EN 16436-1:2014

Rubber and plastics hoses, tubing and assemblies for use with propane and butane and their mixture in the vapour phase - Part 1: Hoses and tubings

This European Standard specifies the characteristics and performance requirements for tubing and hoses made of either rubber or plastics for use with commercial propane and commercial butane and mixtures thereof, in the vapour phase, for connection of appliances, from:
-   pressurized gas container to a regulating device,
-   pressurized gas container to an appliance,
-   regulating device to an appliance, and
-   regulating device to installation pipework,
in environments of a temperature range from –30 °C to +70 °C. Working pressures are from 0 bar to 30 bar.
Three classes are defined in Table 1 according to the maximum working pressures and minimum ambient temperatures.
This European Standard only covers the tubing or hose part of assemblies. The assemblies themselves will be covered by EN 16436-2.
This European Standard does not apply to hoses for:
-   welding purposes (see EN ISO 3821, EN 1327);
-   propulsion purposes;
-   LPG transfer purposes (see EN 1762).

Gummi- und Kunststoff-Schläuche und -Schlauchleitungen mit und ohne Einlage zur Verwendung mit Propan, Butan und deren Gemische in der Gasphase - Teil 1: Schäuche mit und ohne Einlage

Diese Europäische Norm legt die Merkmale und Leistungsanforderungen für Gummi- oder Kunststoff-schläuche mit und ohne Einlage fest, für den Einsatz mit handelsüblichem Propan und handelsüblichem Butan und deren Gemischen in der Gasphase für die Verbindung von Geräten, von
- einem mit Druck beaufschlagten Gasbehälter an ein Druckregelgerät,
- einem mit Druck beaufschlagten Gasbehälter an ein Gasgerät,
- einem Druckregelgerät an ein Gasgerät und
- einem Druckregelgerät an eine Metallleitung,
in einem Umgebungstemperaturbereich von −30 °C bis +70 °C. Die Betriebsdrücke liegen zwischen 0 bar und 30 bar.
In Tabelle 1 werden drei Klassen in Abhängigkeit vom höchsten Betriebsdruck und der niedrigsten Umgebungstemperatur festgelegt.
Diese Europäische Norm behandelt nur den Schlauchteil, mit oder ohne Einlage, von Schlauchleitungen. Die Schlauchleitungen werden in EN 16436-2 geregelt.
Diese Europäische Norm gilt nicht für Schläuche für:
- Schweißanwendungen (siehe EN ISO 3821, EN 1327);
- Antriebszwecke;
- Flüssiggasfüll-und umfüllverfahren (siehe EN 1762).

Tuyaux, tubes et flexibles en caoutchouc et en plastique pour utilisation avec le propane, le butane et leurs mélanges en phase vapeur - Partie 1: Tuyaux et tubes

La présente Norme européenne spécifie les caractéristiques et les exigences de performance des tubes et
tuyaux en caoutchouc ou en plastique, pour utilisation avec le propane commercial, le butane commercial et
leurs mélanges, en phase vapeur, pour le raccordement des appareils, depuis :
- des récipients de gaz sous pression à un dispositif de détente,
- des récipients de gaz sous pression à un appareil,
- un dispositif de détente à un appareil, et
- un dispositif de détente à la tuyauterie d’une installation,
dans des conditions de température située dans une plage de valeurs comprises entre - 30 °C et + 70 °C. Les
pressions de service sont comprises entre 0 bar et 30 bar.
Trois classes sont définies dans le Tableau 1 en fonction de la pression maximale de service et de la
température ambiante minimale.
La présente Norme européenne ne s’applique qu’à la partie tube ou tuyaux des flexibles qui seront couverts
par une autre norme.
La présente Norme européenne ne s’applique pas aux tuyaux utilisés pour :
- les besoins de soudure (voir l’EN ISO 3821, EN 1327) ;
- les besoins de propulsion ;
- les besoins de transfert de gaz de pétrole liquéfié (voir l’EN 1762).

Gumeni in plastični priključki, cevovodi in cevi za propan, butan in njune zmesi v plinastem stanju - 1. del: Cevi in cevovodi

EN 16436-1 določa značilnosti in zahteve glede učinkovitosti za gumene in plastične priključke in cevi za tržni propan, tržni butan in njune zmesi v plinastem stanju, za priključitev aparatov, kot so: - tlačna posoda za plin z napravo za uravnavanje, - tlačna posoda za plin z aparatom, - naprava za uravnavanje z aparatom in - naprava za uravnavanje z napeljavo, v okoljih s temperaturo od −30 °C do +70 °C. Delovni tlak znaša od 0 do 30 barov. V tabeli 1 so določeni trije razredi glede na najvišji delovni tlak in najmanjše temperature okolja. Ta evropski sistem zajema samo priključke in cevi, ki so del priključkov. Priključke bo obravnaval standard EN 16436-2. Ta evropski standard se ne uporablja za cevi za: - varjenje (glejte EN ISO 3821, EN 1327); - pogon; - pretok utekočinjenega naftnega plina (UNP) (glejte EN 1762).

