EN ISO 6134:2024
(Main)Rubber hoses and hose assemblies for saturated steam - Specification (ISO 6134:2024)
Rubber hoses and hose assemblies for saturated steam - Specification (ISO 6134:2024)
This document specifies requirements for hoses and hose assemblies made of rubber and hose fittings made of metal, which are designed to convey saturated steam and hot water condensate.
This document applies to the following two types of hoses and hose assemblies:
— low pressure, with a maximum working pressure of 0,6 MPa (6 bar);
— high pressure, with a maximum working pressure of 1,8 MPa (18 bar).
Each type is divided into two classes, having either an oil resistant or non-oil resistant cover.
Gummischläuche und -schlauchleitungen für gesättigten Dampf - Spezifikation (ISO 6134:2024)
Dieses Dokument legt die Anforderungen an Schläuche und Schlauchleitungen fest, die aus Gummi hergestellt und mit Schlaucharmaturen aus Metall ausgestattet sind und die für die Förderung von gesättigtem Dampf und Heißwasserkondensat bestimmt sind.
Dieses Dokument ist anwendbar für die folgenden zwei Typen von Schläuchen und Schlauchleitungen:
- niedriger Druck, mit einem maximalen Betriebsdruck von 0,6 MPa (6 bar);
- hoher Druck, mit einem maximalen Betriebsdruck von 1,8 MPa (18 bar).
Jeder Typ ist in zwei Klassen unterteilt, die entweder eine ölbeständige oder eine nicht ölbeständige Außenschicht besitzen.
Tuyaux et flexibles en caoutchouc pour vapeur saturée - Spécification (ISO 6134:2024)
Le présent document spécifie des exigences relatives aux tuyaux et de flexibles en caoutchouc et embouts en métal, qui sont conçus pour véhiculer de la vapeur saturée et du condensat d'eau chaude.
Le présent document s'applique aux deux types de tuyaux et de flexibles suivants:
— à basse pression, avec une pression maximale de service de 0,6 MPa (6 bar);
— à haute pression, avec une pression maximale de service de 1,8 MPa (18 bar).
Chaque type est divisé en deux classes, ayant soit un revêtement résistant à l'huile soit un revêtement non résistant à l'huile.
Gumene cevi in cevni priključki za nasičeno paro - Specifikacija (ISO 6134:2024)
Standard ISO 6134:2017 določa zahteve za dve vrsti cevi in cevnih priključkov (nizkotlačni z največjim delovnim tlakom 6 barov in visokotlačni z največjim delovnim tlakom 18 barov), izdelanih iz gume, in za cevne fitinge, izdelane iz kovine, ki so namenjeni za odvajanje nasičene pare in kondenzirane vroče vode.
Vsaka vrsta je razdeljena v dva razreda, ki vključujeta pokrov, ki je ali ni odporen proti olju.
OPOMBA: Informacije o pogostosti preskušanja cevnih priključkov so podane v dodatkih A in B.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2024
Gumene cevi in cevni priključki za nasičeno paro - Specifikacija (ISO 6134:2024)
Rubber hoses and hose assemblies for saturated steam - Specification (ISO 6134:2024)
Gummischläuche und -schlauchleitungen für gesättigten Dampf - Spezifikation (ISO
6134:2024)
Tuyaux et flexibles en caoutchouc pour vapeur saturée - Spécification (ISO 6134:2024)
Ta slovenski standard je istoveten z: EN ISO 6134:2024
ICS:
23.040.70 Gumene cevi in armature Hoses and hose assemblies
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 6134
EUROPEAN STANDARD
NORME EUROPÉENNE
June 2024
EUROPÄISCHE NORM
ICS 23.040.70 Supersedes EN ISO 6134:2017
English Version
Rubber hoses and hose assemblies for saturated steam -
Specification (ISO 6134:2024)
Tuyaux et flexibles en caoutchouc pour vapeur saturée Gummischläuche und -schlauchleitungen für
- Spécification (ISO 6134:2024) gesättigten Dampf - Spezifikation (ISO 6134:2024)
This European Standard was approved by CEN on 7 June 2024.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 6134:2024 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 6134:2024) has been prepared by Technical Committee ISO/TC 45 "Rubber and
rubber products" in collaboration with Technical Committee CEN/TC 218 “Rubber and plastics hoses
and hose assemblies” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by December 2024, and conflicting national standards
shall be withdrawn at the latest by December 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 6134:2017.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 6134:2024 has been approved by CEN as EN ISO 6134:2024 without any modification.
International
Standard
ISO 6134
Fifth edition
Rubber hoses and hose assemblies
2024-05
for saturated steam — Specification
Tuyaux et flexibles en caoutchouc pour vapeur saturée —
Spécification
Reference number
ISO 6134:2024(en) © ISO 2024
ISO 6134:2024(en)
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 6134:2024(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 General requirements . 2
5 Classification . 2
6 Materials and construction . 2
7 Dimensions and tolerances . 3
7.1 Diameters, thickness of lining and cover and bend radii .3
7.2 Length of hoses and hose assemblies and tolerances .3
7.3 Concentricity .3
8 Physical properties of compounds . 3
9 Physical properties of finished hoses and hose assemblies . 4
10 Resistance to steam . 5
10.1 Principle .5
10.2 Short-term exposure .5
10.3 Long term test .5
10.4 Observations .5
10.5 Additional tests .5
11 Electrical resistance . 5
12 Type testing . 6
13 Marking . . 6
13.1 Hoses .6
13.2 Hose couplings .7
13.3 Identification of hose assemblies .7
14 Frequency of testing . . 7
15 Storage and admissible storage time . 8
Annex A (informative) Test frequency for hose assemblies in use . 9
Annex B (normative) Type and routine test . 10
Bibliography .11
iii
ISO 6134:2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee
SC 1, Rubber and plastics hoses and hose assemblies, in collaboration with the European Committee for
Standardization (CEN) Technical Committee CEN/TC 218, Rubber and plastics hoses and hose assemblies,
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.