EN 4631:2013
(Main)Aerospace series - Steel X4CrNiMo16-5-1 (1.4418) - Air melted - Hardened and tempered - Bar - De ≤ 200 mm - 900 MPa ≤ Rm ≤ 1 050 MPa
Aerospace series - Steel X4CrNiMo16-5-1 (1.4418) - Air melted - Hardened and tempered - Bar - De ≤ 200 mm - 900 MPa ≤ Rm ≤ 1 050 MPa
This standard specifies the requirements relating to:
Steel X4CrNiMo16-5-1 (1.4418)
Air melted
Hardened and tempered
Bar
De ≤ 200 mm
900 MPa ≤ Rm ≤ 1 050 MPa
for aerospace applications.
NOTE Other designation: Z 8 CND 17-04. Only the chemical composition of this standard must be considered.
Luft- und Raumfahrt - Stahl X4CrNiMo16-5-1 (1.4418) - Lufterschmolzen - Gehärtet- und angelassen - Stangen - De ≤ 200 mm - 900 MPa ≤ Rm ≤ 1 050 MPa
Diese Norm legt die Anforderungen an
Stahl X4CrNiMo16-5-1 (1.4418)
lufterschmolzen
gehärtet und angelassen
Stangen
De 200 mm
900 MPa Rm 1 050 MPa
zur Verwendung in der Luft- und Raumfahrt fest.
ANMERKUNG Andere Bezeichnung: Z 8 CND 17-04.
Nur die chemische Zusammensetzung dieser Norm ist zu berücksichtigen.
Série aérospatiale - Acier X4CrNiMo16-5-1 (1.4418) - Élaboré à l'air - Trempé et revenu - Barres - De ≤ 200 mm - 900 MPa ≤ Rm ≤ 1 050 MPa
Aeronavtika - Jeklo X4CrNiMo16-5-1 (1.4418) - Taljeno - Utrjeno in mehko žarjeno - Palica - De =< 200 mm - 900 MPa =< Rm =< 1050 MPa
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aeronavtika - Jeklo X4CrNiMo16-5-1 (1.4418) - Taljeno - Utrjeno in mehko žarjeno - Palica - De =< 200 mm - 900 MPa =< Rm =< 1050 MPa49.025.10JeklaSteelsICS:Ta slovenski standard je istoveten z:EN 4631:2013SIST EN 4631:2014en,fr,de01-februar-2014SIST EN 4631:2014SLOVENSKI
STANDARDSIST EN 4631:20081DGRPHãþD
SIST EN 4631:2014
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 4631
February 2013 ICS 49.025.10 Supersedes EN 4631:2007English Version
Aerospace series - Steel X4CrNiMo16-5-1 (1.4418) - Air melted - Hardened and tempered - Bar - De ≤ 200 mm - 900 MPa ≤ Rm ≤ 1 050 MPa
Série aérospatiale - Acier X4CrNiMo16-5-1 (1.4418) - Élaboré à l'air - Trempé et revenu - Barres - De ≤ 200 mm -900 MPa ≤ Rm ≤ 1 050 MPa
Luft- und Raumfahrt - Stahl X4CrNiMo16-5-1 (1.4418) - Lufterschmolzen - Gehärtet- und angelassen - Stangen - De ≤ 200 mm - 900 MPa ≤ Rm ≤ 1 050 MPa This European Standard was approved by CEN on 24 August 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 4631:2013: ESIST EN 4631:2014
EN 4631:2013 (E) 2 Contents Page Foreword . 3 Introduction . 4 1 Scope . 5 2 Normative references . 5
SIST EN 4631:2014
EN 4631:2013 (E) 3 Foreword This document (EN 4631:2013) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2013, and conflicting national standards shall be withdrawn at the latest by August 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 4631:2007. According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 4631:2014
EN 4631:2013 (E) 4 Introduction This standard is part of the series of EN metallic material standards for aerospace applications. The general organization of this series is described in EN 4258. This standard has been prepared in accordance with EN 4500-005. SIST EN 4631:2014
EN 4631:2013 (E) 5 1 Scope This European Standard specifies the requirements relating to: Steel X4CrNiMo16-5-1 (1.4418) Air melted Hardened and tempered Bar De ≤ 200
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.