EN ISO 15877-3:2009
(Main)Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 3: Fittings (ISO 15877-3:2009)
Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 3: Fittings (ISO 15877-3:2009)
ISO 15877-3:2009 specifies the characteristics of fittings made from chlorinated poly(vinyl chloride) (PVC-C) for piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems) and for heating systems under design pressures and temperatures according to the class of application.
ISO 15877-3:2009 covers a range of service conditions (application classes) and design pressure classes. It does not apply if the values of the design temperature, maximum design temperature and malfunction temperature are in excess of those given in ISO 15877-1:2009. ISO 15877-3:2009 also specifies the parameters for the test methods to which it refers.
In conjunction with the other parts of ISO 15877, it is applicable to PVC-C fittings, their joints and joints with components of PVC-C, other plastics and non-plastics materials intended to be used for hot and cold water installations.
It is applicable to fittings of the following types:
fittings for solvent cement joints;
mechanical fittings;
fittings with incorporated inserts.
Kunststoff-Rohrleitungssysteme für die Warm- und Kaltwasserinstallation - Chloriertes Polyvinylchlorid (PVC-C) - Teil 3: Formstücke (ISO 15877-3:2009)
Dieser Teil von ISO 15877 legt Anforderungen an Formstücke aus chloriertem Polyvinylchlorid (PVC C) für Rohrleitungssysteme fest, die in der Warm und Kaltwasserinstallation innerhalb von Gebäuden für den Transport von Trink oder Brauchwasser (Hausinstallation) und in Heizungsanlagen unter Berücksichtigung des betreffenden zulässigen Betriebsdruckes und der für die jeweilige Anwendungsklasse geltenden Temperaturen (siehe ISO 15877 1:2008, Tabelle 1 von ISO 15877 1:2008) eingesetzt werden.
Dieser Teil von ISO 15877 enthält Festlegungen zu Anwendungsklassen, die sich auf Betriebsbedingungen beziehen, sowie Festlegungen über zulässige Betriebsdrücke. Dieser Teil von ISO 15877 gilt nicht, wenn für TD, Tmax und Tmal höhere als die in Tabelle 1 von ISO 15877 1:2008, Tabelle 1, aufgeführten Werte zu Grunde gelegt werden.
ANMERKUNG 1 Der Anwender bzw. Auftraggeber ist unter Berücksichtigung der eigenen Anforderungen sowie der geltenden nationalen Festlegungen und Verlegepraktiken für die entsprechende Auswahl dieser Kriterien verantwortlich.
Sie legt auch die Prüfparameter für die Prüfverfahren fest, auf die in diesem Teil von ISO 15877 verwiesen wird.
Zusammen mit den übrigen Teilen von ISO 15877 gilt dieser Teil für Formstücke aus PVC C, deren Verbindungen untereinander sowie mit anderen Rohrleitungsteilen aus PVC C, anderen Kunststoffen oder metallenen Werkstoffen, die für die Warm und Kaltwasserinstallation vorgesehen sind.
Dieser Teil von ISO 15877 gilt für die folgenden Arten von Formstücken:
Formstücke für Klebverbindungen;
mechanische Rohrverbinder;
Formstücke mit integrierten Einsätzen.
ANMERKUNG 2 Formstücke aus PVC C werden im Spritzgießverfahren hergestellt.
Systèmes de canalisations en plastique pour les installations d'eau chaude et froide - Poly(chlorure de vinyle) chloré (PVC-C) - Partie 3: Raccords (ISO 15877-3:2009)
L'ISO 15877-3:2009 spécifie les caractéristiques des raccords en poly(chlorure de vinyle) chloré (PVC-C) pour les systèmes de canalisations destinés aux installations d'eau chaude et froide à l'intérieur des bâtiments pour le transport de l'eau, destinée ou non à la consommation humaine (systèmes domestiques) et aux systèmes de chauffage, à des pressions et à des températures de service correspondant à la classe d'application.
L'ISO 15877-3:2009 couvre une gamme de conditions de service (classes d'application) et de pression de service. Elle ne s'applique pas si les valeurs de la température de service, de la température maximale de service et de la température de dysfonctionnement sont supérieures à celles qui sont données dans l'ISO 15877-1:2009. L'ISO 15877-3:2009 spécifie également les paramètres d'essai pour les méthodes d'essai auxquelles elle fait référence.
Conjointement avec les autres parties de l'ISO 15877, l'ISO 15877-3:2009 s'applique aux raccords en PVC-C, à leurs assemblages et aux assemblages avec des composants faits en PVC-C ou en d'autres matériaux, plastiques ou non plastiques, pouvant être utilisés pour des installations d'eau chaude et froide.
Elle s'applique aux raccords répondant aux types suivants:
raccords pour assemblages collés au solvant;
raccords mécaniques;
raccords avec inserts incorporés.
