EN ISO 3104:2020
(Main)Petroleum products - Transparent and opaque liquids - Determination of kinematic viscosity and calculation of dynamic viscosity (ISO 3104:2020)
Petroleum products - Transparent and opaque liquids - Determination of kinematic viscosity and calculation of dynamic viscosity (ISO 3104:2020)
This document specifies Procedure A, using manual glass viscometers, and Procedure B, using glass capillary viscometers in an automated assembly, for the determination of the kinematic viscosity, ν, of liquid petroleum products, both transparent and opaque, by measuring the time for a volume of liquid to flow under gravity through a calibrated glass capillary viscometer. The dynamic viscosity, η, is obtained by multiplying the measured kinematic viscosity by the density, ρ, of the liquid. The range of kinematic viscosities covered in this test method is from 0,2 mm2/s to 300 000 mm2/s over the temperature range ?20 °C to +150 °C.
NOTE The result obtained from this document is dependent upon the behaviour of the sample and is intended for application to liquids for which primarily the shear stress and shear rates are proportional (Newtonian flow behaviour). If, however, the viscosity varies significantly with the rate of shear, different results can be obtained from viscometers of different capillary diameters. The procedure and precision values for residual fuel oils, which under some conditions exhibit non-Newtonian behaviour, have been included.
Mineralölerzeugnisse - Durchsichtige und undurchsichtige Flüssigkeiten - Bestimmung der kinematischen Viskosität und Berechnung der dynamischen Viskosität (ISO 3104:2020)
Dieses Dokument legt Verfahren A mit manuellen Glas-Viskosimetern und Verfahren B mit Glas-Kapillarviskosimetern in einer automatisierten Apparatur zur Bestimmung der kinematischen Viskosität ν von flüssigen, sowohl durchsichtigen als auch undurchsichtigen, Mineralölerzeugnissen fest. Dabei wird die Durchflusszeit eines Flüssigkeitsvolumens unter dem Einfluss der Schwerkraft durch ein kalibriertes Glas-Kapillarviskosimeter gemessen. Die dynamische Viskosität η wird erhalten, indem die gemessene kinematische Viskosität mit der Dichte ρ der Flüssigkeit multipliziert wird. Die mit diesem Prüfverfahren abgedeckten kinematischen Viskositäten liegen im Bereich von 0,2 mm2/s bis 300 000 mm2/s über den Temperaturbereich −20 °C bis +150 °C.
ANMERKUNG Das mit diesem Dokument erhaltene Ergebnis hängt vom Verhalten der Probe ab; die Norm ist für Flüssigkeiten vorgesehen, für die in erster Linie Schubspannung und Schergeschwindigkeit proportional sind (Newtonsches Fließverhalten). Wenn sich jedoch die Viskosität signifikant mit der Schergeschwindigkeit ändert, können unterschiedliche Ergebnisse mit Viskosimetern unterschiedlichen Kapillardurchmessers erhalten werden. Das Verfahren und Präzisionswerte für Rückstandsheizöle, die unter gewissen Bedingungen nicht-newtonsches Verhalten zeigen, wurden ebenfalls aufgenommen.
WARNUNG - Dieses Dokument beansprucht nicht, alle damit verbundenen Sicherheitsprobleme, soweit vorhanden, zu behandeln. Es liegt in der Verantwortung des Anwenders dieses Dokuments, vor der Anwendung dieses Dokuments geeignete Maßnahmen für die Sicherheit und den Gesundheitsschutz des Personals zu ergreifen, und die Geltung weiterer Auflagen zu prüfen.
Produits pétroliers - Liquides opaques et transparents - Détermination de la viscosité cinématique et calcul de la viscosité dynamique (ISO 3104:2020)
Le présent document spécifie un Mode opératoire A utilisant des viscosimètres manuels en verre et un Mode opératoire B utilisant des viscosimètres à capillaires en verre dans un assemblage automatisé, pour la détermination de la viscosité cinématique, ν, de produits pétroliers liquides transparents et opaques, pour un volume de liquide s'écoulant sous la gravité à travers un viscosimètre à capillaires en verre étalonné. La viscosité dynamique, η, est obtenue en multipliant la viscosité cinématique mesurée par la masse volumique, ρ, du liquide. La plage de viscosités cinématiques couverte dans la présente méthode d'essai est comprise entre 0,2 mm2/s et 300 000 mm2/s sur la plage de températures de ?20 °C à +150 °C.
