Rubber hoses and hose assemblies - Rubber-covered spiral wire reinforced hydraulic type - Specification

This European Standard specifies requirements for four types of rubber-covered spiral wire reinforced hydraulic hoses and hose assemblies of nominal bore from 6 to 51: Types 4SP, 4SH, R12 and R13. They are all suitable for use with:
-   hydraulic fluids in accordance with ISO 6743 4 with the exception of HFD R, HFD S and HFD T at temperatures ranging from −40 °C to +100 °C for types 4SP and 4SH and −40 °C to +120 °C for types R12 and R13;
-   water based fluids at temperatures ranging from −40 °C to 70 °C;
-   water fluids at temperatures ranging from 0 °C to 70 °C.
This European Standard does not include requirements for end fittings. It is limited to the performance of hoses and hose assemblies.
NOTE 1   The hoses are not suitable for use with castor oil based nor ester based fluids.
NOTE 2   Hoses and hose assemblies are not be operated outside the limits of this standard.
NOTE 3   Requirements for hydraulic hoses for underground mining are standardised in a separate standard.

Gummischläuche und -schlauchleitungen - Hydraulikschläuche mit Drahtspiraleinlage - Spezifikation

Diese Europäische Norm legt Anforderungen für vier Typen von Schläuchen und Schlauchleitungen mit Drahtspiraleinlagen vom Nenndurchmesser 6 bis 51 fest. Sie sind geeignet zur Verwendung mit:
   Hydraulikflüssigkeiten nach ISO 6743-4 mit Ausnahme von HFD R, HFD S und HFD T in einem Temperaturbereich von – 40 °C bis + 100 °C bei den Typen 4SP und 4SH und – 40 °C bis + 120 °C bei den Typen R12 und R13;
   wässrigen Flüssigkeiten in einem Temperaturbereich von – 40 °C bis + 70 °C;
   Wasser in einem Temperaturbereich von 0 °C bis + 70 °C.
Die Norm enthält keine Anforderungen an die Armaturen. Sie beschränkt sich auf die Leistungsfähigkeit der Schläuche und Schlauchleitungen.
ANMERKUNG 1   Die Schläuche sind für Flüssigkeiten auf Rizinusöl- oder Esterbasis nicht geeignet.
ANMERKUNG 2   Die Schläuche und Schlauchleitungen sollten nicht außerhalb der Grenzen dieser Norm verwendet werden.
ANMERKUNG 3   Anforderungen an Hydraulikschläuche für den untertägigen Bergbau sind in separaten Normen genormt.

Tuyaux et flexibles en caoutchouc - Type hydraulique avec armature hélicoïdale de fils métalliques - Spécification

La présente Norme européenne spécifie les exigences pour quatre types de tuyaux et flexibles revêtus de caoutchouc, renforcés par des fils métalliques en spirale, d’alésage nominal de 6 à 51 : Types 4SP, 4SH, R12 et R13. Ils sont destinés à être utilisés avec :
-   les fluides hydrauliques conformes à l’EN ISO 6743-4 à l’exception des HFD R, HFD S et HFD T, dans une plage de températures de -40 ˚C à +100 ˚C pour les types 4SP et 4SH, et de -40 ˚C à +120 ˚C pour les types R12 et R13 ;
-   les fluides aqueux dans une plage de températures de -40 ˚C à 70 ˚C ;
-   l’eau dans une plage de températures de 0 ˚C à 70 ˚C.
La présente Norme européenne ne contient pas d'exigences relatives aux extrémités de raccordement. Elle se limite aux performances des tuyaux et flexibles.
NOTE 1   Les tuyaux ne conviennent pas pour des utilisations avec des fluides à base d'huile de ricin ou d'ester.
NOTE 2   Il ne convient pas d’utiliser les tuyaux et flexibles en dehors des limites de la présente norme.
NOTE 3   Les exigences pour les tuyaux hydrauliques pour mines souterraines font l'objet de normes séparées.