Cevni sistemi iz polimernih materialov za napeljave z vročo in hladno vodo - Klorirani polivinilklorid (PVC-C) - 3. del: Fitingi (ISO 15877-3:2009)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-junij-2009
1DGRPHãþD
SIST EN ISO 15877-3:2004
&HYQLVLVWHPLL]SROLPHUQLKPDWHULDORY]DQDSHOMDYH]YURþRLQKODGQRYRGR
.ORULUDQLSROLYLQLONORULG 39&& GHO )LWLQJL ,62
Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl
chloride) (PVC-C) - Part 3: Fittings (ISO 15877-3:2009)
Kunststoff-Rohrleitungssysteme für die Warm- und Kaltwasserinstallation - Chloriertes
Polyvinylchlorid (PVC-C) - Teil 3: Formstücke (ISO 15877-3:2009)
Systemes de canalisations en plastique pour les installations d'eau chaude et froide -
Poly(chlorure de vinyle) chloré (PVC-C) - Partie 3: Raccords (ISO 15877-3:2009)
Ta slovenski standard je istoveten z: EN ISO 15877-3:2009
ICS:
23.040.45 Fitingi iz polimernih Plastics fittings
materialov
91.140.60 Sistemi za oskrbo z vodo Water supply systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 15877-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2009
ICS 23.040.45; 91.140.60 Supersedes EN ISO 15877-3:2003
English Version
Plastics piping systems for hot and cold water installations -
Chlorinated poly(vinyl chloride) (PVC-C) - Part 3: Fittings (ISO
15877-3:2009)
Systèmes de canalisations en plastique pour les Kunststoff-Rohrleitungssysteme für die Warm- und
installations d'eau chaude et froide - Poly(chlorure de Kaltwasserinstallation - Chloriertes Polyvinylchlorid (PVC-
vinyle) chloré (PVC-C) - Partie 3: Raccords (ISO 15877- C) - Teil 3: Formstücke (ISO 15877-3:2009)
3:2009)
This European Standard was approved by CEN on 28 February 2009.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15877-3:2009: E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
This document (EN ISO 15877-3:2009) has been prepared by Technical Committee CEN/TC 155 "Plastics
piping systems and ducting systems", the secretariat of which is held by NEN, in collaboration with Technical
Committee ISO/TC 138 "Plastics pipes, fittings and valves for the transport of fluids".
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by September 2009, and conflicting national standards shall be
withdrawn at the latest by September 2009.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 15877-3:2003.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
INTERNATIONAL ISO
STANDARD 15877-3
Second edition
2009-03-15
Plastics piping systems for hot and cold
water installations — Chlorinated
poly(vinyl chloride) (PVC-C) —
Part 3:
Fittings
Systèmes de canalisations en plastique pour les installations d’eau
chaude et froide — Poly(chlorure de vinyle) chloré (PVC-C) —
Partie 3: Raccords
Reference number
ISO 15877-3:2009(E)
©
ISO 2009
ISO 15877-3:2009(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2009
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2009 – All rights reserved
ISO 15877-3:2009(E)
Contents Page
Foreword. iv
Introduction . vi
1 Scope . 1
2 Normative references . 1
3 Terms, definitions and symbols. 2
3.1 Terms and definitions. 2
3.2 Symbols . 3
4 Material characteristics. 3
4.1 General. 3
4.2 Fitting material . 3
4.3 Evaluation of σ -values . 3
LPL
4.4 Thermal stability . 7
4.5 Metallic material . 8
4.6 Influence on water intended for human consumption. 9
5 General characteristics . 9
5.1 Appearance . 9
5.2 Opacity. 9
6 Geometrical characteristics. 9
6.1 General. 9
6.2 Dimensions of fittings . 9
6.3 Dimensions of sockets. 16
6.4 Dimensions of flange adaptors and flanges . 18
6.5 Dimensions of metallic fittings. 20
7 Mechanical characteristics . 20
7.1 Resistance to internal pressure . 20
7.2 Determination of free lengths. 21
7.3 Derivation of the hydrostatic test pressure .22
8 Performance requirements . 23
9 Adhesives . 23
10 Sealing rings . 23
11 Marking . 24
11.1 General. 24
11.2 Minimum required marking. 24
11.3 Additional marking . 24
Bibliography . 25
ISO 15877-3:2009(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 15877-3 was prepared by the European Committee for Standardization (CEN) Technical Committee
CEN/TC 155, Plastics piping systems and ducting systems, in collaboration with ISO Technical Committee
ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 2, Plastics pipes
and fittings for water supplies, in accordance with the Agreement on technical cooperation between ISO and
CEN (Vienna Agreement).
This part of ISO 15877 is part of a System Standard for plastics piping systems of a particular material for a
specified application. There are a number of such System Standards.
The System Standards are consistent with general standards on functional requirements and recommended
practices for installation.
This second edition cancels and replaces the first edition (ISO 15877-3:2003).
1)
ISO 15877 consists of the following parts , under the general title Plastics piping systems for hot and cold
water installations — Chlorinated poly(vinyl chloride) (PVC-C):
⎯ Part 1: General
⎯ Part 2: Pipes
⎯ Part 3: Fitt
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.