Plastics and rubber machines - Injection moulding machines - Safety requirements (ISO 20430:2020)

This document specifies the essential safety requirements for the design and construction of injection moulding machines for the processing of plastics and/or rubber and provides information for their safe use.
This document is applicable only to injection moulding machines with hydraulic and/or electrical drives for platen movement.
This document deals with all significant hazards, hazardous situations and events relevant to injection moulding machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Annex A) during the life cycle of the machinery (see ISO 12100:2010, 5.4).
The following are not covered:
—     machines on which the clamping unit can only be operated by the physical force of the operator;
—     machines for which the hydraulic jack can only be manually operated;
—     injection blow moulding machines;
—     machines for reaction injection moulding;
—     compression moulding machines and transfer moulding machines;
—     direct-on sole moulding machines, unit sole and footwear component moulding machines, full shoe and boot moulding machines;
—     design of an exhaust system;
—     design and construction of the mould.
NOTE    Moulds and exhaust systems are not part of the machinery.
This document is not applicable to injection moulding machines which are manufactured before the date of its publication.

Kunststoff- und Gummimaschinen - Spritzgießmaschinen - Sicherheitsanforderungen (ISO 20430:2020)

Dieses Dokument legt die wesentlichen Sicherheitsanforderungen für die Konstruktion und den Bau von Spritzgießmaschinen für die Verarbeitung von Kunststoff und/oder Gummi fest und enthält Informationen für deren sichere Verwendung.
Dieses Dokument gilt nur für Spritzgießmaschinen mit hydraulischen und/oder elektrischen Antrieben für die Bewegung der Aufspannplatte.
Dieses Dokument behandelt alle signifikanten Gefährdungen, Gefährdungssituationen oder Gefährdungsereignisse, die auf Spritzgießmaschinen zutreffen, wenn sie bestimmungsgemäß und unter Bedingungen der missbräuchlichen Verwendung, die vom Hersteller während des Lebenszyklus der Maschine (siehe ISO 12100:2010, 5.4) vernünftigerweise vorhersehbar sind, verwendet werden (siehe Anhang A).
Folgende sind nicht erfasst:
—   Maschinen, bei denen die Schließeinheit nur durch die körperliche Kraft der Bedienperson betrieben werden kann;
—   Maschinen, bei denen die hydraulische Hubeinrichtung nur manuell bedient werden kann;
—   Spritzblasformmaschinen;
—   Maschinen für das Reaktionsgießen;
—   Formpressen und Spritzpressen;
—   Direktansohlmaschinen, Sohlen- und Schuhteileformmaschinen, Schuh- und Stiefelformmaschinen;
—   Konstruktion eines Absaugsystems;
—   Konstruktion und Bau des Werkzeugs.
ANMERKUNG   Werkzeuge und Absaugsysteme sind nicht Teil der Maschine.
Dieses Dokument gilt nicht für Spritzgießmaschinen, die vor dem Datum ihrer Veröffentlichung hergestellt wurden.

Machines pour les matières plastiques et le caoutchouc - Machines de moulage par injection - Prescription de sécurité (ISO 20430:2020)

Le présent document spécifie les exigences essentielles de sécurité applicables à la conception et à la construction des machines de moulage par injection qui sont utilisées pour le moulage des matières plastiques et/ou du caoutchouc et fournit des informations pour leur utilisation en toute sécurité.
Le présent document s'applique uniquement aux machines de moulage par injection à actionneurs hydrauliques et/ou électriques pour les mouvements du plateau.
Le présent document traite de tous les phénomènes dangereux, situations dangereuses et événements dangereux significatifs applicables aux machines de moulage par injection, dans le cadre d'une utilisation normale ou d'un mauvais usage raisonnablement prévisible par le fabricant (voir Annexe A) pendant leur cycle de vie (voir ISO 12100:2010, 5.4).
Les machines et éléments suivants sont exclus:
—          machines dont l'unité de fermeture ne peut être actionnée que par la force de l'opérateur;
—          machines dont le vérin hydraulique ne peut être actionné que manuellement;
—          machines de moulage par injection-soufflage;
—          machines de moulage par injection et réaction;
—          machines de moulage par compression et machines de moulage par transfert;
—          machines de moulage direct de semelles, machines de moulage de semelles et de composants d'articles chaussants, machines de moulage de chaussures et bottes complètes;
—          conception d'un système d'aspiration;
—          conception et construction du moule.
NOTE       Les moules et systèmes d'évacuation ne font pas partie des machines.
Le présent document ne s'applique pas aux machines de moulage par injection fabriquées avant sa date de publication.

