technical Committee ISO/TC 41 "Pulleys and
belts (including veebelts)" in collaboration with Technical Committee CEN/TC 188 “Conveyor belts” the
secretariat of which is held by SNV.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2016, and conflicting national standards shall be
withdrawn at the latest by May 2016.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN ISO 7623:1997.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 7623:2015 has been approved by CEN as EN ISO 7623:2015 without any modification.
3

---------------------- P
...