Gumene cevi in cevni priključki - S spiralnim gumiranim jeklenim kordom ojačene hidravlične cevi - Specifikacija

General Information

Status
Withdrawn
Publication Date
31-Mar-2015
Withdrawal Date
05-Mar-2019
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
06-Mar-2019

Relations

Buy Standard

Standard
EN 856:2015
English language
17 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
k FprEN 856:2015
English language
18 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 856:2015
01-junij-2015
1DGRPHãþD
SIST EN 856:2000
*XPHQHFHYLLQFHYQLSULNOMXþNL6VSLUDOQLPJXPLUDQLPMHNOHQLPNRUGRPRMDþHQH
KLGUDYOLþQHFHYL6SHFLILNDFLMD
Rubber hoses and hose assemblies - Rubber-covered spiral wire reinforced hydraulic
type - Specification
Gummischläuche und -schlauchleitungen - Hydraulikschläuche mit Drahtspiraleinlage -
Spezifikation
Tuyaux et flexibles en caoutchouc - Type hydraulique avec armature hélicoidale de fils
métalliques - Spécification
Ta slovenski standard je istoveten z: EN 856:2015
ICS:
23.040.70 Gumene cevi in armature Hoses and hose assemblies
SIST EN 856:2015 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 856:2015

---------------------- Page: 2 ----------------------

SIST EN 856:2015

EUROPEAN STANDARD
EN 856

NORME EUROPÉENNE

EUROPÄISCHE NORM
April 2015
ICS 23.100.40 Supersedes EN 856:1996
English Version
Rubber hoses and hose assemblies - Rubber-covered spiral wire
reinforced hydraulic type - Specification
Tuyaux et flexibles en caoutchouc - Type hydraulique avec Gummischläuche und -schlauchleitungen -
armature hélicoïdale de fils métalliques - Spécification Hydraulikschläuche mit Drahtspiraleinlage - Spezifikation
This European Standard was approved by CEN on 31 January 2015.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 856:2015 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 856:2015
EN 856:2015 (E)
Contents Page
Foreword .3
1 Scope .4
2 Normative references .4
3 Types of hose .5
4 Materials and construction .5
4.1 Hoses .5
4.2 Hose assemblies .5
5 Dimensions .5
5.1 Diameters and concentricity .5
5.2 Length .7
5.2.1 Hoses .7
5.2.2 Hose assemblies .7
6 Requirements .
...

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Gummischläuche und -schlauchleitungen - Hydraulikschläuche mit Drahtspiraleinlage - SpezifikationTuyaux et flexibles en caoutchouc - Type hydraulique avec armature hélicoidale de fils métalliques - SpécificationRubber hoses and hose assemblies - Rubber-covered spiral wire reinforced hydraulic type - Specification23.040.70Gumene cevi in armatureHoses and hose assembliesICS:Ta slovenski standard je istoveten z:FprEN 856kSIST FprEN 856:2015en,fr,de01-januar-2015kSIST FprEN 856:2015SLOVENSKI
STANDARD



kSIST FprEN 856:2015



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
FINAL DRAFT
FprEN 856
October 2014 ICS 23.100.40 Will supersede EN 856:1996English Version
Rubber hoses and hose assemblies - Rubber-covered spiral wire reinforced hydraulic type - Specification
Tuyaux et flexibles en caoutchouc - Type hydraulique avec armature hélicoidale de fils métalliques - Spécification
Gummischläuche und -schlauchleitungen - Hydraulikschläuche mit Drahtspiraleinlage - Spezifikation This draft European Standard is submitted to CEN members for formal vote. It has been drawn up by the Technical Committee CEN/TC 218.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. FprEN 856:2014 EkSIST FprEN 856:2015



FprEN 856:2014 (E) 2 Contents Page
Foreword .3 1 Scope .4 2 Normative references .4 3 Types of hose .5 4 Materials and construction .5 4.1 Hoses .5 4.2 Hose assemblies .5 5 Dimensions .5 5.1 Diameters and concentricity .5 5.2 Length .8 5.2.1 Hoses .8 5.2.2 Hose assemblies .8 6 Requirements .9 6.1 Hydrostatic requirements .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.