Stroji za predelavo gume in plastike - Stroji za brizgalno vlivanje - Varnostne zahteve (ISO 20430:2020)

General Information

Status
Published
Publication Date
30-Jun-2020
Withdrawal Date
30-Jul-2022
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
01-Jul-2020
Due Date
25-Aug-2017
Completion Date
01-Jul-2020

Relations

Buy Standard

Standard
EN ISO 20430:2021 - BARVE
English language
161 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN ISO 20430:2017 - BARVE
English language
161 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 20430:2021
01-februar-2021
Nadomešča:
SIST EN 201:2009
Stroji za predelavo gume in plastike - Stroji za brizgalno vlivanje - Varnostne
zahteve (ISO 20430:2020)
Plastics and rubber machines - Injection moulding machines - Safety requirements (ISO
20430:2020)
Kunststoff- und Gummimaschinen - Spritzgießmaschinen - Sicherheitsanforderungen
(ISO 20430:2020)
Machines pour les matières plastiques et le caoutchouc - Machines de moulage par
injection - Prescription de sécurité (ISO 20430:2020)
Ta slovenski standard je istoveten z: EN ISO 20430:2020
ICS:
83.200 Oprema za gumarsko Equipment for the rubber and
industrijo in industrijo plastics industries
polimernih materialov
SIST EN ISO 20430:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 20430:2021

---------------------- Page: 2 ----------------------
SIST EN ISO 20430:2021


EN ISO 20430
EUROPEAN STANDARD

NORME EUROPÉENNE

July 2020
EUROPÄISCHE NORM
ICS 83.200 Supersedes EN 201:2009
English Version

Plastics and rubber machines - Injection moulding
machines - Safety requirements (ISO 20430:2020)
Machines pour les matières plastiques et le caoutchouc Kunststoff- und Gummimaschinen -
- Machines de moulage par injection - Prescription de Spritzgießmaschinen - Sicherheitsanforderungen (ISO
sécurité (ISO 20430:2020) 20430:2020)
This European Standard was approved by CEN on 26 April 2020.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 20430:2020 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 20430:2021
EN ISO 20430:2020 (E)
Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive 2006/42/EC aimed to be covered . 5

2

---------------------- Page: 4 ----------------------
SIST EN ISO 20430:2021
EN ISO 20430:2020 (E)
European foreword
This document (EN ISO 20430:2020) has been prepared by Technical Committee ISO/TC 270 "Plastics
and rubber machines" in collaboration with Technical Committee CEN/TC 145 “Plastics and rubber
machines” the secretariat of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by January 2021, and conflicting national standards shall
be withdrawn at the latest by July 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 201:2009.
Compared with EN 201:2009, the following significant technical changes have been made:
 modification of the scope;
 cancellation of the safety requirements for magnetic clamping systems;
 cancellation of the safety requirements for other ancillary requirements;
 adaption of the normative references and referring to ISO standards;
 consideration of revised type-A and type-B standards;
 moving of the list of significant hazards to an informative annex;
 modification of the safety requirements and protective measures by taking into consideration the
technological progress in the plastics and rubber industry and the continuous development of the
safety
...

SLOVENSKI STANDARD
oSIST prEN ISO 20430:2017
01-marec-2017
Stroji za predelavo gume in plastike - Stroji za brizgalno vlivanje - Varnostne
zahteve (ISO/DIS 20430:2017)
Plastics and rubber machines - Injection moulding machines - Safety requirements
(ISO/DIS 20430:2017)
Kunststoff- und Gummimaschinen - Spritzgießmaschinen - Sicherheitsanforderungen
(ISO/DIS 20430:2017)
Machines pour les matières plastiques et le caoutchouc - Machines de moulage par
injection - Prescription de sécurité (ISO/DIS 20430:2017)
Ta slovenski standard je istoveten z: prEN ISO 20430
ICS:
83.200 Oprema za gumarsko Equipment for the rubber and
industrijo in industrijo plastics industries
polimernih materialov
oSIST prEN ISO 20430:2017 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 20430:2017

---------------------- Page: 2 ----------------------
oSIST prEN ISO 20430:2017
DRAFT INTERNATIONAL STANDARD
ISO/DIS 20430
ISO/TC 270 Secretariat: UNI
Voting begins on: Voting terminates on:
2017-01-10 2017-04-03
Plastics and rubber machines — Injection moulding
machines — Safety requirements
Machines pour les matières plastiques et le caoutchouc — Machines de moulage par injection —
Prescription de sécurité
ICS: 83.200
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 20430:2017(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2017

---------------------- Page: 3 ----------------------
oSIST prEN ISO 20430:2017
ISO/DIS 20430:2017(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved

---------------------- Page: 4 ----------------------
oSIST prEN ISO 20430:2017
ISO/DIS 20430:2017(E)
Contents Page
Foreword . viii
Introduction . viii
1 Scope. x
2 Normative references . x
3 Terms and definitions .xii
4 Safety requirements and/or protective/risk reduction measures. xvii
4.1 General . xvii
4.1.1 Emergency stop . xviii
4.1.2 Guards . xviii
4.1.3 Electro-sensitive protective equipment (ESPE) in the form of light curtains . xx
4.1.4 Two-hand control devices .xxi
4.1.5 Pressure sensitive mats, floors and edges.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.