General Information

• Status: Withdrawn
• Publication Date: 06-May-2014
• Withdrawal Date: 01-Dec-2015
• ICS: 23.040.70 - Hoses and hose assemblies
• Technical Committee: CEN/TC 181 - Dedicated liquified petroleum gas appliances
• Drafting Committee: CEN/TC 181/WG 3 - Small non-domestic space heaters
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 02-Dec-2015
• Directive: 2009/142/EC - DIRECTIVE 2009/142/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 30 November 2009 relating to appliances burning gaseous fuels
• Directive: 90/396/EEC - Appliances burning gaseous fuels
• Mandate: M/BC/CEN/89/6 - Standardization request to CEN concerning appliances burning gaseous fuels
• Ref Project: SIST EN 16436-1:2014 - Rubber and plastics hoses, tubing and assemblies for use with propane and butane and their mixture in the vapour phase - Part 1: Hoses and tubings

Relations

• Merged Into: EN 16436-1:2014+A1:2015 - Rubber and plastics hoses, tubing and assemblies for use with propane and butane and their mixture in the vapour phase - Part 1: Hoses and tubings
• Effective Date: 18-Jan-2023
• Amended By: EN 16436-1:2014/FprA1:2015 - Rubber and plastics hoses, tubing and assemblies for use with propane and butane and their mixture in the vapour phase - Part 1: Hoses and tubings
• Effective Date: 28-Jan-2015

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Gummi- und Kunststoff-Schläuche und -Schlauchleitungen mit und ohne Einlage zur Verwendung mit Propan, Butan und deren Gemische in der Gasphase - Teil 1: Schäuche mit und ohne EinlageTuyaux, tubes et flexibles en caoutchouc et en plastique pour utilisation avec le propane, le butane et leurs mélanges en phase vapeur - Partie 1: Tuyaux et tubesRubber and plastics hoses, tubing and assemblies for use with propane and butane and their mixture in the vapour phase - Part 1: Hoses and tubings83.140.40Gumene ceviHosesICS:Ta slovenski standard je istoveten z:EN 16436-1:2014SIST EN 16436-1:2014en,fr,de01-julij-2014SIST EN 16436-1:2014SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 16436-1
May 2014 ICS 23.040.70 English Version
Rubber and plastics hoses, tubing and assemblies for use with propane and butane and their mixture in the vapour phase - Part 1: Hoses and tubings
Tuyaux, tubes et flexibles en caoutchouc et en plastique pour utilisation avec le propane, le butane et leurs mélanges en phase vapeur - Partie 1: Tuyaux et tubes
Gummi- und Kunststoffschläuche mit und ohne Einlage zur Verwendung mit Propan, Butan und deren Gemische in der Gasphase This European Standard was approved by CEN on 6 March 2014.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16436-1:2014 ESIST EN 16436-1:2014

Test methods for tubing and hoses . 12 Bibliography . 17
 regulating device to installation pipework,
in environments of a temperature range from –30 °C to +70 °C. Working pressures are from 0 bar to 30 bar. Three classes are defined in Table 1 according to the maximum working pressures and minimum ambient temperatures. This European Standard only covers the tubing or hose part of assemblies. The assemblies themselves will be covered by EN 16436-2. This European Standard does not apply to hoses for:  welding purposes (see EN ISO 3821, EN 1327);  propulsion purposes;  LPG transfer purposes (see EN 1762). 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN ISO 176, Plastics - Determination of loss of plasticizers - Activated carbon method (ISO 176) EN ISO 1402, Rubber and plastics hoses and hose assemblies - Hydrostatic testing (ISO 1402) EN ISO 4080, Rubber and plastics hoses and hose assemblies - Determination of permeability to gas (ISO 4080) EN ISO 4671, Rubber and plastics hoses and hose assemblies - Methods of measurement of the dimensions of hoses and the lengths of hose assemblies (ISO 4671) EN ISO 7326, Rubber and plastics hoses - Assessment of ozone resistance under static conditions (ISO 7326) EN ISO 8033, Rubber and plastics hoses - Determination of adhesion between components (ISO 8033) EN ISO 8330:2008, Rubber and plastics hoses and hose assemblies - Vocabulary (ISO 8330:2007) EN ISO 10619-2, Rubber and plastics hoses and tubing - Measurement of flexibility and stiffness - Part 2: Bending tests at sub-ambient temperatures (ISO 10619-2) SIST EN 16436-1:2014

a) option 1
b) option 2 Key
orange colour
black colour Figure 1 – Possible marking for classes 1, 2 or 3 SIST EN 16436-1:2014

Key
orange colour
white colour Figure 2 – Possible marking for classes 1 or 2 6 Dimensions of tubing and hoses 6.1 Inside diameters, wall thicknesses and concentricity When measured in accordance with EN ISO 4671 the inside diameters, tolerances and concentricity shall conform to the values given in Table 2. Table 2 — Dimensions of hoses or tubing Dimensions in millimetres Inside diameters 3,2 4,0 5,0 6,3 8,0 9,0 10,0 10,5 12,5 Tolerance of inside diameter ± 0,3 ± 0,4 ± 0,4 ± 0,5 ± 0,5 ± 0,5 ± 0,6 ± 0,6 ± 0,6 Maximum variation in concentricity 0,3 0,4 0,4 0,4 0,5 0,5 0,5 0,5 0,5 Wall thickness class 1 and class 2 2,5 3,5 3,5 3,5 3,5 3,5 5,0 5,0 5,0 Wall thickness class 3 3,5 4,0 4,0 5,0 5,0 5,0 5,0 5,0 6,0 Tolerance of wall thickness ± 0,4 ± 0,4 ± 0,4 ± 0,4 ± 0,5 ± 0,5 ± 0,5 ± 0,5 ± 0,5 6.2 Measurement of ovality When measuring on a hose cross section, the minimum diameter Dmin and the maximum diameter Dmax, the ratio Dmin/Dmax shall not be less than 0,80. 7 Properties of materials for tubing, lining and cover of hoses 7.1 Tensile strength and elongation at break When tested in accordance with A.2, the materials used for tubing, lining and cover of hoses shall conform to the values given in Table 3. SIST EN 16436-1:2014
...