EN ISO 148-1:2010

Metallic materials - Charpy pendulum impact test - Part 1: Test method (ISO 148-1:2009)

ISO 148-1:2009 specifies the Charpy pendulum impact (V‑notch and U‑notch) test method for determining the energy absorbed in an impact test of metallic materials.
ISO 148-1:2009 does not apply to instrumented impact testing, which is specified in ISO 14556.

Metallische Werkstoffe - Kerbschlagbiegeversuch nach Charpy -Teil 1: Prüfverfahren (ISO 148-1:2009)

Dieser Teil von ISO 148 gilt für Kerbschlagbiegeversuche nach Charpy (U- und V-Kerb) für metallische Werkstoffe
zur Bestimmung der verbrauchten Schlagenergie.
Dieser Teil von ISO 148 gilt nicht für den instrumentierten Kerbschlagbiegeversuch, der in ISO 14556 festgelegt
ist.

Matériaux métalliques - Essai de flexion par choc sur éprouvette Charpy - Partie 1: Méthode d'essai (ISO 148-1:2009)

L'ISO 148-1:2009 spécifie la méthode d'essai de flexion par choc sur éprouvette Charpy (avec entaille en V et avec entaille en U) pour déterminer l'énergie absorbée lors d'un essai de flexion par choc des matériaux métalliques.
Elle ne couvre pas l'essai de flexion par choc instrumenté, qui est spécifié dans l'ISO 14556.

Kovinski materiali - Udarni preskus žilavosti po Charpyju - 1. del: Preskusna metoda (ISO 148-1:2009)

Ta del ISO 148 določa udarno preskusno metodo žilavosti (V-zareza in U-zareza) po Charpyju za ugotavljanje absorbirane energije pri preskusu žilavosti kovinskih materialov. Ta del ISO 148 ne velja za udarni preskus z merilnimi napravami, ki je določen v ISO 14556.

General Information

• Status: Withdrawn
• Publication Date: 26-Oct-2010
• Withdrawal Date: 22-Nov-2016
• ICS: 77.040.10 - Mechanical testing of metals
• Technical Committee: ECISS/TC 101 - Test methods for steel (other than chemical analysis)
• Drafting Committee: ECISS/TC 101 - Test methods for steel (other than chemical analysis)
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 23-Nov-2016
• Ref Project: SIST EN ISO 148-1:2010 - Metallic materials - Charpy pendulum impact test - Part 1: Test method (ISO 148-1:2009)

Relations

• Replaces: EN 10045-1:1990 - Metallic materials - Charpy impact test - Part 1: Test method
• Effective Date: 11-Feb-2009
• Replaced By: EN ISO 148-1:2016 - Metallic materials - Charpy pendulum impact test - Part 1: Test method (ISO 148-1:2016)
• Effective Date: 28-Aug-2013

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 148-1:2010
01-december-2010
1DGRPHãþD
SIST EN 10045-1:1996
Kovinski materiali - Udarni preskus žilavosti po Charpyju - 1. del: Preskusna
metoda (ISO 148-1:2009)
Metallic materials - Charpy pendulum impact test - Part 1: Test method (ISO 148-1:2009)
Metallische Werkstoffe - Kerbschlagbiegeversuch nach Charpy -Teil 1: Prüfverfahren
(ISO 148-1:2009)
Matériaux métalliques - Essai de flexion par choc sur éprouvette Charpy - Partie 1:
Méthode d'essai (ISO 148-1:2009)
Ta slovenski standard je istoveten z: EN ISO 148-1:2010
ICS:
77.040.10 Mehansko preskušanje kovin Mechanical testing of metals
SIST EN ISO 148-1:2010 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 148-1:2010

---------------------- Page: 2 ----------------------

SIST EN ISO 148-1:2010


EUROPEAN STANDARD
EN ISO 148-1

NORME EUROPÉENNE

EUROPÄISCHE NORM
October 2010
ICS 77.040.10 Supersedes EN 10045-1:1990
English Version
Metallic materials - Charpy pendulum impact test - Part 1: Test
method (ISO 148-1:2009)
Matériaux métalliques - Essai de flexion par choc sur Metallische Werkstoffe - Kerbschlagbiegeversuch nach
éprouvette Charpy - Partie 1: Méthode d'essai (ISO 148- Charpy -Teil 1: Prüfverfahren (ISO 148-1:2009)
1:2009)
This European Standard was approved by CEN on 2 October 2010.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 148-1:2010: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 148-1:2010
EN ISO 148-1:2010 (E)
Contents Page
Foreword .3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 148-1:2010
EN ISO 148-1:2010 (E)
Foreword
The text of ISO 148-1:2009 has been prepared by Technical Committee ISO/TC 164 “Mechanical testing of
metals” of the International Organization for Standardization (ISO) and has been taken over as EN ISO 148-
1:2010 by Technical Committee ECISS/TC “Test methods for steel (other than chemical analysis)” the
secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by April 2011, and conflicting national standards shall be withdrawn at the
latest by April 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 10045-1:1990.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 148-1:2009 has been approved by CEN as a EN ISO 148-1:2010 without any modification.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 148-1:2010

---------------------- Page: 6 ----------------------

SIST EN ISO 148-1:2010

INTERNATIONAL ISO
STANDARD 148-1
Second edition
2009-11-15


Metallic materials — Charpy pendulum
impact test —
Part 1:
Test method
Matériaux métalliques — E
...