EN 12012-2:2001+A2:2008
(Main)Plastics and rubber machines - Size reduction machines - Part 2: Safety requirements for strand pelletisers
Plastics and rubber machines - Size reduction machines - Part 2: Safety requirements for strand pelletisers
This standard specifies the essential safety requirements applicable to the design and construction of strand pelletisers used for plastics and rubber and fed continuously by an extruder or a reactor.
The machine begins with the feed opening of the feeding device, or start-up devices if fitted, and ends with the discharge area.
Only the significant hazards listed in clause 4 and dealt with in clause 5 are subject to this standard.
NOTE Directive 94/9/EC concerning equipment and protective systems intended for use in potentially explosive atmospheres can be applicable to the type of machine or equipment covered by this European Standard. The present standard is not intended to provide means of complying with the essential health and safety requirements of Directive 94/9/EC.
This standard applies to machines which are manufactured after the date of approval of this standard by CEN.
Kunststoff- und Gummimaschinen - Zerkleinerungsmaschinen - Teil 2: Sicherheitsanforderungen an Stranggranulatoren
!Diese Norm behandelt die wesentlichen Sicherheitsanforderungen, die bei Konzipierung und Bau von kontinuierlich von einem Extruder oder einem Reaktor beschickten Stranggranulatoren für Kunststoffe und Gummi anzuwenden sind.
Die Maschine beginnt mit der Beschickungseinrichtung oder, falls damit ausgerüstet, mit der Anfahr-einrichtung und endet mit dem Entnahmebereich.
Nur die in Abschnitt 4 angegebenen und in Abschnitt 5 behandelten signifikanten Gefährdungen sind Gegen-stand dieser Norm.
ANMERKUNG Die Richtlinie 94/9/EG bezüglich Geräte und Schutzsysteme zur bestimmungsgemäßen Verwendung in explosionsgefährdeten Bereichen kann bei Maschinen oder Bauteilen nach dieser Europäischen Norm zur Anwendung kommen. Es kann nicht davon ausgegangen werden, dass die vorliegende Norm mit der Richtlinie 94/9/EG in Überein¬stimmung ist.
Diese Norm gilt für Maschinen, die nach dem Annahmedatum der Norm durch CEN hergestellt worden sind."
Machines pour les matières plastiques et le caoutchouc - Machines à fragmenter - Partie 2: Prescriptions de sécurité relatives aux granulateurs à joncs
!La présente norme spécifie les exigences essentielles de sécurité relatives à la conception et à la construction
des granulateurs à joncs utilisés pour les matières plastiques et le caoutchouc et alimentés en continu par une
extrudeuse et un réacteur.
La machine commence à l'ouverture du dispositif d'alimentation ou au dispositif de démarrage s'il existe et se termine
à la zone de déchargement.
Seuls les phénomènes dangereux significatifs énumérés à l'article 4 et traités à l'article 5 sont couverts par la
présente norme.
NOTE La Directive 94/9/CE relative aux appareils et systèmes de protection destinés à être utilisés en atmosphères
explosibles peut être appliquée au type de machine ou équipement couvert par la présente Norme européenne. La présente
norme n’est pas destinée à fournir un moyen de satisfaire aux exigences essentielles de santé et de sécurité de la Directive
94/9/CE.
Ce document n’est pas applicable aux granulateurs à joncs qui ont été fabriqués avant la date de publication de ce
document par le CEN."
Stroji za predelavo gume in plastike - Drobilni stroji - 2. del: Varnostne zahteve za iztiskovalne granulatorje
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Stroji za predelavo gume in plastike - Drobilni stroji - 2. del: Varnostne zahteve za iztiskovalne granulatorjeKunststoff- und Gummimaschinen - Zerkleinerungsmaschinen - Teil 2: Sicherheitsanforderungen an StranggranulatorenMachines pour les matières plastiques et le caoutchouc - Machines à fragmenter - Partie 2: Prescriptions de sécurité relatives aux granulateurs à joncsPlastics and rubber machines - Size reduction machines - Part 2: Safety requirements for strand pelletisers83.200Oprema za gumarsko industrijo in industrijo polimernih materialovEquipment for the rubber and plastics industriesICS:Ta slovenski standard je istoveten z:EN 12012-2:2001+A2:2008SIST EN 12012-2:2002+A2:2008en01-november-2008SIST EN 12012-2:2002+A2:2008SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 12012-2:2001+A2
September 2008 ICS 83.200 Supersedes EN 12012-2:2001 English Version
Plastics and rubber machines - Size reduction machines - Part 2: Safety requirements for strand pelletisers
Machines pour les matières plastiques et le caoutchouc - Machines à fragmenter - Partie 2: Prescriptions de sécurité relatives aux granulateurs à joncs
Kunststoff- und Gummimaschinen - Zerkleinerungsmaschinen - Teil 2: Sicherheitsanforderungen an Stranggranulatoren This European Standard was approved by CEN on 10 May 2001 and includes Amendment 1 approved by CEN on 14 November 2003 and Amendment 2 approved by CEN on 8 June 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36
B-1050 Brussels © 2008 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12012-2:2001+A2:2008: ESIST EN 12012-2:2002+A2:2008
Measurement and declaration of noise emission values.17 Annex ZA (informative)
####Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EC$$$$.21 Annex ZB (informative)
####Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC$$$$.22
• addition of Annex ZB.
• editorial changes of EN 292-1:1991 to EN ISO 12100-1:2003 and of EN 292-2:1991 to EN ISO 12100-2:2003 in the following clauses and sub-clauses:
2, 5, Table 1, 7.1.1, Annex A, A.3.1. • minor changes of Foreword, sub-clause: 7.2, second and third indents, Annex A, A.7, third indent.
This document supersedes EN 12012-2:2001. The start and finish of text introduced or altered by amendment is indicated in the text by tags
!" and # $. This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). #For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this document.$ This is the second in a series of standards on the safety of size reduction machines. Part 1 deals with blade granulators; Part 3 deals with shredders. Annex A is normative. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
The machine begins with the feed opening of the feeding device, or start-up devices if fitted, and ends with the discharge area.
Only the significant hazards listed in clause 4 and dealt with in clause 5 are subject to this standard.
NOTE Directive 94/9/EC concerning equipment and protective systems intended for use in potentially explosive atmospheres can be applicable to the type of machine or equipment covered by this European Standard. The present standard is not intended to provide means of complying with the essential health and safety requirements of Directive 94/9/EC.
This standard applies to machines which are manufactured after the date of approval of this standard by CEN." 2 Normative references This European standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references subsequent amendments to or revisions of any of these publications apply to this European standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). #deleted text$ EN 294:1992, Safety of Machinery - Safety distances to prevent danger zones being reached by the upper limbs EN 418:1992, Safety of Machinery - Emergency stop equipment, functional aspects - Principles for design EN 563:1994, Safety of Machinery - Temperatures of touchable surfaces - Ergonomics data to establish temperature limit values for hot surfaces EN 953:1997, Safety of Machinery – Guards - General requirements for the design and construction of fixed and movable guards EN 954-1:1996, Safety of Machinery - Safety related parts of control systems - Part 1: General principles for design SIST EN 12012-2:2002+A2:2008
EN 12012-2:2001+A2
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.