NOTE Le résultat obtenu avec le présent document dépend du comportement de l'échantillon et est destiné à une application sur des liquides dont les contraintes de cisaillement et les vitesses de cisaillement sont essentiellement proportionnelles (comportement d'écoulement newtonien). Si, cependant, la viscosité varie considérablement avec la vitesse de cisaillement, des résultats différents peuvent être obtenus à partir de viscosimètres ayant des diamètres de capillaire différents. Ont été inclus le mode opératoire et les valeurs de fidélité pour des combustibles résiduels qui, dans certaines conditions, présentent un comportement non newtonien.
Naftni proizvodi - Prozorne in neprozorne tekočine - Določevanje kinematične viskoznosti in izračun dinamične viskoznosti (ISO 3104:2020)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2020
Nadomešča:
SIST EN ISO 3104:1998
SIST EN ISO 3104:1998/AC:1999
Naftni proizvodi - Prozorne in neprozorne tekočine - Določevanje kinematične
viskoznosti in izračun dinamične viskoznosti (ISO 3104:2020)
Petroleum products - Transparent and opaque liquids - Determination of kinematic
viscosity and calculation of dynamic viscosity (ISO 3104:2020)
Mineralölerzeugnisse - Durchsichtige und undurchsichtige Flüssigkeiten - Bestimmung
der kinematischen Viskosität und Berechnung der dynamischen Viskosität (ISO
3104:2020)
Produits pétroliers - Liquides opaques et transparents - Détermination de la viscosité
cinématique et calcul de la viscosité dynamique (ISO 3104:2020)
Ta slovenski standard je istoveten z: EN ISO 3104:2020
ICS:
75.080 Naftni proizvodi na splošno Petroleum products in
general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 3104
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2020
EUROPÄISCHE NORM
ICS 75.080 Supersedes EN ISO 3104:1996
English Version
Petroleum products - Transparent and opaque liquids -
Determination of kinematic viscosity and calculation of
dynamic viscosity (ISO 3104:2020)
Produits pétroliers - Liquides opaques et transparents Mineralölerzeugnisse - Durchsichtige und
- Détermination de la viscosité cinématique et calcul de undurchsichtige Flüssigkeiten - Bestimmung der
la viscosité dynamique (ISO 3104:2020) kinematischen Viskosität und Berechnung der
dynamischen Viskosität (ISO 3104:2020)
This European Standard was approved by CEN on 16 July 2020.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 3104:2020 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 3104:2020) has been prepared by Technical Committee ISO/TC 28 "Petroleum
and related products, fuels and lubricants from natural or synthetic sources" in collaboration with
Technical Committee CEN/TC 19 “Gaseous and liquid fuels, lubricants and related products of
petroleum, synthetic and biological origin.” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2021, and conflicting national standards shall
be withdrawn at the latest by March 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 3104:1996.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 3104:2020 has been approved by CEN as EN ISO 3104:2020 without any modification.
INTERNATIONAL ISO
STANDARD 3104
Third edition
2020-09
Petroleum products — Transparent
and opaque liquids — Determination
of kinematic viscosity and calculation
of dynamic viscosity
Produits pétroliers — Liquides opaques et transparents —
Détermination de la viscosité cinématique et calcul de la viscosité
dynamique
Reference number
ISO 3104:2020(E)
©
ISO 2020
ISO 3104:2020(E)
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
ISO 3104:2020(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
5 Reagents and materials . 2
6 Apparatus design and requirements . 3
7 Verification . 6
7.1 Viscometer . 6
7.2 Liquid-in-glass thermometer. 6
7.3 Digital contact thermometer . 7
7.4 Timer . 7
8 Re-calibration . 7
9 Quality control . 7
10 Sample preparation . 7
10.1 Pre-analysis sample conditioning . 7
10.2 Visual inspection and filtering . 8
11 Procedure A — Manual equipment . 8
12 Procedure B — Automated equipment .10
13 Cleaning of the viscometer tube .11
14 Calculation .11
14.1 Procedure A — Manual viscometers .11
14.2 Procedure B — Automated viscometers .12
15 Expression of results .13
16 Precision of procedure A .13
16.1 Determinability, d .13
16.2 Repeatability, r .14
16.3 Reproducibility, R .14
17 Precision of Procedure B .15
17.1 Determinability, d .15
17.2 Repeatability, r .15
17.3 Reproducibility, R .15
18 Test report .15
Annex A (normative) Viscometer types, calibration and verification .17
Annex B (normative) Thermometers for kinematic viscosity test .18
Annex C (normative) Conditioning of samples prior to manual or automated analysis .22
Annex D (normative) Calculation of acceptable tolerance zone (band) to determine
conformance with a certified reference material .23
Bibliography .24
ISO 3104:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that commit
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.