EN 12012-2:2001/A1:2003
(Amendment)Rubber and plastics machines - Size reduction machines - Part 2: Safety requirements for strand pelletisers
Rubber and plastics machines - Size reduction machines - Part 2: Safety requirements for strand pelletisers
This standard specifies the essential safety requirements applicable to the design and construction of strand pelletisers used for plastics and rubber and fed continuously by an extruder or a reactor.
The machine begins with the feed opening of the feeding device, or start-up devices if fitted, and ends with the discharge area.
Only the significant hazards listed in clause 4 and dealt with in clause 5 are subject to this standard.
NOTE Directive 94/9/EC concerning equipment and protective systems intended for use in potentially explosive atmospheres can be applicable to the type of machine or equipment covered by this European Standard. The present standard is not intended to provide means of complying with the essential health and safety requirements of Directive 94/9/EC.
This standard applies to machines which are manufactured after the date of approval of this standard by CEN."
Gummi- und Kunststoffmaschinen - Zerkleinerungsmaschinen - Teil 2: Sicherheitsanforderungen für Stranggranulatoren
Diese Norm behandelt die wesentlichen Sicherheitsanforderungen, die bei Konzipierung und Bau von kontinuierlich von einem Extruder oder einem Reaktor beschickten Stranggranulatoren für Gummi und Kunststoffe anzuwenden sind.
Die Maschine beginnt mit der Beschickungseinrichtung oder, falls damit ausgerüstet, mit der Anfahreinrichtung und endet mit dem Entnahmebereich.
Nur die in Abschnitt 4 angegebenen und in Abschnitt 5 behandelten signifikanten Gefährdungen sind Gegenstand dieser Norm.
ANMERKUNG Die Richtlinie 94/9/EG bezüglich Geräte und Schutzsysteme zur bestimmungsgemäßen Verwendung in explosionsgefährdeten Bereichen kann bei Maschinen oder Bauteilen nach dieser Europäischen Norm zur Anwendung kommen. Es kann nicht davon ausgegangen werden, dass die vorliegende Norm mit der Richtlinie 94/9/EG in Übereinstimmung ist. Zur Erfüllung der Richtlinie 94/9/EG können zusätzliche Sicherheitsanforderungen in einer zukünftigen Ausgabe dieser Norm erforderlich sein.
Diese Norm gilt für Maschinen, die nach dem Annahmedatum der Norm durch CEN hergestellt worden sind.
Machines pour le caoutchouc et les matières plastiques - Machines à fragmenter - Partie 2: Prescriptions de sécurité relatives aux granulateurs à joncs
La présente norme spécifie les exigences essentielles de sécurité relatives à la conception et à la construction des granulateurs à joncs utilisés pour les matières plastiques et le caoutchouc et alimenté en continu par une extrudeuse ou un réacteur.
La machine commence à l'ouverture du dispositif d'alimentation ou au dispositif de démarrage s'il existe et se termine à la zone de déchargement.
Seuls les phénomènes dangereux significatifs énumérés à l'Article 4 et traités à l'Article 5 sont couverts par la présente norme.
NOTE La Directive 94/9/CE relative aux appareils et systèmes de protection destinés à être utilisés en atmosphères explosibles peut être appliquée au type de machine ou équipement couvert par la présente Norme européenne. La présente norme n'est pas destinée à fournir un moyen de satisfaire aux exigences essentielles de Santé et de Sécurité de la Directive 94/9/CE.
Ce document n'est pas applicable aux granulateurs à joncs qui ont été fabriqués avant la date de publication de la présente norme par le CEN."
Stroji za predelavo gume in plastike - Drobilni stroji - 2. del: Varnostne zahteve za iztiskovalne granulatorje
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 12012-2:2002/A1:2004
01-september-2004
Stroji za predelavo gume in plastike - Drobilni stroji - 2. del: Varnostne zahteve za
iztiskovalne granulatorje
Rubber and plastics machines - Size reduction machines - Part 2: Safety requirements
for strand pelletisers
Gummi- und Kunststoffmaschinen - Zerkleinerungsmaschinen - Teil 2:
Sicherheitsanforderungen für Stranggranulatoren
Machines pour le caoutchouc et les matieres plastiques - Machines a fragmenter - Partie
2: Prescriptions de sécurité relatives aux granulateurs a joncs
Ta slovenski standard je istoveten z: EN 12012-2:2001/A1:2003
ICS:
83.200 Oprema za gumarsko Equipment for the rubber and
industrijo in industrijo plastics industries
polimernih materialov
SIST EN 12012-2:2002/A1:2004 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
EN 12012-2:2001/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2003
ICS 83.200
English version
Rubber and plastics machines - Size reduction machines - Part
2: Safety requirements for strand pelletisers
Machines pour le caoutchouc et les matières plastiques - Gummi- und Kunststoffmaschinen -
Machines à fragmenter - Partie 2: Prescriptions de sécurité Zerkleinerungsmaschinen - Teil 2:
relatives aux granulateurs à joncs Sicherheitsanforderungen für Stranggranulatoren
This amendment A1 modifies the European Standard EN 12012-2:2001; it was approved by CEN on 14 November 2003.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the Management Centre or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2003 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12012-2:2001/A1:2003 E
worldwide for CEN national Members.
---------------------- Page: 2 ----------------------
EN 12012-2:2001/A1:2003 (E)
Foreword
This document (EN 12012-2:2001/prA1:2003) has been prepared by Technical Committee CEN/TC 145
"Rubber and plastics machines - Safety", the secretariat of which is held by UNI.
This Amendment to the European Standard EN 12012-2:2001 shall be given the status of a national
standard, either by publication of an identical text or by endorsement, at the latest by June 2004, and
conflicting national standards shall be withdrawn at the latest by June 2004.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands,
Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and the United Kingdom.
2
---------------------- Page: 3 ----------------------
EN 12012-2:2001/A1:2003 (E)
In clause 1, replace the text by the following one :
”1 Scope
This standard specifies the essential safety requirements applicable to the design and construction of strand
pelletisers used for plastics and rubber and fed continuousl
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.